§98.232. GHGs to report. — Inbound Citations

(iv) An indication of whether the emissions identified via the notification are included in annual emissions reported under this subpart and, if so, the source type under which the emissions identified via the notification are reported (from the list of source types required to be reported as specified in § 98.232 for the facility's applicable industry segment). If the emissions were reported following the requirements of § 98.233(y) as an other large release event, report the unique release event identification number assigned to the other large release event as reported in paragraph (y)(2) of this section. If the emissions identified via the notification are not included in the annual emissions reported under this subpart, you must provide certification that the facility does not own or operate the equipment at the location identified in the notification as specified in § 98.233(y)(6)(i) or provide certification that the facility conducted a complete investigation of the site as specified in § 98.233(y)(6)(ii) and does not own or operate the emitting equipment at the location identified in the notification.

(a) You must report CO2, CH4, and N2O emissions from each industry segment specified in paragraphs (b) through (j) and (m) of this section, CO2, CH4, and N2O emissions from each flare as specified in paragraphs (b) through (j) of this section, and stationary and portable combustion emissions as applicable as specified in paragraph (k) of this section. You must also report the information specified in paragraph (l) of this section, as applicable.

(1) Facilities must report emissions from the onshore petroleum and natural gas production industry segment only if emission sources specified in § 98.232(c) emit 25,000 metric tons of CO2 equivalent or more per year.

(a) You must report CO2, CH4, and N2O emissions from each industry segment specified in paragraphs (b) through (j) and (m) of this section, CO2, CH4, and N2O emissions from each flare as specified in paragraphs (b) through (j) of this section, and stationary and portable combustion emissions as applicable as specified in paragraph (k) of this section. You must also report the information specified in paragraph (l) of this section, as applicable.

(1) If the entire facility is acquired by an owner or operator that does not already have a reporting facility in the same industry segment and basin (for onshore petroleum and natural gas production or onshore petroleum and natural gas gathering and boosting) or state (for natural gas distribution), then within 90 days after the change in the owner or operator, the designated representative or any alternate designated representative shall submit a certificate of representation that is complete under this section. If the new owner or operator already had emission sources specified in § 98.232(c), (i), (j), or (m), as applicable, prior to the acquisition in the same basin (for onshore petroleum and natural gas production or onshore petroleum and natural gas gathering and boosting) or state (for natural gas distribution) as the acquired facility but had not previously met the applicability requirements in §§ 98.2(a) and 98.231, then per the applicable definition of facility in § 98.238, the previously owned applicable emission sources must be included in the acquired facility. The new owner or operator and the new designated representative shall be responsible for submitting the annual report for the facility for the entire reporting year beginning with the reporting year in which the acquisition occurred.

(p) If you are required to report emissions from reciprocating compressor venting as specified in § 98.232(d)(1), (e)(1), (f)(1), (g)(1), and (h)(1), you must conduct volumetric emission measurements specified in paragraph (p)(1) of this section using methods specified in paragraphs (p)(2) through (5) of this section; perform calculations specified in paragraphs (p)(6) through (9) of this section; and calculate CH4 and CO2 mass emissions as specified in paragraph (p)(11) of this section. If you are required to report emissions from reciprocating compressor venting at an onshore petroleum and natural gas production facility as specified in § 98.232(c)(11) or an onshore petroleum and natural gas gathering and boosting facility as specified in § 98.232(j)(9), you must calculate volumetric emissions as specified in paragraph (p)(10) of this section and calculate CH4 and CO2 mass emissions as specified in paragraph (p)(11) of this section. If emissions from a compressor source are routed to a flare, paragraphs (p)(1) through (11) of this section do not apply and instead you must calculate CH4, CO2, and N2O emissions as specified in paragraph (n) of this section and report emissions from the flare as specified in § 98.236(n). If emissions from a compressor source are routed to combustion, paragraphs (p)(1) through (11) of this section do not apply and instead you must calculate and report emissions as specified in subpart C of this part or paragraph (z) of this section, as applicable. If emissions from a compressor source are routed to a vapor recovery system, paragraphs (p)(1) through (11) of this section do not apply.

(1) You must conduct volumetric emission measurements on each reciprocating compressor as specified in this paragraph. Compressor sources (as defined in § 98.238) without manifolded vents must use a measurement method specified in paragraph (p)(1)(i) or (ii) of this section. Manifolded compressor sources (as defined in § 98.238) must use a measurement method specified in paragraph (p)(1)(i), (ii), (iii), or (iv) of this section.

(i) Measure venting from each compressor according to either paragraph (p)(1)(i)(A), (B), or (C) of this section at least once annually, based on the compressor mode (as defined in § 98.238) in which the compressor was found at the time of measurement, except as specified in paragraph (p)(1)(i)(D) of this section. If additional measurements beyond the required annual testing are performed (including duplicate measurements or measurement of additional operating modes), then all measurements satisfying the applicable monitoring and QA/QC that is required by this paragraph (p) must be used in the calculations specified in this section.

(A) For a compressor measured in operating-mode, you must measure volumetric emissions from blowdown valve leakage through the blowdown vent as specified in paragraph (p)(2)(i) of this section, and measure volumetric emissions from reciprocating rod packing as specified in paragraph (p)(2)(ii) or (iii) of this section, as applicable.

(B) For a compressor measured in not-operating-depressurized-mode, you must measure volumetric emissions from isolation valve leakage as specified in paragraph (p)(2)(i) of this section. If a compressor is not operated and has blind flanges in place throughout the reporting period, measurement is not required in this compressor mode.

(C) For a compressor measured in standby-pressurized-mode, you must measure volumetric emissions from blowdown valve leakage through the blowdown vent as specified in paragraph (p)(2)(i) of this section and measure volumetric emissions from reciprocating rod packing as specified in paragraph (p)(2)(ii) or (iii) of this section, as applicable.

(D) An annual as found measurement is not required in the first year of operation for any new compressor that begins operation after as found measurements have been conducted for all existing compressors. For only the first year of operation of new compressors, calculate emissions according to paragraph (p)(6)(ii) of this section.

(ii) Instead of measuring the compressor source according to paragraph (p)(1)(i) of this section for a given compressor, you may elect to continuously measure volumetric emissions from a compressor source as specified in paragraph (p)(3) of this section.

(iii) For a compressor source that is part of a manifolded group of compressor sources (as defined in § 98.238), instead of measuring the compressor source according to paragraph (p)(1)(i), (ii), or (iv) of this section, you may elect to measure combined volumetric emissions from the manifolded group of compressor sources by conducting measurements at the common vent stack as specified in paragraph (p)(4) of this section. The measurements must be conducted at the frequency specified in paragraphs (p)(1)(iii)(A) and (B) of this section.

(A) A minimum of one measurement must be taken for each manifolded group of compressor sources in a calendar year.

(B) The measurement may be performed while the compressors are in any compressor mode.

(iv) For a compressor source that is part of a manifolded group of compressor sources, instead of measuring the compressor source according to paragraph (p)(1)(i), (ii), or (iii) of this section, you may elect to continuously measure combined volumetric emissions from the manifolded group of compressors sources as specified in paragraph (p)(5) of this section.

(2) . If conducting measurements for each compressor source, you must determine the volumetric emissions from blowdown valves and isolation valves as specified in paragraph (p)(2)(i) of this section. You must determine the volumetric emissions from reciprocating rod packing as specified in paragraph (p)(2)(ii) or (iii) of this section, as applicable.

(i) and for isolation valves on compressors in not-operating-depressurized-mode, determine the volumetric emissions using one of the methods specified in paragraphs (p)(2)(i)(A) through (D) of this section.

(A) Determine the volumetric flow at standard conditions from the blowdown vent using calibrated bagging or high volume sampler according to methods set forth in § 98.234(c) and (d), respectively.

(B) Determine the volumetric flow at standard conditions from the blowdown vent using a temporary meter such as a vane anemometer, according to methods set forth in § 98.234(b).

(C) Use an acoustic leak detection device according to methods set forth in § 98.234(a)(5).

(D) You may choose to use any of the methods set forth in § 98.234(a) to screen for emissions. If emissions are detected using the methods set forth in § 98.234(a), then you must use one of the methods specified in paragraphs (p)(2)(i)(A) through (C) of this section. If emissions are not detected using the methods in § 98.234(a), then you may assume that the volumetric emissions are zero. For the purposes of this paragraph, when using any of the methods in § 98.234(a), emissions are detected whenever a leak is detected according to the method.

(ii) For reciprocating rod packing equipped with an open-ended vent line on compressors in operating-mode or standby-pressurized-mode, determine the volumetric emissions using one of the methods specified in paragraphs (p)(2)(ii)(A) through (C) of this section.

(A) Determine the volumetric flow at standard conditions from the open-ended vent line using calibrated bagging or high volume sampler according to methods set forth in § 98.234(c) and (d), respectively.

(B) Determine the volumetric flow at standard conditions from the open-ended vent line using a temporary meter such as a vane anemometer, according to methods set forth in § 98.234(b).

(C) You may choose to use any of the methods set forth in § 98.234(a)(1) through (3) to screen for emissions. If emissions are detected using one of these specified methods, then you must use one of the methods specified in paragraphs (p)(2)(ii)(A) and (B) of this section. If emissions are not detected using the methods in § 98.234(a)(1) through (3), then you may assume that the volumetric emissions are zero. For the purposes of this paragraph (p)(2)(ii)(C), when using any of the methods in § 98.234(a), emissions are detected whenever a leak is detected according to the method. Acoustic leak detection is only applicable for through-valve leakage and is not applicable for screening or measuring rod packing emissions.

(iii) For reciprocating rod packing not equipped with an open-ended vent line on compressors in operating-mode, you must determine the volumetric emissions using the method specified in paragraphs (p)(2)(iii)(A) and (B) of this section.

(A) You must use the methods described in § 98.234(a)(1) through (3) to conduct annual leak detection of equipment leaks from the packing case into an open distance piece, or for compressors with a closed distance piece, conduct annual detection of gas emissions from the rod packing vent, distance piece vent, compressor crank case breather cap, or other vent emitting gas from the rod packing. Acoustic leak detection is only applicable for through-valve leakage and is not applicable for screening rod packing emissions.

(B) You must measure emissions found in paragraph (p)(2)(iii)(A) of this section using an appropriate meter, calibrated bag, or high volume sampler according to methods set forth in § 98.234(b), (c), and (d), respectively.

(3) . If you elect to conduct continuous volumetric emission measurements for an individual compressor source as specified in paragraph (p)(1)(ii) of this section, you must measure volumetric emissions as specified in paragraphs (p)(3)(i) and (p)(3)(ii) of this section.

(i) Continuously measure the volumetric flow for the individual compressor sources at standard conditions using a permanent meter according to methods set forth in § 98.234(b).

(ii) If compressor blowdown emissions are included in the metered emissions specified in paragraph (p)(3)(i) of this section, the compressor blowdown emissions may be included with the reported emissions for the compressor source and do not need to be calculated separately using the method specified in paragraph (i) of this section for blowdown vent stacks.

(4) . If conducting measurements for a manifolded group of compressor sources, you must measure volumetric emissions as specified in paragraphs (p)(4)(i) and (ii) of this section.

(i) Measure at a single point in the manifold downstream of all compressor inputs and, if practical, prior to comingling with other non-compressor emission sources.

(ii) Determine the volumetric flow at standard conditions from the common stack using one of the methods specified in paragraphs (p)(4)(ii)(A) through (F) of this section.

(A) A temporary meter such as a vane anemometer according to methods set forth in § 98.234(b).

(B) Calibrated bagging according to methods set forth in § 98.234(c).

(C) A high volume sampler according to methods set forth in § 98.234(d).

