§49.162. Air quality permit by rule for new or modified true minor source auto body repair and miscellaneous surface coating operations in Indian country. — Inbound Citations

(a) As set forth in this Federal Implementation Plan (FIP), the Federal minor NSR program in Indian country (or “program”) consists of §§ 49.151 through 49.165.

(A) Auto body repair and miscellaneous surface coating operations (§ 49.162).

(c) If you propose to establish a synthetic minor source or synthetic minor HAP source or to construct a minor modification at your major source, you will have to comply with the requirements of the Federal minor NSR program in Indian country at §§ 49.151 through 49.165 or other EPA-approved minor NSR program, as applicable.

(B) The monthly exhaust filter pressure gauge readings specified in § 49.162(d)(3)(iii);

(v) The permittee shall promptly report to the reviewing authority any deviations as defined at 40 CFR 71.6(a)(3)(iii)(C) from permit by rule requirements including deviations attributable to upset conditions. (For the purposes of this permit by rule, promptly shall be defined to mean: At the time the annual report in § 49.162(d)(5)(iv) is submitted.) Deviation reports shall include:

(A) The identity of the affected emissions unit(s) where the deviation occurred;

(B) The nature of the deviation;

(C) The length of time of the deviation;

(D) The probable cause of the deviation; and

(E) Any corrective actions or preventive measures taken as a result of the deviation to minimize emissions from the deviation and to prevent future deviations.

(xiii) If the reviewing authority intends to terminate a permitted source's coverage under this permit by rule for cause as provided in § 49.162(d)(6), then the permittee shall apply for and obtain a source-specific permit as required by the reviewing authority.

(13) In lieu of meeting the requirements of paragraphs (e)(1) through (12) of this section, the permittee may use an airless/air-tight batch cleaning system provided that all of the following applicable requirements are met:

(i) The equipment is operated in accordance with the manufacturer's specifications and operated with a door or other pressure sealing apparatus that is in place during all cleaning and drying cycles.

(iii) All associated pressure relief devices shall not allow liquid solvents to drain out.

(iv) Spills during solvent transfer shall be wiped up immediately, and the used wipe rags shall be stored in closed containers that are handled in accordance with paragraph (e)(3) of this section.

(13) In lieu of meeting the requirements of paragraphs (e)(1) through (12) of this section, the permittee may use an airless/air-tight batch cleaning system provided that all of the following applicable requirements are met:

(i) The equipment is operated in accordance with the manufacturer's specifications and operated with a door or other pressure sealing apparatus that is in place during all cleaning and drying cycles.

(iii) All associated pressure relief devices shall not allow liquid solvents to drain out.

(iv) Spills during solvent transfer shall be wiped up immediately, and the used wipe rags shall be stored in closed containers that are handled in accordance with paragraph (e)(3) of this section.

(13) In lieu of meeting the requirements of paragraphs (e)(1) through (12) of this section, the permittee may use an airless/air-tight batch cleaning system provided that all of the following applicable requirements are met:

(i) The equipment is operated in accordance with the manufacturer's specifications and operated with a door or other pressure sealing apparatus that is in place during all cleaning and drying cycles.

(iii) All associated pressure relief devices shall not allow liquid solvents to drain out.

(iv) Spills during solvent transfer shall be wiped up immediately, and the used wipe rags shall be stored in closed containers that are handled in accordance with paragraph (e)(3) of this section.

(13) In lieu of meeting the requirements of paragraphs (e)(1) through (12) of this section, the permittee may use an airless/air-tight batch cleaning system provided that all of the following applicable requirements are met:

(i) The equipment is operated in accordance with the manufacturer's specifications and operated with a door or other pressure sealing apparatus that is in place during all cleaning and drying cycles.

(iii) All associated pressure relief devices shall not allow liquid solvents to drain out.

(iv) Spills during solvent transfer shall be wiped up immediately, and the used wipe rags shall be stored in closed containers that are handled in accordance with paragraph (e)(3) of this section.

(13) In lieu of meeting the requirements of paragraphs (e)(1) through (12) of this section, the permittee may use an airless/air-tight batch cleaning system provided that all of the following applicable requirements are met:

(i) The equipment is operated in accordance with the manufacturer's specifications and operated with a door or other pressure sealing apparatus that is in place during all cleaning and drying cycles.

(iii) All associated pressure relief devices shall not allow liquid solvents to drain out.