(D) [Reserved]

(E) You may choose to use any of the methods set forth in § 98.234(a)(1) through (3) to screen for emissions. If emissions are detected using one of these specified methods, then you must use one of the methods specified in paragraphs (p)(4)(ii)(A) through (D) of this section. If emissions are not detected using the methods in § 98.234(a)(1) through (3), then you may assume that the volumetric emissions are zero. For the purposes of this paragraph, when using any of the methods in § 98.234(a), emissions are detected whenever a leak is detected according to the method. Acoustic leak detection is only applicable for through-valve leakage and is not applicable for screening a manifolded group of compressor sources.

(F) If one of the screening methods specified in § 98.234(a)(1) through (3) identifies a leak in a manifolded group of reciprocating compressor sources, you may use acoustic leak detection, according to § 98.234(a)(5), to identify the source of the leak. You must use one of the methods specified in paragraphs (p)(4)(ii)(A) through (D) of this section to quantify the emissions from the identified source.

(5) . If you elect to conduct continuous volumetric emission measurements for a manifolded group of compressor sources as specified in paragraph (p)(1)(iv) of this section, you must measure volumetric emissions as specified in paragraphs (p)(5)(i) through (iii) of this section.

(i) Measure at a single point in the manifold downstream of all compressor inputs and, if practical, prior to comingling with other non-compressor emission sources.

(ii) Continuously measure the volumetric flow for the manifolded group of compressor sources at standard conditions using a permanent meter according to methods set forth in § 98.234(b).

(iii) If compressor blowdown emissions are included in the metered emissions specified in paragraph (p)(5)(ii) of this section, the compressor blowdown emissions may be included with the reported emissions for the manifolded group of compressor sources and do not need to be calculated separately using the method specified in paragraph (i) of this section for blowdown vent stacks.

(6) . For compressor sources measured according to paragraph (p)(1)(i) of this section, you must calculate GHG emissions from the compressor sources as specified in paragraphs (p)(6)(i) through (iv) of this section.

(i) Using equation W-26 to this section, calculate the annual volumetric GHG emissions for each reciprocating compressor mode-source combination specified in paragraphs (p)(1)(i)(A) through (C) of this section that was measured during the reporting year.

(ii) Using equation W-27 to this section, calculate the annual volumetric GHG emissions from each reciprocating compressor mode-source combination specified in paragraphs (p)(1)(i)(A) through (C) of this section that was not measured during the reporting year.

(iii) Using equation W-28 to this section, develop an emission factor for each compressor mode-source combination specified in paragraphs (p)(1)(i)(A) through (C) of this section. These emission factors must be calculated annually and used in equation W-27 to this section to determine volumetric emissions from a reciprocating compressor in the mode-source combinations that were not measured in the reporting year.

(iv) The reporter emission factor in equation W-28 to this section may be calculated by using all measurements from a single owner or operator instead of only using measurements from a single facility. If you elect to use this option, the reporter emission factor must be applied to all reporting facilities for the owner or operator.

(7) . For compressor sources measured according to paragraph (p)(1)(ii) of this section, you must use the continuous volumetric emission measurements taken as specified in paragraph (p)(3) of this section and calculate annual volumetric GHG emissions associated with the compressor source using equation W-29A to this section.

(8) For manifolded groups of compressor sources measured according to paragraph (p)(1)(iii) of this section, you must calculate annual GHG emissions using equation W-29B to this section. If the reciprocating compressors included in the manifolded group of compressor sources share the manifold with centrifugal compressors, you must follow the procedures in either this paragraph (p)(8) or paragraph (o)(8) of this section to calculate emissions from the manifolded group of compressor sources.

(9) . For a manifolded group of compressor sources measured according to paragraph (p)(1)(iv) of this section, you must use the continuous volumetric emission measurements taken as specified in paragraph (p)(5) of this section and calculate annual volumetric GHG emissions associated with each manifolded group of compressor sources using equation W-29C to this section. If the reciprocating compressors included in the manifolded group of compressor sources share the manifold with centrifugal compressors, you must follow the procedures in either this paragraph (p)(9) or paragraph (o)(9) of this section to calculate emissions from the manifolded group of compressor sources.

(10) . You must calculate volumetric emissions from reciprocating compressors at an onshore petroleum and natural gas production facility or an onshore petroleum and natural gas gathering and boosting facility as specified in paragraphs (p)(10)(i) through (iv) of this section, as applicable.

(i) For all reciprocating compressors at an onshore petroleum and natural gas production facility or an onshore petroleum and natural gas gathering and boosting facility that are subject to the reciprocating compressor standards in § 60.5385b of this chapter or an applicable approved state plan or applicable Federal plan in part 62 of this chapter, you must conduct the volumetric emission measurements as required by § 60.5385b(b) and (c) of this chapter or an applicable approved state plan or applicable Federal plan in part 62 of this chapter, conduct any additional volumetric emission measurements specified in paragraph (p)(1) of this section using methods specified in paragraphs (p)(2) through (5) of this section (based on the compressor mode (as defined in § 98.238) in which the compressor was found at the time of measurement), and calculate emissions as specified in paragraphs (p)(6) through (9) of this section. Conduct all measurements required by this paragraph (p)(10)(i) at the frequency specified by § 60.5385b(a) of this chapter or an applicable approved state plan or applicable Federal plan in part 62 of this chapter. For any reporting year in which measuring at the frequency specified by § 60.5385b(a) of this chapter results in measurement not being required for a subject compressor, calculate emissions for all mode-source combinations as specified in paragraph (p)(6)(ii) of this section.

(ii) For all reciprocating compressors at an onshore petroleum and natural gas production facility or an onshore petroleum and natural gas gathering and boosting facility that are not subject to the reciprocating compressor standards in § 60.5385b of this chapter or an applicable approved state plan or applicable Federal plan in part 62 of this chapter, you may elect to conduct volumetric emission measurements specified in paragraph (p)(1) of this section using methods specified in paragraphs (p)(2) through (5) of this section (based on the compressor mode (as defined in § 98.238) in which the compressor was found at the time of measurement), and calculate emissions as specified in paragraphs (p)(6) through (9) of this section.

(iii) For all reciprocating compressors at an onshore petroleum and natural gas production facility or an onshore petroleum and natural gas gathering and boosting facility for which paragraph (p)(10)(i) of this section does not apply, and you do not elect to conduct volumetric emission measurements specified in paragraph (p)(1) of this section, you must calculate total atmospheric rod packing emissions from all reciprocating compressors at either an onshore petroleum and natural gas production facility or an onshore petroleum and natural gas gathering and boosting facility using equation W-29D to this section. Reciprocating compressor rod packing emissions that are routed to a flare, combustion, or vapor recovery system are not required to be determined under this paragraph (p).

(iv) For all reciprocating compressors at an onshore petroleum and natural gas production facility or an onshore petroleum and natural gas gathering and boosting facility for which paragraph (p)(10)(i) of this section does not apply, you must calculate rod packing vent emissions from each reciprocating compressor using equation W-29E to this section. Reciprocating compressor rod packing emissions that are routed to a flare, combustion, or vapor recovery system are not required to be determined under this paragraph (p).

(11) You must calculate both CH4 and CO2 mass emissions from volumetric emissions using calculations in paragraph (v) of this section.

(o) If you are required to report emissions from centrifugal compressor venting as specified in § 98.232(d)(2), (e)(2), (f)(2), (g)(2), and (h)(2), you must conduct volumetric emission measurements specified in paragraph (o)(1) of this section using methods specified in paragraphs (o)(2) through (5) of this section; perform calculations specified in paragraphs (o)(6) through (9) of this section; and calculate CH4 and CO2 mass emissions as specified in paragraph (o)(11) of this section. If you are required to report emissions from centrifugal compressor venting at an onshore petroleum and natural gas production facility as specified in § 98.232(c)(19) or an onshore petroleum and natural gas gathering and boosting facility as specified in § 98.232(j)(8), you must calculate volumetric emissions as specified in paragraph (o)(10) of this section and calculate CH4 and CO2 mass emissions as specified in paragraph (o)(11) of this section. If emissions from a compressor source are routed to a flare, paragraphs (o)(1) through (11) of this section do not apply and instead you must calculate CH4, CO2, and N2O emissions as specified in paragraph (n) of this section and report emissions from the flare as specified in § 98.236(n). If emissions from a compressor source are routed to combustion, paragraphs (o)(1) through (11) of this section do not apply and instead you must calculate and report emissions as specified in subpart C of this part or paragraph (z) of this section, as applicable. If emissions from a compressor source are routed to a vapor recovery system, paragraphs (o)(1) through (11) of this section do not apply.

(1) You must conduct volumetric emission measurements on each centrifugal compressor as specified in this paragraph. Compressor sources (as defined in § 98.238) without manifolded vents must use a measurement method specified in paragraph (o)(1)(i) or (ii) of this section. Manifolded compressor sources (as defined in § 98.238) must use a measurement method specified in paragraph (o)(1)(i), (ii), (iii), or (iv) of this section.

(i) Measure venting from each compressor according to either paragraph (o)(1)(i)(A), (B), or (C) of this section at least once annually, based on the compressor mode (as defined in § 98.238) in which the compressor was found at the time of measurement, except as specified in paragraph (o)(1)(i)(D) of this section. If additional measurements beyond the required annual testing are performed (including duplicate measurements or measurement of additional operating modes), then all measurements satisfying the applicable monitoring and QA/QC that is required by this paragraph (o) must be used in the calculations specified in this section.

(A) For a compressor measured in operating-mode, you must measure volumetric emissions from blowdown valve leakage through the blowdown vent as specified in paragraph (o)(2)(i) of this section, measure volumetric emissions from wet seal oil degassing vents as specified in paragraph (o)(2)(ii) of this section if the compressor has wet seal oil degassing vents, and measure volumetric emissions from dry seal vents as specified in paragraph (o)(2)(iii) of this section if the compressor has dry seals.

(B) For a compressor measured in not-operating-depressurized-mode, you must measure volumetric emissions from isolation valve leakage as specified in paragraph (o)(2)(i) of this section. If a compressor is not operated and has blind flanges in place throughout the reporting period, measurement is not required in this compressor mode.

(C) For a compressor measured in standby-pressurized-mode, you must measure volumetric emissions from blowdown valve leakage through the blowdown vent as specified in paragraph (o)(2)(i) of this section, measure volumetric emissions from wet seal oil degassing vents as specified in paragraph (o)(2)(ii) of this section if the compressor has wet seal oil degassing vents, and measure volumetric emissions from dry seal vents as specified in paragraph (o)(2)(iii) of this section if the compressor has dry seals.

(D) An annual as found measurement is not required in the first year of operation for any new compressor that begins operation after as found measurements have been conducted for all existing compressors. For only the first year of operation of new compressors, calculate emissions according to paragraph (o)(6)(ii) of this section.

(ii) Instead of measuring the compressor source according to paragraph (o)(1)(i) of this section for a given compressor, you may elect to continuously measure volumetric emissions from a compressor source as specified in paragraph (o)(3) of this section.

(iii) For a compressor source that is part of a manifolded group of compressor sources (as defined in § 98.238), instead of measuring the compressor source according to paragraph (o)(1)(i), (ii), or (iv) of this section, you may elect to measure combined volumetric emissions from the manifolded group of compressor sources by conducting measurements at the common vent stack as specified in paragraph (o)(4) of this section. The measurements must be conducted at the frequency specified in paragraphs (o)(1)(iii)(A) and (B) of this section.

(A) A minimum of one measurement must be taken for each manifolded group of compressor sources in a calendar year.

(B) The measurement may be performed while the compressors are in any compressor mode.

(iv) For a compressor source that is part of a manifolded group of compressor sources, instead of measuring the compressor source according to paragraph (o)(1)(i), (ii), or (iii) of this section, you may elect to continuously measure combined volumetric emissions from the manifolded group of compressor sources as specified in paragraph (o)(5) of this section.

(2) . If conducting measurements for each compressor source, you must determine the volumetric emissions from blowdown valves and isolation valves as specified in paragraph (o)(2)(i) of this section, the volumetric emissions from wet seal oil degassing vents as specified in paragraph (o)(2)(ii) of this section, and the volumetric emissions from dry seal vents as specified in paragraph (o)(2)(iii) of this section.

(i) For blowdown valves on compressors in operating-mode or in standby-pressurized-mode and for isolation valves on compressors in not-operating-depressurized-mode, determine the volumetric emissions using one of the methods specified in paragraphs (o)(2)(i)(A) through (D) of this section.

(A) Determine the volumetric flow at standard conditions from the blowdown vent using calibrated bagging or high volume sampler according to methods set forth in § 98.234(c) and § 98.234(d), respectively.

(B) Determine the volumetric flow at standard conditions from the blowdown vent using a temporary meter such as a vane anemometer according to methods set forth in § 98.234(b).

(C) Use an acoustic leak detection device according to methods set forth in § 98.234(a)(5).

(D) You may choose to use any of the methods set forth in § 98.234(a) to screen for emissions. If emissions are detected using the methods set forth in § 98.234(a), then you must use one of the methods specified in paragraph (o)(2)(i)(A) through (C) of this section. If emissions are not detected using the methods in § 98.234(a), then you may assume that the volumetric emissions are zero. For the purposes of this paragraph, when using any of the methods in § 98.234(a), emissions are detected whenever a leak is detected according to the methods.

(ii) For wet seal oil degassing vents in operating-mode or in standby-pressurized-mode, determine volumetric flow at standard conditions, using one of the methods specified in paragraphs (o)(2)(ii)(A) through (C) of this section. You must quantitatively measure the volumetric flow for wet seal oil degassing vent; you may not use screening methods set forth in § 98.234(a) to screen for emissions for the wet seal oil degassing vent.

(A) Use a temporary meter such as a vane anemometer or permanent flow meter according to methods set forth in § 98.234(b).

(B) Use calibrated bags according to methods set forth in § 98.234(c).

(C) Use a high volume sampler according to methods set forth in § 98.234(d).

(iii) For dry seal vents in operating-mode or in standby-pressurized-mode, determine volumetric flow at standard conditions from each dry seal vent using one of the methods specified in paragraphs (o)(2)(iii)(A) through (D) of this section. The measurement should be conducted on the compressor side dry seal. If a compressor has more than one dry seal vent, determine the aggregate dry seal vent volumetric flow for the compressor as the sum of the volumetric flows determined for each dry seal vent on the compressor.

(A) Use a temporary meter such as a vane anemometer or permanent flow meter according to methods set forth in § 98.234(b).

(B) Use calibrated bags according to methods set forth in § 98.234(c).

(C) Use a high volume sampler according to methods set forth in § 98.234(d).

(D) You may choose to use any of the methods set forth in § 98.234(a)(1) through (3) to screen for emissions. If emissions are detected using one of these specified methods, then you must use one of the methods specified in paragraph (o)(2)(iii)(A) through (C) of this section. If emissions are not detected using the methods in § 98.234(a)(1) through (3), then you may assume that the volumetric emissions are zero. For the purposes of this paragraph, when using any of the methods in § 98.234(a), emissions are detected whenever a leak is detected according to the methods. Acoustic leak detection is only applicable for through-valve leakage and is not applicable for screening dry seal vents.

(3) If you elect to conduct continuous volumetric emission measurements for an individual compressor source as specified in paragraph (o)(1)(ii) of this section, you must measure volumetric emissions as specified in paragraphs (o)(3)(i) and (ii) of this section.

(i) Continuously measure the volumetric flow for the individual compressor source at standard conditions using a permanent meter according to methods set forth in § 98.234(b).

(ii) If compressor blowdown emissions are included in the metered emissions specified in paragraph (o)(3)(i) of this section, the compressor blowdown emissions may be included with the reported emissions for the compressor source and do not need to be calculated separately using the method specified in paragraph (i) of this section for blowdown vent stacks.

(4) If conducting measurements for a manifolded group of compressor sources, you must measure volumetric emissions as specified in paragraphs (o)(4)(i) and (ii) of this section.

(i) Measure at a single point in the manifold downstream of all compressor inputs and, if practical, prior to comingling with other non-compressor emission sources.

(ii) Determine the volumetric flow at standard conditions from the common stack using one of the methods specified in paragraphs (o)(4)(ii)(A) through (F) of this section.

(A) A temporary meter such as a vane anemometer according the methods set forth in § 98.234(b).

(B) Calibrated bagging according to methods set forth in § 98.234(c).

(C) A high volume sampler according to methods set forth § 98.234(d).

(D) [Reserved]

(E) You may choose to use any of the methods set forth in § 98.234(a)(1) through (3) to screen for emissions. If emissions are detected using one of these methods, then you must use one of the methods specified in paragraph (o)(4)(ii)(A) through (D) of this section. If emissions are not detected using the methods in § 98.234(a)(1) through (3), then you may assume that the volumetric emissions are zero. For the purposes of this paragraph, when using any of the methods in § 98.234(a), emissions are detected whenever a leak is detected according to the method. Acoustic leak detection is only applicable for through-valve leakage and is not applicable for screening a manifolded group of compressor sources.

(F) If one of the screening methods specified in § 98.234(a)(1) through (3) identifies a leak in a manifolded group of centrifugal compressor sources, you may use acoustic leak detection, according to § 98.234(a)(5), to identify the source of the leak. You must use one of the methods specified in paragraphs (o)(4)(ii)(A) through (D) of this section to quantify emissions from the identified source.

(5) If you elect to conduct continuous volumetric emission measurements for a manifolded group of compressor sources as specified in paragraph (o)(1)(iv) of this section, you must measure volumetric emissions as specified in paragraphs (o)(5)(i) through (iii) of this section.

(i) Measure at a single point in the manifold downstream of all compressor inputs and, if practical, prior to comingling with other non-compressor emission sources.

(ii) Continuously measure the volumetric flow for the manifolded group of compressor sources at standard conditions using a permanent meter according to methods set forth in § 98.234(b).

(iii) If compressor blowdown emissions are included in the metered emissions specified in paragraph (o)(5)(ii) of this section, the compressor blowdown emissions may be included with the reported emissions for the manifolded group of compressor sources and do not need to be calculated separately using the method specified in paragraph (i) of this section for blowdown vent stacks.

(6) . For compressor sources measured according to paragraph (o)(1)(i) of this section, you must calculate annual GHG emissions from the compressor sources as specified in paragraphs (o)(6)(i) through (iv) of this section.

(i) Using equation W-21 to this section, calculate the annual volumetric GHG emissions for each centrifugal compressor mode-source combination specified in paragraphs (o)(1)(i)(A) through (C) of this section that was measured during the reporting year.

(ii) Using equation W-22 to this section, calculate the annual volumetric GHG emissions from each centrifugal compressor mode-source combination specified in paragraphs (o)(1)(i)(A) through (C) of this section that was not measured during the reporting year.

(iii) Using equation W-23 to this section, develop an emission factor for each compressor mode-source combination specified in paragraphs (o)(1)(i)(A) through (C) of this section. These emission factors must be calculated annually and used in equation W-22 to this section to determine volumetric emissions from a centrifugal compressor in the mode- source combinations that were not measured in the reporting year.

(iv) The reporter emission factor in equation W-23 to this section may be calculated by using all measurements from a single owner or operator instead of only using measurements from a single facility. If you elect to use this option, the reporter emission factor must be applied to all reporting facilities for the owner or operator.

(7) . For compressor sources measured according to paragraph (o)(1)(ii) of this section, you must use the continuous volumetric emission measurements taken as specified in paragraph (o)(3) of this section and calculate annual volumetric GHG emissions associated with the compressor source using equation W-24A to this section.

(8) . For manifolded groups of compressor sources measured according to paragraph (o)(1)(iii) of this section, you must calculate annual volumetric GHG emissions using equation W-24B to this section. If the centrifugal compressors included in the manifolded group of compressor sources share the manifold with reciprocating compressors, you must follow the procedures in either this paragraph (o)(8) or paragraph (p)(8) of this section to calculate emissions from the manifolded group of compressor sources.

(9) For a manifolded group of compressor sources measured according to paragraph (o)(1)(iv) of this section, you must use the continuous volumetric emission measurements taken as specified in paragraph (o)(5) of this section and calculate annual volumetric GHG emissions associated with each manifolded group of compressor sources using equation W-24C to this section. If the centrifugal compressors included in the manifolded group of compressor sources share the manifold with reciprocating compressors, you must follow the procedures in either this paragraph (o)(9) or paragraph (p)(9) of this section to calculate emissions from the manifolded group of compressor sources.

(10) You must calculate volumetric emissions from centrifugal compressors at an onshore petroleum and natural gas production facility or an onshore petroleum and natural gas gathering and boosting facility as specified in paragraphs (o)(10)(i) through (iv), as applicable.

(i) For all centrifugal compressors at an onshore petroleum and natural gas production facility or an onshore petroleum and natural gas gathering and boosting facility that are subject to the centrifugal compressor standards in § 60.5380b of this chapter or an applicable approved state plan or applicable Federal plan in part 62 of this chapter for dry seals and self-contained wet seals, you must conduct the volumetric emission measurements as required by § 60.5380b(a)(5) of this chapter or an applicable approved state plan or applicable Federal plan in part 62 of this chapter, conduct all additional volumetric emission measurements specified in paragraph (o)(1) of this section using methods specified in paragraphs (o)(2) through (5) of this section (based on the compressor mode (as defined in § 98.238) in which the compressor was found at the time of measurement), and calculate emissions as specified in paragraphs (o)(6) through (9) of this section. Conduct all measurements required by this paragraph (o)(10)(i) at the frequency specified by § 60.5380b(a)(4) of this chapter or an applicable approved state plan or applicable Federal plan in part 62 of this chapter. For any reporting year in which measuring at the frequency specified by § 60.5380b(a)(4) of this chapter results in measurement not being required for a subject compressor, calculate emissions for all mode-source combinations as specified in paragraph (o)(6)(ii) of this section.

(ii) For all centrifugal compressors at an onshore petroleum and natural gas production facility or an onshore petroleum and natural gas gathering and boosting facility that are not subject to the centrifugal compressor standards in § 60.5380b of this chapter or an applicable approved state plan or applicable Federal plan in part 62 of this chapter for dry seals and self-contained wet seals, you may elect to conduct the volumetric emission measurements specified in paragraph (o)(1) of this section using methods specified in paragraphs (o)(2) through (5) of this section (based on the compressor mode (as defined in § 98.238) in which the compressor was found at the time of measurement), and calculate emissions as specified in paragraphs (o)(6) through (9) of this section.

(iii) For all centrifugal compressors at an onshore petroleum and natural gas production facility or an onshore petroleum and natural gas gathering and boosting facility for which paragraph (o)(10)(i) of this section does not apply and you do not elect to conduct the volumetric measurements specified in paragraph (o)(1) of this section, you must calculate total atmospheric wet seal oil degassing vent emissions from all centrifugal compressors at either an onshore petroleum and natural gas production facility or an onshore petroleum and natural gas gathering and boosting facility using equation W-25A to this section. Emissions from centrifugal compressor wet seal oil degassing vents that are routed to a flare, combustion, or vapor recovery system are not required to be determined under this paragraph (o).