(iv) Spills during solvent transfer shall be wiped up immediately, and the used wipe rags shall be stored in closed containers that are handled in accordance with paragraph (e)(3) of this section.

(13) In lieu of meeting the requirements of paragraphs (e)(1) through (12) of this section, the permittee may use an airless/air-tight batch cleaning system provided that all of the following applicable requirements are met:

(i) The equipment is operated in accordance with the manufacturer's specifications and operated with a door or other pressure sealing apparatus that is in place during all cleaning and drying cycles.

(iii) All associated pressure relief devices shall not allow liquid solvents to drain out.

(iv) Spills during solvent transfer shall be wiped up immediately, and the used wipe rags shall be stored in closed containers that are handled in accordance with paragraph (e)(3) of this section.

(13) In lieu of meeting the requirements of paragraphs (e)(1) through (12) of this section, the permittee may use an airless/air-tight batch cleaning system provided that all of the following applicable requirements are met:

(i) The equipment is operated in accordance with the manufacturer's specifications and operated with a door or other pressure sealing apparatus that is in place during all cleaning and drying cycles.

(iii) All associated pressure relief devices shall not allow liquid solvents to drain out.

(iv) Spills during solvent transfer shall be wiped up immediately, and the used wipe rags shall be stored in closed containers that are handled in accordance with paragraph (e)(3) of this section.

(13) In lieu of meeting the requirements of paragraphs (e)(1) through (12) of this section, the permittee may use an airless/air-tight batch cleaning system provided that all of the following applicable requirements are met:

(i) The equipment is operated in accordance with the manufacturer's specifications and operated with a door or other pressure sealing apparatus that is in place during all cleaning and drying cycles.

(iii) All associated pressure relief devices shall not allow liquid solvents to drain out.

(iv) Spills during solvent transfer shall be wiped up immediately, and the used wipe rags shall be stored in closed containers that are handled in accordance with paragraph (e)(3) of this section.

(13) In lieu of meeting the requirements of paragraphs (e)(1) through (12) of this section, the permittee may use an airless/air-tight batch cleaning system provided that all of the following applicable requirements are met:

(i) The equipment is operated in accordance with the manufacturer's specifications and operated with a door or other pressure sealing apparatus that is in place during all cleaning and drying cycles.

(iii) All associated pressure relief devices shall not allow liquid solvents to drain out.

(iv) Spills during solvent transfer shall be wiped up immediately, and the used wipe rags shall be stored in closed containers that are handled in accordance with paragraph (e)(3) of this section.

(13) In lieu of meeting the requirements of paragraphs (e)(1) through (12) of this section, the permittee may use an airless/air-tight batch cleaning system provided that all of the following applicable requirements are met:

(i) The equipment is operated in accordance with the manufacturer's specifications and operated with a door or other pressure sealing apparatus that is in place during all cleaning and drying cycles.

(iii) All associated pressure relief devices shall not allow liquid solvents to drain out.

(iv) Spills during solvent transfer shall be wiped up immediately, and the used wipe rags shall be stored in closed containers that are handled in accordance with paragraph (e)(3) of this section.

(13) In lieu of meeting the requirements of paragraphs (e)(1) through (12) of this section, the permittee may use an airless/air-tight batch cleaning system provided that all of the following applicable requirements are met:

(i) The equipment is operated in accordance with the manufacturer's specifications and operated with a door or other pressure sealing apparatus that is in place during all cleaning and drying cycles.

(iii) All associated pressure relief devices shall not allow liquid solvents to drain out.

(iv) Spills during solvent transfer shall be wiped up immediately, and the used wipe rags shall be stored in closed containers that are handled in accordance with paragraph (e)(3) of this section.

(13) In lieu of meeting the requirements of paragraphs (e)(1) through (12) of this section, the permittee may use an airless/air-tight batch cleaning system provided that all of the following applicable requirements are met:

(i) The equipment is operated in accordance with the manufacturer's specifications and operated with a door or other pressure sealing apparatus that is in place during all cleaning and drying cycles.

(iii) All associated pressure relief devices shall not allow liquid solvents to drain out.

(iv) Spills during solvent transfer shall be wiped up immediately, and the used wipe rags shall be stored in closed containers that are handled in accordance with paragraph (e)(3) of this section.

(5) Training and certification will be valid for a period not to exceed 5 years after the date the training is completed, and all personnel must receive refresher training that meets the requirements of this § 49.162(f) and be re-certified every 5 years.