(iv) For all centrifugal compressors at an onshore petroleum and natural gas production facility or an onshore petroleum and natural gas gathering and boosting facility for which paragraph (o)(10)(i) of this section does not apply, and you do not elect to conduct the volumetric measurements specified in paragraph (o)(1) of this section, you must calculate wet seal oil degassing vent emissions from each centrifugal compressor using equation W-25B to this section. Emissions from centrifugal compressor wet seal oil degassing vents that are routed to a flare, combustion, or vapor recovery system are not required to be determined under this paragraph (o).

(11) . You must calculate both CH4 and CO2 mass emissions from volumetric emissions using calculations in paragraph (v) of this section.

(2) You must indicate whether your facility contains any of the component types subject to or complying with § 98.233(q) that are listed in § 98.232(c)(21), (d)(7), (e)(7) or (8), (f)(5) through (8), (g)(4), (g)(6) or (7), (h)(5), (h)(7) or (8), (i)(1), (j)(10), (m)(3)(ii) or (m)(4)(ii) for your facility's industry segment. For each component type and leak detection method combination that is located at your well-pad site, gathering and boosting site, or facility, you must report the information specified in paragraphs (q)(2)(i) through (ix) of this section. If a component type is located at your well-pad site, gathering and boosting site, or facility and no leaks were identified from that component, then you must report the information in paragraphs (q)(2)(i) through (ix) of this section but report a zero (“0”) for the information required according to paragraphs (q)(2)(vi) through (ix) of this section. If you used Calculation Method 1 (leaker factor emission calculation methodology) for some complete leak surveys and used Calculation Method 2 (leaker measurement methodology) for some complete leak surveys, you must report the information specified in paragraphs (q)(2)(i) through (ix) of this section separately for component surveys using Calculation Method 1 and Calculation Method 2.

(i) Well-pad ID (for the onshore petroleum and natural gas production industry segment only) or gathering and boosting site ID (for the onshore petroleum and natural gas gathering and boosting industry segment only).

(iii) Leak detection method used for the screening survey (e.g., Method 21 as specified in § 98.234(a)(2)(i); Method 21 as specified in § 98.234(a)(2)(ii); and OGI and other leak detection methods as specified in § 98.234(a)(1), (3), or (5)).

(iv) Emission factor or measurement method used (e.g., default emission factor; facility-specific emission factor developed according to § 98.233(q)(4); or direct measurement according to § 98.233(q)(3)).

(vi) Total number of the surveyed component types by leak detection method that were identified as leaking in the calendar year (“xp” in equation W-30 to § 98.233 for the component type or the number of leaks measured for the specified component type according to the provisions in § 98.233(q)(3)).

(vii) Average time the surveyed components are assumed to be leaking and operational, in hours (average of “Tp,z” from equation W-30 to § 98.233 for the component type or average duration of leaks for the specified component type determined according to the provisions in § 98.233(q)(3)(ii)).

(viii) Annual CO2 emissions, in metric tons CO2, for the component type as calculated using equation W-30 to § 98.233 or § 98.233(q)(3)(vii) (for surveyed components only).

(ix) Annual CH4 emissions, in metric tons CH4, for the component type as calculated using equation W-30 to § 98.233 or § 98.233(q)(3)(vii) (for surveyed components only).

(iii) For the components listed in § 98.232(c)(21)(i), (e)(7) and (8), (f)(5) through (8), (g)(4), (g)(6) and (7), (h)(5), (h)(7) and (8), and (j)(10)(i) that are subject to the well site or compressor station fugitive emissions standards in § 60.5397a of this chapter, the fugitive emissions standards for well sites, centralized production facilities, and compressor stations in § 60.5397b or 60.5398b of this chapter, or an applicable approved state plan or applicable Federal plan in part 62 of this chapter, and are required to conduct surveys using any of the leak detection methods in § 98.234(a)(1)(ii) or (iii) or (a)(2)(ii), as applicable, you must use the results of those surveys to calculate equipment leak emissions using the procedures specified in either paragraph (q)(2) or (3) of this section.

(r) This paragraph (r) applies to emissions sources listed in § 98.232(c)(21)(ii), (f)(7), (g)(5), (h)(6), (j)(10)(ii), (m)(3)(i), and (m)(4)(i) if you are not required to comply with paragraph (q) of this section and if you do not elect to comply with paragraph (q) of this section for these components in lieu of this paragraph (r). This paragraph (r) also applies to emission sources listed in § 98.232(i)(2) through (6), (j)(11), and (m)(5). To be subject to the requirements of this paragraph (r), the listed emissions sources also must contact streams with gas content greater than 10 percent CH4 plus CO2 by weight. Emissions sources that contact streams with gas content less than or equal to 10 percent CH4 plus CO2 by weight are exempt from the requirements of this paragraph (r) and do not need to be reported. Tubing systems equal to or less than one half inch diameter are exempt from the requirements of this paragraph (r) and do not need to be reported. Equipment leak components in vacuum service are exempt from the survey and emission estimation requirements of this paragraph (r) and only the count of these equipment must be reported. You must calculate emissions from all emission sources listed in this paragraph (r) using equation W-32A to this section, except for natural gas distribution facility emission sources listed in § 98.232(i)(3). Natural gas distribution facility emission sources listed in § 98.232(i)(3) must calculate emissions using equation W-32B to this section and according to paragraph (r)(6)(ii) of this section.

(1) Calculate both CH4 and CO2 mass emissions from volumetric emissions using calculations in paragraph (v) of this section.

(2) Onshore petroleum and natural gas production facilities and onshore petroleum and natural gas gathering and boosting facilities must use the appropriate default whole gas population emission factors listed in table W-1 to this subpart. Major equipment associated with gas wells are considered gas service equipment in table W-1 to this subpart. Onshore petroleum and natural gas gathering and boosting facilities shall use the gas service equipment emission factors in table W-1 to this subpart. Major equipment associated with crude oil wells are considered crude service equipment in table W-1 to this subpart. Where facilities conduct EOR operations, the emission factor listed in table W-1 to this subpart shall be used to estimate all streams of gases, including recycle CO2 stream. For meters/piping, use one meters/piping per well-pad for onshore petroleum and natural gas production operations and the number of meters in the facility for onshore petroleum and natural gas gathering and boosting operations.

(3) Underground natural gas storage facilities must use the appropriate default total hydrocarbon population emission factors for storage wellheads in gas service listed in table W-3 to this subpart.

(4) LNG storage facilities must use the appropriate default methane population emission factors for LNG storage compressors in gas service listed in table W-5 to this subpart.

(5) LNG import and export facilities must use the appropriate default methane population emission factors for LNG terminal compressors in gas service listed in table W-5 to this subpart.

(6) Natural gas distribution facilities must use the appropriate methane emission factors as described in paragraphs (r)(6)(i) and (ii) of this section.

(i) Below grade transmission-distribution transfer stations, below grade metering-regulating stations, distribution mains, and distribution services must use the appropriate default methane population emission factors listed in table W-5 to this subpart to estimate emissions from components listed in § 98.232(i)(2), (4), (5), and (6), respectively.

(ii) Above grade metering-regulating stations that are not above grade transmission-distribution transfer stations must use the meter/regulator run population emission factor calculated in equation W-31 to this section in accordance with paragraph (q)(2)(x) or (q)(3)(viii)(A) of this section for the components listed in § 98.232(i)(3). Natural gas distribution facilities that do not have above grade transmission-distribution transfer stations are not required to calculate emissions for above grade metering-regulating stations and are not required to report GHG emissions in § 98.236(r)(2)(v).

(7) Onshore natural gas transmission pipeline facilities must use the appropriate default methane population emission factors listed in table W-5 to this subpart to estimate emissions from components listed in § 98.232(m)(3)(i), (4)(i) and (5).

(z) If your facility is required by § 98.232(c)(22), (i)(7), or (j)(12) to report emissions from combustion equipment, then you must indicate whether your facility has any combustion units subject to reporting according to paragraph (a)(1)(xx), (a)(8)(vi), or (a)(9)(xiii) of this section. If your facility contains any combustion units subject to reporting according to paragraph (a)(1)(xx), (a)(8)(vi), or (a)(9)(xiii) of this section, then you must report the information specified in paragraphs (z)(1) and (2) of this section, as applicable. You must report the information specified in paragraphs (z)(1) and (2) of this section, as applicable, for each well-pad site (for onshore petroleum and natural gas production), gathering and boosting site (for onshore petroleum and natural gas gathering and boosting), or facility (for all other applicable industry segments).

(1) External fuel combustion units with a rated heat capacity less than or equal to 5 million Btu per hour; or, internal fuel combustion units that are not compressor-drivers, with a rated heat capacity less than or equal to 1 mmBtu/hr (or the equivalent of 130 horsepower). If the facility contains external fuel combustion units with a rated heat capacity less than or equal to 5 million Btu per hour or internal fuel combustion units that are not compressor-drivers, with a rated heat capacity less than or equal to 1 million Btu per hour (or the equivalent of 130 horsepower), then you must report the information specified in paragraphs (z)(1)(i) through (iii) of this section for each unit type.

(i) Well-pad ID (for the onshore petroleum and natural gas production industry segment only) or gathering and boosting site ID (for the onshore petroleum and natural gas gathering and boosting industry segment only).

(2) External fuel combustion units with a rated heat capacity greater than 5 million Btu per hour; internal fuel combustion units that are not compressor-drivers, with a rated heat capacity greater than 1 million Btu per hour (or the equivalent of 130 horsepower); or, internal fuel combustion units of any heat capacity that are compressor-drivers. For each type of combustion unit at your facility, you must report the information specified in paragraphs (z)(2)(i) through (iv) and (z)(2)(viii) through (x) of this section, except for internal fuel combustion units that are not compressor-drivers, with a rated heat capacity greater than 1 million Btu per hour (or the equivalent of 130 horsepower) or internal fuel combustion units of any heat capacity that are compressor-drivers that combust natural gas meeting the criteria in § 98.233(z)(1) or (2) or a fuel meeting the criteria in § 98.233(z)(3), which must report the information specified in paragraphs (z)(2)(i) through (x) of this section. Information must be reported for each combustion unit type, fuel type, and method for determining the CH4 emission factor combination, as applicable.

(i) Well-pad ID (for the onshore petroleum and natural gas production industry segment only) or gathering and boosting site ID (for the onshore petroleum and natural gas gathering and boosting industry segment only).

(ii) The type of combustion unit including external fuel combustion units with a rated heat capacity greater than 5 million Btu per hour; internal fuel combustion units that are not compressor-drivers, with a rated heat capacity greater than 1 million Btu per hour (or the equivalent of 130 horsepower); or internal fuel combustion units of any heat capacity that are compressor-drivers.

(iv) The quantity of fuel combusted in the calendar year, in thousand standard cubic feet, gallons, or tons.

(v) The equipment type, including reciprocating 2-stroke-lean burn, reciprocating 4-stroke lean-burn, reciprocating 4-stroke rich-burn, and gas turbine.

(vi) The method used to determine the methane emission factor, including the default emission factor from table W-7 to this subpart, OEM data, or performance tests in § 98.234(i) for natural gas described in § 98.233(z)(1) or (2), or performance tests in § 98.234(i) or default combustion efficiency for fuels described in section § 98.233(z)(3).

(vii) If multiple performance tests were performed in the same reporting year, the arithmetic average value of CH4 emission factor (kg CH4/mmBtu). This information is not required if CH4 emissions were calculated per § 98.233(z)(3)(ii)(D).

(viii) Annual CO2 emissions, in metric tons CO2, calculated according to § 98.233(z)(1) through (3).

(ix) Annual CH4 emissions, in metric tons CH4, calculated according to § 98.233(z)(1) through (3).

(x) Annual N2O emissions, in metric tons N2O, calculated according to § 98.233(z)(1) through (3).

Except as provided in this section, all terms used in this subpart have the same meaning given in the Clean Air Act and subpart A of this part.

(iii) For the components listed in § 98.232(c)(21)(i), (e)(7) and (8), (f)(5) through (8), (g)(4), (g)(6) and (7), (h)(5), (h)(7) and (8), and (j)(10)(i) that are subject to the well site or compressor station fugitive emissions standards in § 60.5397a of this chapter, the fugitive emissions standards for well sites, centralized production facilities, and compressor stations in § 60.5397b or 60.5398b of this chapter, or an applicable approved state plan or applicable Federal plan in part 62 of this chapter, and are required to conduct surveys using any of the leak detection methods in § 98.234(a)(1)(ii) or (iii) or (a)(2)(ii), as applicable, you must use the results of those surveys to calculate equipment leak emissions using the procedures specified in either paragraph (q)(2) or (3) of this section.

(iii) For the components listed in § 98.232(c)(21)(i), (e)(7) and (8), (f)(5) through (8), (g)(4), (g)(6) and (7), (h)(5), (h)(7) and (8), and (j)(10)(i) that are subject to the well site or compressor station fugitive emissions standards in § 60.5397a of this chapter, the fugitive emissions standards for well sites, centralized production facilities, and compressor stations in § 60.5397b or 60.5398b of this chapter, or an applicable approved state plan or applicable Federal plan in part 62 of this chapter, and are required to conduct surveys using any of the leak detection methods in § 98.234(a)(1)(ii) or (iii) or (a)(2)(ii), as applicable, you must use the results of those surveys to calculate equipment leak emissions using the procedures specified in either paragraph (q)(2) or (3) of this section.

(iii) For the components listed in § 98.232(c)(21)(i), (e)(7) and (8), (f)(5) through (8), (g)(4), (g)(6) and (7), (h)(5), (h)(7) and (8), and (j)(10)(i) that are subject to the well site or compressor station fugitive emissions standards in § 60.5397a of this chapter, the fugitive emissions standards for well sites, centralized production facilities, and compressor stations in § 60.5397b or 60.5398b of this chapter, or an applicable approved state plan or applicable Federal plan in part 62 of this chapter, and are required to conduct surveys using any of the leak detection methods in § 98.234(a)(1)(ii) or (iii) or (a)(2)(ii), as applicable, you must use the results of those surveys to calculate equipment leak emissions using the procedures specified in either paragraph (q)(2) or (3) of this section.

(iii) For the components listed in § 98.232(c)(21)(i), (e)(7) and (8), (f)(5) through (8), (g)(4), (g)(6) and (7), (h)(5), (h)(7) and (8), and (j)(10)(i) that are subject to the well site or compressor station fugitive emissions standards in § 60.5397a of this chapter, the fugitive emissions standards for well sites, centralized production facilities, and compressor stations in § 60.5397b or 60.5398b of this chapter, or an applicable approved state plan or applicable Federal plan in part 62 of this chapter, and are required to conduct surveys using any of the leak detection methods in § 98.234(a)(1)(ii) or (iii) or (a)(2)(ii), as applicable, you must use the results of those surveys to calculate equipment leak emissions using the procedures specified in either paragraph (q)(2) or (3) of this section.

(iii) For the components listed in § 98.232(c)(21)(i), (e)(7) and (8), (f)(5) through (8), (g)(4), (g)(6) and (7), (h)(5), (h)(7) and (8), and (j)(10)(i) that are subject to the well site or compressor station fugitive emissions standards in § 60.5397a of this chapter, the fugitive emissions standards for well sites, centralized production facilities, and compressor stations in § 60.5397b or 60.5398b of this chapter, or an applicable approved state plan or applicable Federal plan in part 62 of this chapter, and are required to conduct surveys using any of the leak detection methods in § 98.234(a)(1)(ii) or (iii) or (a)(2)(ii), as applicable, you must use the results of those surveys to calculate equipment leak emissions using the procedures specified in either paragraph (q)(2) or (3) of this section.

(iii) For the components listed in § 98.232(c)(21)(i), (e)(7) and (8), (f)(5) through (8), (g)(4), (g)(6) and (7), (h)(5), (h)(7) and (8), and (j)(10)(i) that are subject to the well site or compressor station fugitive emissions standards in § 60.5397a of this chapter, the fugitive emissions standards for well sites, centralized production facilities, and compressor stations in § 60.5397b or 60.5398b of this chapter, or an applicable approved state plan or applicable Federal plan in part 62 of this chapter, and are required to conduct surveys using any of the leak detection methods in § 98.234(a)(1)(ii) or (iii) or (a)(2)(ii), as applicable, you must use the results of those surveys to calculate equipment leak emissions using the procedures specified in either paragraph (q)(2) or (3) of this section.

(iii) For the components listed in § 98.232(c)(21)(i), (e)(7) and (8), (f)(5) through (8), (g)(4), (g)(6) and (7), (h)(5), (h)(7) and (8), and (j)(10)(i) that are subject to the well site or compressor station fugitive emissions standards in § 60.5397a of this chapter, the fugitive emissions standards for well sites, centralized production facilities, and compressor stations in § 60.5397b or 60.5398b of this chapter, or an applicable approved state plan or applicable Federal plan in part 62 of this chapter, and are required to conduct surveys using any of the leak detection methods in § 98.234(a)(1)(ii) or (iii) or (a)(2)(ii), as applicable, you must use the results of those surveys to calculate equipment leak emissions using the procedures specified in either paragraph (q)(2) or (3) of this section.

(r) This paragraph (r) applies to emissions sources listed in § 98.232(c)(21)(ii), (f)(7), (g)(5), (h)(6), (j)(10)(ii), (m)(3)(i), and (m)(4)(i) if you are not required to comply with paragraph (q) of this section and if you do not elect to comply with paragraph (q) of this section for these components in lieu of this paragraph (r). This paragraph (r) also applies to emission sources listed in § 98.232(i)(2) through (6), (j)(11), and (m)(5). To be subject to the requirements of this paragraph (r), the listed emissions sources also must contact streams with gas content greater than 10 percent CH4 plus CO2 by weight. Emissions sources that contact streams with gas content less than or equal to 10 percent CH4 plus CO2 by weight are exempt from the requirements of this paragraph (r) and do not need to be reported. Tubing systems equal to or less than one half inch diameter are exempt from the requirements of this paragraph (r) and do not need to be reported. Equipment leak components in vacuum service are exempt from the survey and emission estimation requirements of this paragraph (r) and only the count of these equipment must be reported. You must calculate emissions from all emission sources listed in this paragraph (r) using equation W-32A to this section, except for natural gas distribution facility emission sources listed in § 98.232(i)(3). Natural gas distribution facility emission sources listed in § 98.232(i)(3) must calculate emissions using equation W-32B to this section and according to paragraph (r)(6)(ii) of this section.

(1) Calculate both CH4 and CO2 mass emissions from volumetric emissions using calculations in paragraph (v) of this section.

(2) Onshore petroleum and natural gas production facilities and onshore petroleum and natural gas gathering and boosting facilities must use the appropriate default whole gas population emission factors listed in table W-1 to this subpart. Major equipment associated with gas wells are considered gas service equipment in table W-1 to this subpart. Onshore petroleum and natural gas gathering and boosting facilities shall use the gas service equipment emission factors in table W-1 to this subpart. Major equipment associated with crude oil wells are considered crude service equipment in table W-1 to this subpart. Where facilities conduct EOR operations, the emission factor listed in table W-1 to this subpart shall be used to estimate all streams of gases, including recycle CO2 stream. For meters/piping, use one meters/piping per well-pad for onshore petroleum and natural gas production operations and the number of meters in the facility for onshore petroleum and natural gas gathering and boosting operations.

(3) Underground natural gas storage facilities must use the appropriate default total hydrocarbon population emission factors for storage wellheads in gas service listed in table W-3 to this subpart.

(4) LNG storage facilities must use the appropriate default methane population emission factors for LNG storage compressors in gas service listed in table W-5 to this subpart.

(5) LNG import and export facilities must use the appropriate default methane population emission factors for LNG terminal compressors in gas service listed in table W-5 to this subpart.

(6) Natural gas distribution facilities must use the appropriate methane emission factors as described in paragraphs (r)(6)(i) and (ii) of this section.

(i) Below grade transmission-distribution transfer stations, below grade metering-regulating stations, distribution mains, and distribution services must use the appropriate default methane population emission factors listed in table W-5 to this subpart to estimate emissions from components listed in § 98.232(i)(2), (4), (5), and (6), respectively.

(ii) Above grade metering-regulating stations that are not above grade transmission-distribution transfer stations must use the meter/regulator run population emission factor calculated in equation W-31 to this section in accordance with paragraph (q)(2)(x) or (q)(3)(viii)(A) of this section for the components listed in § 98.232(i)(3). Natural gas distribution facilities that do not have above grade transmission-distribution transfer stations are not required to calculate emissions for above grade metering-regulating stations and are not required to report GHG emissions in § 98.236(r)(2)(v).

(7) Onshore natural gas transmission pipeline facilities must use the appropriate default methane population emission factors listed in table W-5 to this subpart to estimate emissions from components listed in § 98.232(m)(3)(i), (4)(i) and (5).

(iii) For the components listed in § 98.232(c)(21)(i), (e)(7) and (8), (f)(5) through (8), (g)(4), (g)(6) and (7), (h)(5), (h)(7) and (8), and (j)(10)(i) that are subject to the well site or compressor station fugitive emissions standards in § 60.5397a of this chapter, the fugitive emissions standards for well sites, centralized production facilities, and compressor stations in § 60.5397b or 60.5398b of this chapter, or an applicable approved state plan or applicable Federal plan in part 62 of this chapter, and are required to conduct surveys using any of the leak detection methods in § 98.234(a)(1)(ii) or (iii) or (a)(2)(ii), as applicable, you must use the results of those surveys to calculate equipment leak emissions using the procedures specified in either paragraph (q)(2) or (3) of this section.

(iii) For the components listed in § 98.232(c)(21)(i), (e)(7) and (8), (f)(5) through (8), (g)(4), (g)(6) and (7), (h)(5), (h)(7) and (8), and (j)(10)(i) that are subject to the well site or compressor station fugitive emissions standards in § 60.5397a of this chapter, the fugitive emissions standards for well sites, centralized production facilities, and compressor stations in § 60.5397b or 60.5398b of this chapter, or an applicable approved state plan or applicable Federal plan in part 62 of this chapter, and are required to conduct surveys using any of the leak detection methods in § 98.234(a)(1)(ii) or (iii) or (a)(2)(ii), as applicable, you must use the results of those surveys to calculate equipment leak emissions using the procedures specified in either paragraph (q)(2) or (3) of this section.

(iii) For the components listed in § 98.232(c)(21)(i), (e)(7) and (8), (f)(5) through (8), (g)(4), (g)(6) and (7), (h)(5), (h)(7) and (8), and (j)(10)(i) that are subject to the well site or compressor station fugitive emissions standards in § 60.5397a of this chapter, the fugitive emissions standards for well sites, centralized production facilities, and compressor stations in § 60.5397b or 60.5398b of this chapter, or an applicable approved state plan or applicable Federal plan in part 62 of this chapter, and are required to conduct surveys using any of the leak detection methods in § 98.234(a)(1)(ii) or (iii) or (a)(2)(ii), as applicable, you must use the results of those surveys to calculate equipment leak emissions using the procedures specified in either paragraph (q)(2) or (3) of this section.

(r) This paragraph (r) applies to emissions sources listed in § 98.232(c)(21)(ii), (f)(7), (g)(5), (h)(6), (j)(10)(ii), (m)(3)(i), and (m)(4)(i) if you are not required to comply with paragraph (q) of this section and if you do not elect to comply with paragraph (q) of this section for these components in lieu of this paragraph (r). This paragraph (r) also applies to emission sources listed in § 98.232(i)(2) through (6), (j)(11), and (m)(5). To be subject to the requirements of this paragraph (r), the listed emissions sources also must contact streams with gas content greater than 10 percent CH4 plus CO2 by weight. Emissions sources that contact streams with gas content less than or equal to 10 percent CH4 plus CO2 by weight are exempt from the requirements of this paragraph (r) and do not need to be reported. Tubing systems equal to or less than one half inch diameter are exempt from the requirements of this paragraph (r) and do not need to be reported. Equipment leak components in vacuum service are exempt from the survey and emission estimation requirements of this paragraph (r) and only the count of these equipment must be reported. You must calculate emissions from all emission sources listed in this paragraph (r) using equation W-32A to this section, except for natural gas distribution facility emission sources listed in § 98.232(i)(3). Natural gas distribution facility emission sources listed in § 98.232(i)(3) must calculate emissions using equation W-32B to this section and according to paragraph (r)(6)(ii) of this section.

(1) Calculate both CH4 and CO2 mass emissions from volumetric emissions using calculations in paragraph (v) of this section.

(2) Onshore petroleum and natural gas production facilities and onshore petroleum and natural gas gathering and boosting facilities must use the appropriate default whole gas population emission factors listed in table W-1 to this subpart. Major equipment associated with gas wells are considered gas service equipment in table W-1 to this subpart. Onshore petroleum and natural gas gathering and boosting facilities shall use the gas service equipment emission factors in table W-1 to this subpart. Major equipment associated with crude oil wells are considered crude service equipment in table W-1 to this subpart. Where facilities conduct EOR operations, the emission factor listed in table W-1 to this subpart shall be used to estimate all streams of gases, including recycle CO2 stream. For meters/piping, use one meters/piping per well-pad for onshore petroleum and natural gas production operations and the number of meters in the facility for onshore petroleum and natural gas gathering and boosting operations.

(3) Underground natural gas storage facilities must use the appropriate default total hydrocarbon population emission factors for storage wellheads in gas service listed in table W-3 to this subpart.

(4) LNG storage facilities must use the appropriate default methane population emission factors for LNG storage compressors in gas service listed in table W-5 to this subpart.

(5) LNG import and export facilities must use the appropriate default methane population emission factors for LNG terminal compressors in gas service listed in table W-5 to this subpart.

(6) Natural gas distribution facilities must use the appropriate methane emission factors as described in paragraphs (r)(6)(i) and (ii) of this section.

(i) Below grade transmission-distribution transfer stations, below grade metering-regulating stations, distribution mains, and distribution services must use the appropriate default methane population emission factors listed in table W-5 to this subpart to estimate emissions from components listed in § 98.232(i)(2), (4), (5), and (6), respectively.

(ii) Above grade metering-regulating stations that are not above grade transmission-distribution transfer stations must use the meter/regulator run population emission factor calculated in equation W-31 to this section in accordance with paragraph (q)(2)(x) or (q)(3)(viii)(A) of this section for the components listed in § 98.232(i)(3). Natural gas distribution facilities that do not have above grade transmission-distribution transfer stations are not required to calculate emissions for above grade metering-regulating stations and are not required to report GHG emissions in § 98.236(r)(2)(v).

(7) Onshore natural gas transmission pipeline facilities must use the appropriate default methane population emission factors listed in table W-5 to this subpart to estimate emissions from components listed in § 98.232(m)(3)(i), (4)(i) and (5).

(iii) For the components listed in § 98.232(c)(21)(i), (e)(7) and (8), (f)(5) through (8), (g)(4), (g)(6) and (7), (h)(5), (h)(7) and (8), and (j)(10)(i) that are subject to the well site or compressor station fugitive emissions standards in § 60.5397a of this chapter, the fugitive emissions standards for well sites, centralized production facilities, and compressor stations in § 60.5397b or 60.5398b of this chapter, or an applicable approved state plan or applicable Federal plan in part 62 of this chapter, and are required to conduct surveys using any of the leak detection methods in § 98.234(a)(1)(ii) or (iii) or (a)(2)(ii), as applicable, you must use the results of those surveys to calculate equipment leak emissions using the procedures specified in either paragraph (q)(2) or (3) of this section.

(iii) For the components listed in § 98.232(c)(21)(i), (e)(7) and (8), (f)(5) through (8), (g)(4), (g)(6) and (7), (h)(5), (h)(7) and (8), and (j)(10)(i) that are subject to the well site or compressor station fugitive emissions standards in § 60.5397a of this chapter, the fugitive emissions standards for well sites, centralized production facilities, and compressor stations in § 60.5397b or 60.5398b of this chapter, or an applicable approved state plan or applicable Federal plan in part 62 of this chapter, and are required to conduct surveys using any of the leak detection methods in § 98.234(a)(1)(ii) or (iii) or (a)(2)(ii), as applicable, you must use the results of those surveys to calculate equipment leak emissions using the procedures specified in either paragraph (q)(2) or (3) of this section.

(a) You must report CO2, CH4, and N2O emissions from each industry segment specified in paragraphs (b) through (j) and (m) of this section, CO2, CH4, and N2O emissions from each flare as specified in paragraphs (b) through (j) of this section, and stationary and portable combustion emissions as applicable as specified in paragraph (k) of this section. You must also report the information specified in paragraph (l) of this section, as applicable.

(p) If you are required to report emissions from reciprocating compressor venting as specified in § 98.232(d)(1), (e)(1), (f)(1), (g)(1), and (h)(1), you must conduct volumetric emission measurements specified in paragraph (p)(1) of this section using methods specified in paragraphs (p)(2) through (5) of this section; perform calculations specified in paragraphs (p)(6) through (9) of this section; and calculate CH4 and CO2 mass emissions as specified in paragraph (p)(11) of this section. If you are required to report emissions from reciprocating compressor venting at an onshore petroleum and natural gas production facility as specified in § 98.232(c)(11) or an onshore petroleum and natural gas gathering and boosting facility as specified in § 98.232(j)(9), you must calculate volumetric emissions as specified in paragraph (p)(10) of this section and calculate CH4 and CO2 mass emissions as specified in paragraph (p)(11) of this section. If emissions from a compressor source are routed to a flare, paragraphs (p)(1) through (11) of this section do not apply and instead you must calculate CH4, CO2, and N2O emissions as specified in paragraph (n) of this section and report emissions from the flare as specified in § 98.236(n). If emissions from a compressor source are routed to combustion, paragraphs (p)(1) through (11) of this section do not apply and instead you must calculate and report emissions as specified in subpart C of this part or paragraph (z) of this section, as applicable. If emissions from a compressor source are routed to a vapor recovery system, paragraphs (p)(1) through (11) of this section do not apply.

(1) You must conduct volumetric emission measurements on each reciprocating compressor as specified in this paragraph. Compressor sources (as defined in § 98.238) without manifolded vents must use a measurement method specified in paragraph (p)(1)(i) or (ii) of this section. Manifolded compressor sources (as defined in § 98.238) must use a measurement method specified in paragraph (p)(1)(i), (ii), (iii), or (iv) of this section.

(i) Measure venting from each compressor according to either paragraph (p)(1)(i)(A), (B), or (C) of this section at least once annually, based on the compressor mode (as defined in § 98.238) in which the compressor was found at the time of measurement, except as specified in paragraph (p)(1)(i)(D) of this section. If additional measurements beyond the required annual testing are performed (including duplicate measurements or measurement of additional operating modes), then all measurements satisfying the applicable monitoring and QA/QC that is required by this paragraph (p) must be used in the calculations specified in this section.

(A) For a compressor measured in operating-mode, you must measure volumetric emissions from blowdown valve leakage through the blowdown vent as specified in paragraph (p)(2)(i) of this section, and measure volumetric emissions from reciprocating rod packing as specified in paragraph (p)(2)(ii) or (iii) of this section, as applicable.

(B) For a compressor measured in not-operating-depressurized-mode, you must measure volumetric emissions from isolation valve leakage as specified in paragraph (p)(2)(i) of this section. If a compressor is not operated and has blind flanges in place throughout the reporting period, measurement is not required in this compressor mode.

(C) For a compressor measured in standby-pressurized-mode, you must measure volumetric emissions from blowdown valve leakage through the blowdown vent as specified in paragraph (p)(2)(i) of this section and measure volumetric emissions from reciprocating rod packing as specified in paragraph (p)(2)(ii) or (iii) of this section, as applicable.

(D) An annual as found measurement is not required in the first year of operation for any new compressor that begins operation after as found measurements have been conducted for all existing compressors. For only the first year of operation of new compressors, calculate emissions according to paragraph (p)(6)(ii) of this section.

(ii) Instead of measuring the compressor source according to paragraph (p)(1)(i) of this section for a given compressor, you may elect to continuously measure volumetric emissions from a compressor source as specified in paragraph (p)(3) of this section.

(iii) For a compressor source that is part of a manifolded group of compressor sources (as defined in § 98.238), instead of measuring the compressor source according to paragraph (p)(1)(i), (ii), or (iv) of this section, you may elect to measure combined volumetric emissions from the manifolded group of compressor sources by conducting measurements at the common vent stack as specified in paragraph (p)(4) of this section. The measurements must be conducted at the frequency specified in paragraphs (p)(1)(iii)(A) and (B) of this section.

(A) A minimum of one measurement must be taken for each manifolded group of compressor sources in a calendar year.

(B) The measurement may be performed while the compressors are in any compressor mode.

(iv) For a compressor source that is part of a manifolded group of compressor sources, instead of measuring the compressor source according to paragraph (p)(1)(i), (ii), or (iii) of this section, you may elect to continuously measure combined volumetric emissions from the manifolded group of compressors sources as specified in paragraph (p)(5) of this section.

(2) . If conducting measurements for each compressor source, you must determine the volumetric emissions from blowdown valves and isolation valves as specified in paragraph (p)(2)(i) of this section. You must determine the volumetric emissions from reciprocating rod packing as specified in paragraph (p)(2)(ii) or (iii) of this section, as applicable.

(i) and for isolation valves on compressors in not-operating-depressurized-mode, determine the volumetric emissions using one of the methods specified in paragraphs (p)(2)(i)(A) through (D) of this section.

(A) Determine the volumetric flow at standard conditions from the blowdown vent using calibrated bagging or high volume sampler according to methods set forth in § 98.234(c) and (d), respectively.

(B) Determine the volumetric flow at standard conditions from the blowdown vent using a temporary meter such as a vane anemometer, according to methods set forth in § 98.234(b).

(C) Use an acoustic leak detection device according to methods set forth in § 98.234(a)(5).

(D) You may choose to use any of the methods set forth in § 98.234(a) to screen for emissions. If emissions are detected using the methods set forth in § 98.234(a), then you must use one of the methods specified in paragraphs (p)(2)(i)(A) through (C) of this section. If emissions are not detected using the methods in § 98.234(a), then you may assume that the volumetric emissions are zero. For the purposes of this paragraph, when using any of the methods in § 98.234(a), emissions are detected whenever a leak is detected according to the method.

(ii) For reciprocating rod packing equipped with an open-ended vent line on compressors in operating-mode or standby-pressurized-mode, determine the volumetric emissions using one of the methods specified in paragraphs (p)(2)(ii)(A) through (C) of this section.

(A) Determine the volumetric flow at standard conditions from the open-ended vent line using calibrated bagging or high volume sampler according to methods set forth in § 98.234(c) and (d), respectively.

(B) Determine the volumetric flow at standard conditions from the open-ended vent line using a temporary meter such as a vane anemometer, according to methods set forth in § 98.234(b).

(C) You may choose to use any of the methods set forth in § 98.234(a)(1) through (3) to screen for emissions. If emissions are detected using one of these specified methods, then you must use one of the methods specified in paragraphs (p)(2)(ii)(A) and (B) of this section. If emissions are not detected using the methods in § 98.234(a)(1) through (3), then you may assume that the volumetric emissions are zero. For the purposes of this paragraph (p)(2)(ii)(C), when using any of the methods in § 98.234(a), emissions are detected whenever a leak is detected according to the method. Acoustic leak detection is only applicable for through-valve leakage and is not applicable for screening or measuring rod packing emissions.

(iii) For reciprocating rod packing not equipped with an open-ended vent line on compressors in operating-mode, you must determine the volumetric emissions using the method specified in paragraphs (p)(2)(iii)(A) and (B) of this section.

(A) You must use the methods described in § 98.234(a)(1) through (3) to conduct annual leak detection of equipment leaks from the packing case into an open distance piece, or for compressors with a closed distance piece, conduct annual detection of gas emissions from the rod packing vent, distance piece vent, compressor crank case breather cap, or other vent emitting gas from the rod packing. Acoustic leak detection is only applicable for through-valve leakage and is not applicable for screening rod packing emissions.

(B) You must measure emissions found in paragraph (p)(2)(iii)(A) of this section using an appropriate meter, calibrated bag, or high volume sampler according to methods set forth in § 98.234(b), (c), and (d), respectively.

(3) . If you elect to conduct continuous volumetric emission measurements for an individual compressor source as specified in paragraph (p)(1)(ii) of this section, you must measure volumetric emissions as specified in paragraphs (p)(3)(i) and (p)(3)(ii) of this section.

(i) Continuously measure the volumetric flow for the individual compressor sources at standard conditions using a permanent meter according to methods set forth in § 98.234(b).

(ii) If compressor blowdown emissions are included in the metered emissions specified in paragraph (p)(3)(i) of this section, the compressor blowdown emissions may be included with the reported emissions for the compressor source and do not need to be calculated separately using the method specified in paragraph (i) of this section for blowdown vent stacks.

(4) . If conducting measurements for a manifolded group of compressor sources, you must measure volumetric emissions as specified in paragraphs (p)(4)(i) and (ii) of this section.

(i) Measure at a single point in the manifold downstream of all compressor inputs and, if practical, prior to comingling with other non-compressor emission sources.

(ii) Determine the volumetric flow at standard conditions from the common stack using one of the methods specified in paragraphs (p)(4)(ii)(A) through (F) of this section.

(A) A temporary meter such as a vane anemometer according to methods set forth in § 98.234(b).

(B) Calibrated bagging according to methods set forth in § 98.234(c).

(C) A high volume sampler according to methods set forth in § 98.234(d).

(D) [Reserved]

(E) You may choose to use any of the methods set forth in § 98.234(a)(1) through (3) to screen for emissions. If emissions are detected using one of these specified methods, then you must use one of the methods specified in paragraphs (p)(4)(ii)(A) through (D) of this section. If emissions are not detected using the methods in § 98.234(a)(1) through (3), then you may assume that the volumetric emissions are zero. For the purposes of this paragraph, when using any of the methods in § 98.234(a), emissions are detected whenever a leak is detected according to the method. Acoustic leak detection is only applicable for through-valve leakage and is not applicable for screening a manifolded group of compressor sources.

(F) If one of the screening methods specified in § 98.234(a)(1) through (3) identifies a leak in a manifolded group of reciprocating compressor sources, you may use acoustic leak detection, according to § 98.234(a)(5), to identify the source of the leak. You must use one of the methods specified in paragraphs (p)(4)(ii)(A) through (D) of this section to quantify the emissions from the identified source.

(5) . If you elect to conduct continuous volumetric emission measurements for a manifolded group of compressor sources as specified in paragraph (p)(1)(iv) of this section, you must measure volumetric emissions as specified in paragraphs (p)(5)(i) through (iii) of this section.

(i) Measure at a single point in the manifold downstream of all compressor inputs and, if practical, prior to comingling with other non-compressor emission sources.

(ii) Continuously measure the volumetric flow for the manifolded group of compressor sources at standard conditions using a permanent meter according to methods set forth in § 98.234(b).

(iii) If compressor blowdown emissions are included in the metered emissions specified in paragraph (p)(5)(ii) of this section, the compressor blowdown emissions may be included with the reported emissions for the manifolded group of compressor sources and do not need to be calculated separately using the method specified in paragraph (i) of this section for blowdown vent stacks.

(6) . For compressor sources measured according to paragraph (p)(1)(i) of this section, you must calculate GHG emissions from the compressor sources as specified in paragraphs (p)(6)(i) through (iv) of this section.

(i) Using equation W-26 to this section, calculate the annual volumetric GHG emissions for each reciprocating compressor mode-source combination specified in paragraphs (p)(1)(i)(A) through (C) of this section that was measured during the reporting year.

(ii) Using equation W-27 to this section, calculate the annual volumetric GHG emissions from each reciprocating compressor mode-source combination specified in paragraphs (p)(1)(i)(A) through (C) of this section that was not measured during the reporting year.

(iii) Using equation W-28 to this section, develop an emission factor for each compressor mode-source combination specified in paragraphs (p)(1)(i)(A) through (C) of this section. These emission factors must be calculated annually and used in equation W-27 to this section to determine volumetric emissions from a reciprocating compressor in the mode-source combinations that were not measured in the reporting year.

(iv) The reporter emission factor in equation W-28 to this section may be calculated by using all measurements from a single owner or operator instead of only using measurements from a single facility. If you elect to use this option, the reporter emission factor must be applied to all reporting facilities for the owner or operator.

(7) . For compressor sources measured according to paragraph (p)(1)(ii) of this section, you must use the continuous volumetric emission measurements taken as specified in paragraph (p)(3) of this section and calculate annual volumetric GHG emissions associated with the compressor source using equation W-29A to this section.

(8) For manifolded groups of compressor sources measured according to paragraph (p)(1)(iii) of this section, you must calculate annual GHG emissions using equation W-29B to this section. If the reciprocating compressors included in the manifolded group of compressor sources share the manifold with centrifugal compressors, you must follow the procedures in either this paragraph (p)(8) or paragraph (o)(8) of this section to calculate emissions from the manifolded group of compressor sources.

(9) . For a manifolded group of compressor sources measured according to paragraph (p)(1)(iv) of this section, you must use the continuous volumetric emission measurements taken as specified in paragraph (p)(5) of this section and calculate annual volumetric GHG emissions associated with each manifolded group of compressor sources using equation W-29C to this section. If the reciprocating compressors included in the manifolded group of compressor sources share the manifold with centrifugal compressors, you must follow the procedures in either this paragraph (p)(9) or paragraph (o)(9) of this section to calculate emissions from the manifolded group of compressor sources.

(10) . You must calculate volumetric emissions from reciprocating compressors at an onshore petroleum and natural gas production facility or an onshore petroleum and natural gas gathering and boosting facility as specified in paragraphs (p)(10)(i) through (iv) of this section, as applicable.

(i) For all reciprocating compressors at an onshore petroleum and natural gas production facility or an onshore petroleum and natural gas gathering and boosting facility that are subject to the reciprocating compressor standards in § 60.5385b of this chapter or an applicable approved state plan or applicable Federal plan in part 62 of this chapter, you must conduct the volumetric emission measurements as required by § 60.5385b(b) and (c) of this chapter or an applicable approved state plan or applicable Federal plan in part 62 of this chapter, conduct any additional volumetric emission measurements specified in paragraph (p)(1) of this section using methods specified in paragraphs (p)(2) through (5) of this section (based on the compressor mode (as defined in § 98.238) in which the compressor was found at the time of measurement), and calculate emissions as specified in paragraphs (p)(6) through (9) of this section. Conduct all measurements required by this paragraph (p)(10)(i) at the frequency specified by § 60.5385b(a) of this chapter or an applicable approved state plan or applicable Federal plan in part 62 of this chapter. For any reporting year in which measuring at the frequency specified by § 60.5385b(a) of this chapter results in measurement not being required for a subject compressor, calculate emissions for all mode-source combinations as specified in paragraph (p)(6)(ii) of this section.

(ii) For all reciprocating compressors at an onshore petroleum and natural gas production facility or an onshore petroleum and natural gas gathering and boosting facility that are not subject to the reciprocating compressor standards in § 60.5385b of this chapter or an applicable approved state plan or applicable Federal plan in part 62 of this chapter, you may elect to conduct volumetric emission measurements specified in paragraph (p)(1) of this section using methods specified in paragraphs (p)(2) through (5) of this section (based on the compressor mode (as defined in § 98.238) in which the compressor was found at the time of measurement), and calculate emissions as specified in paragraphs (p)(6) through (9) of this section.

(iii) For all reciprocating compressors at an onshore petroleum and natural gas production facility or an onshore petroleum and natural gas gathering and boosting facility for which paragraph (p)(10)(i) of this section does not apply, and you do not elect to conduct volumetric emission measurements specified in paragraph (p)(1) of this section, you must calculate total atmospheric rod packing emissions from all reciprocating compressors at either an onshore petroleum and natural gas production facility or an onshore petroleum and natural gas gathering and boosting facility using equation W-29D to this section. Reciprocating compressor rod packing emissions that are routed to a flare, combustion, or vapor recovery system are not required to be determined under this paragraph (p).

(iv) For all reciprocating compressors at an onshore petroleum and natural gas production facility or an onshore petroleum and natural gas gathering and boosting facility for which paragraph (p)(10)(i) of this section does not apply, you must calculate rod packing vent emissions from each reciprocating compressor using equation W-29E to this section. Reciprocating compressor rod packing emissions that are routed to a flare, combustion, or vapor recovery system are not required to be determined under this paragraph (p).

(11) You must calculate both CH4 and CO2 mass emissions from volumetric emissions using calculations in paragraph (v) of this section.

(o) If you are required to report emissions from centrifugal compressor venting as specified in § 98.232(d)(2), (e)(2), (f)(2), (g)(2), and (h)(2), you must conduct volumetric emission measurements specified in paragraph (o)(1) of this section using methods specified in paragraphs (o)(2) through (5) of this section; perform calculations specified in paragraphs (o)(6) through (9) of this section; and calculate CH4 and CO2 mass emissions as specified in paragraph (o)(11) of this section. If you are required to report emissions from centrifugal compressor venting at an onshore petroleum and natural gas production facility as specified in § 98.232(c)(19) or an onshore petroleum and natural gas gathering and boosting facility as specified in § 98.232(j)(8), you must calculate volumetric emissions as specified in paragraph (o)(10) of this section and calculate CH4 and CO2 mass emissions as specified in paragraph (o)(11) of this section. If emissions from a compressor source are routed to a flare, paragraphs (o)(1) through (11) of this section do not apply and instead you must calculate CH4, CO2, and N2O emissions as specified in paragraph (n) of this section and report emissions from the flare as specified in § 98.236(n). If emissions from a compressor source are routed to combustion, paragraphs (o)(1) through (11) of this section do not apply and instead you must calculate and report emissions as specified in subpart C of this part or paragraph (z) of this section, as applicable. If emissions from a compressor source are routed to a vapor recovery system, paragraphs (o)(1) through (11) of this section do not apply.

(1) You must conduct volumetric emission measurements on each centrifugal compressor as specified in this paragraph. Compressor sources (as defined in § 98.238) without manifolded vents must use a measurement method specified in paragraph (o)(1)(i) or (ii) of this section. Manifolded compressor sources (as defined in § 98.238) must use a measurement method specified in paragraph (o)(1)(i), (ii), (iii), or (iv) of this section.

(i) Measure venting from each compressor according to either paragraph (o)(1)(i)(A), (B), or (C) of this section at least once annually, based on the compressor mode (as defined in § 98.238) in which the compressor was found at the time of measurement, except as specified in paragraph (o)(1)(i)(D) of this section. If additional measurements beyond the required annual testing are performed (including duplicate measurements or measurement of additional operating modes), then all measurements satisfying the applicable monitoring and QA/QC that is required by this paragraph (o) must be used in the calculations specified in this section.

(A) For a compressor measured in operating-mode, you must measure volumetric emissions from blowdown valve leakage through the blowdown vent as specified in paragraph (o)(2)(i) of this section, measure volumetric emissions from wet seal oil degassing vents as specified in paragraph (o)(2)(ii) of this section if the compressor has wet seal oil degassing vents, and measure volumetric emissions from dry seal vents as specified in paragraph (o)(2)(iii) of this section if the compressor has dry seals.

(B) For a compressor measured in not-operating-depressurized-mode, you must measure volumetric emissions from isolation valve leakage as specified in paragraph (o)(2)(i) of this section. If a compressor is not operated and has blind flanges in place throughout the reporting period, measurement is not required in this compressor mode.

(C) For a compressor measured in standby-pressurized-mode, you must measure volumetric emissions from blowdown valve leakage through the blowdown vent as specified in paragraph (o)(2)(i) of this section, measure volumetric emissions from wet seal oil degassing vents as specified in paragraph (o)(2)(ii) of this section if the compressor has wet seal oil degassing vents, and measure volumetric emissions from dry seal vents as specified in paragraph (o)(2)(iii) of this section if the compressor has dry seals.

(D) An annual as found measurement is not required in the first year of operation for any new compressor that begins operation after as found measurements have been conducted for all existing compressors. For only the first year of operation of new compressors, calculate emissions according to paragraph (o)(6)(ii) of this section.

(ii) Instead of measuring the compressor source according to paragraph (o)(1)(i) of this section for a given compressor, you may elect to continuously measure volumetric emissions from a compressor source as specified in paragraph (o)(3) of this section.

(iii) For a compressor source that is part of a manifolded group of compressor sources (as defined in § 98.238), instead of measuring the compressor source according to paragraph (o)(1)(i), (ii), or (iv) of this section, you may elect to measure combined volumetric emissions from the manifolded group of compressor sources by conducting measurements at the common vent stack as specified in paragraph (o)(4) of this section. The measurements must be conducted at the frequency specified in paragraphs (o)(1)(iii)(A) and (B) of this section.

(A) A minimum of one measurement must be taken for each manifolded group of compressor sources in a calendar year.

(B) The measurement may be performed while the compressors are in any compressor mode.

(iv) For a compressor source that is part of a manifolded group of compressor sources, instead of measuring the compressor source according to paragraph (o)(1)(i), (ii), or (iii) of this section, you may elect to continuously measure combined volumetric emissions from the manifolded group of compressor sources as specified in paragraph (o)(5) of this section.

(2) . If conducting measurements for each compressor source, you must determine the volumetric emissions from blowdown valves and isolation valves as specified in paragraph (o)(2)(i) of this section, the volumetric emissions from wet seal oil degassing vents as specified in paragraph (o)(2)(ii) of this section, and the volumetric emissions from dry seal vents as specified in paragraph (o)(2)(iii) of this section.

(i) For blowdown valves on compressors in operating-mode or in standby-pressurized-mode and for isolation valves on compressors in not-operating-depressurized-mode, determine the volumetric emissions using one of the methods specified in paragraphs (o)(2)(i)(A) through (D) of this section.

(A) Determine the volumetric flow at standard conditions from the blowdown vent using calibrated bagging or high volume sampler according to methods set forth in § 98.234(c) and § 98.234(d), respectively.

(B) Determine the volumetric flow at standard conditions from the blowdown vent using a temporary meter such as a vane anemometer according to methods set forth in § 98.234(b).

(C) Use an acoustic leak detection device according to methods set forth in § 98.234(a)(5).

(D) You may choose to use any of the methods set forth in § 98.234(a) to screen for emissions. If emissions are detected using the methods set forth in § 98.234(a), then you must use one of the methods specified in paragraph (o)(2)(i)(A) through (C) of this section. If emissions are not detected using the methods in § 98.234(a), then you may assume that the volumetric emissions are zero. For the purposes of this paragraph, when using any of the methods in § 98.234(a), emissions are detected whenever a leak is detected according to the methods.

(ii) For wet seal oil degassing vents in operating-mode or in standby-pressurized-mode, determine volumetric flow at standard conditions, using one of the methods specified in paragraphs (o)(2)(ii)(A) through (C) of this section. You must quantitatively measure the volumetric flow for wet seal oil degassing vent; you may not use screening methods set forth in § 98.234(a) to screen for emissions for the wet seal oil degassing vent.

(A) Use a temporary meter such as a vane anemometer or permanent flow meter according to methods set forth in § 98.234(b).

(B) Use calibrated bags according to methods set forth in § 98.234(c).

(C) Use a high volume sampler according to methods set forth in § 98.234(d).

(iii) For dry seal vents in operating-mode or in standby-pressurized-mode, determine volumetric flow at standard conditions from each dry seal vent using one of the methods specified in paragraphs (o)(2)(iii)(A) through (D) of this section. The measurement should be conducted on the compressor side dry seal. If a compressor has more than one dry seal vent, determine the aggregate dry seal vent volumetric flow for the compressor as the sum of the volumetric flows determined for each dry seal vent on the compressor.

(A) Use a temporary meter such as a vane anemometer or permanent flow meter according to methods set forth in § 98.234(b).

(B) Use calibrated bags according to methods set forth in § 98.234(c).

(C) Use a high volume sampler according to methods set forth in § 98.234(d).

(D) You may choose to use any of the methods set forth in § 98.234(a)(1) through (3) to screen for emissions. If emissions are detected using one of these specified methods, then you must use one of the methods specified in paragraph (o)(2)(iii)(A) through (C) of this section. If emissions are not detected using the methods in § 98.234(a)(1) through (3), then you may assume that the volumetric emissions are zero. For the purposes of this paragraph, when using any of the methods in § 98.234(a), emissions are detected whenever a leak is detected according to the methods. Acoustic leak detection is only applicable for through-valve leakage and is not applicable for screening dry seal vents.

(3) If you elect to conduct continuous volumetric emission measurements for an individual compressor source as specified in paragraph (o)(1)(ii) of this section, you must measure volumetric emissions as specified in paragraphs (o)(3)(i) and (ii) of this section.

(i) Continuously measure the volumetric flow for the individual compressor source at standard conditions using a permanent meter according to methods set forth in § 98.234(b).

(ii) If compressor blowdown emissions are included in the metered emissions specified in paragraph (o)(3)(i) of this section, the compressor blowdown emissions may be included with the reported emissions for the compressor source and do not need to be calculated separately using the method specified in paragraph (i) of this section for blowdown vent stacks.

(4) If conducting measurements for a manifolded group of compressor sources, you must measure volumetric emissions as specified in paragraphs (o)(4)(i) and (ii) of this section.

(i) Measure at a single point in the manifold downstream of all compressor inputs and, if practical, prior to comingling with other non-compressor emission sources.

(ii) Determine the volumetric flow at standard conditions from the common stack using one of the methods specified in paragraphs (o)(4)(ii)(A) through (F) of this section.

(A) A temporary meter such as a vane anemometer according the methods set forth in § 98.234(b).

(B) Calibrated bagging according to methods set forth in § 98.234(c).

(C) A high volume sampler according to methods set forth § 98.234(d).

(D) [Reserved]

(E) You may choose to use any of the methods set forth in § 98.234(a)(1) through (3) to screen for emissions. If emissions are detected using one of these methods, then you must use one of the methods specified in paragraph (o)(4)(ii)(A) through (D) of this section. If emissions are not detected using the methods in § 98.234(a)(1) through (3), then you may assume that the volumetric emissions are zero. For the purposes of this paragraph, when using any of the methods in § 98.234(a), emissions are detected whenever a leak is detected according to the method. Acoustic leak detection is only applicable for through-valve leakage and is not applicable for screening a manifolded group of compressor sources.

(F) If one of the screening methods specified in § 98.234(a)(1) through (3) identifies a leak in a manifolded group of centrifugal compressor sources, you may use acoustic leak detection, according to § 98.234(a)(5), to identify the source of the leak. You must use one of the methods specified in paragraphs (o)(4)(ii)(A) through (D) of this section to quantify emissions from the identified source.

(5) If you elect to conduct continuous volumetric emission measurements for a manifolded group of compressor sources as specified in paragraph (o)(1)(iv) of this section, you must measure volumetric emissions as specified in paragraphs (o)(5)(i) through (iii) of this section.

(i) Measure at a single point in the manifold downstream of all compressor inputs and, if practical, prior to comingling with other non-compressor emission sources.

(ii) Continuously measure the volumetric flow for the manifolded group of compressor sources at standard conditions using a permanent meter according to methods set forth in § 98.234(b).

(iii) If compressor blowdown emissions are included in the metered emissions specified in paragraph (o)(5)(ii) of this section, the compressor blowdown emissions may be included with the reported emissions for the manifolded group of compressor sources and do not need to be calculated separately using the method specified in paragraph (i) of this section for blowdown vent stacks.

(6) . For compressor sources measured according to paragraph (o)(1)(i) of this section, you must calculate annual GHG emissions from the compressor sources as specified in paragraphs (o)(6)(i) through (iv) of this section.

(i) Using equation W-21 to this section, calculate the annual volumetric GHG emissions for each centrifugal compressor mode-source combination specified in paragraphs (o)(1)(i)(A) through (C) of this section that was measured during the reporting year.

(ii) Using equation W-22 to this section, calculate the annual volumetric GHG emissions from each centrifugal compressor mode-source combination specified in paragraphs (o)(1)(i)(A) through (C) of this section that was not measured during the reporting year.

(iii) Using equation W-23 to this section, develop an emission factor for each compressor mode-source combination specified in paragraphs (o)(1)(i)(A) through (C) of this section. These emission factors must be calculated annually and used in equation W-22 to this section to determine volumetric emissions from a centrifugal compressor in the mode- source combinations that were not measured in the reporting year.

(iv) The reporter emission factor in equation W-23 to this section may be calculated by using all measurements from a single owner or operator instead of only using measurements from a single facility. If you elect to use this option, the reporter emission factor must be applied to all reporting facilities for the owner or operator.

(7) . For compressor sources measured according to paragraph (o)(1)(ii) of this section, you must use the continuous volumetric emission measurements taken as specified in paragraph (o)(3) of this section and calculate annual volumetric GHG emissions associated with the compressor source using equation W-24A to this section.

(8) . For manifolded groups of compressor sources measured according to paragraph (o)(1)(iii) of this section, you must calculate annual volumetric GHG emissions using equation W-24B to this section. If the centrifugal compressors included in the manifolded group of compressor sources share the manifold with reciprocating compressors, you must follow the procedures in either this paragraph (o)(8) or paragraph (p)(8) of this section to calculate emissions from the manifolded group of compressor sources.

(9) For a manifolded group of compressor sources measured according to paragraph (o)(1)(iv) of this section, you must use the continuous volumetric emission measurements taken as specified in paragraph (o)(5) of this section and calculate annual volumetric GHG emissions associated with each manifolded group of compressor sources using equation W-24C to this section. If the centrifugal compressors included in the manifolded group of compressor sources share the manifold with reciprocating compressors, you must follow the procedures in either this paragraph (o)(9) or paragraph (p)(9) of this section to calculate emissions from the manifolded group of compressor sources.

(10) You must calculate volumetric emissions from centrifugal compressors at an onshore petroleum and natural gas production facility or an onshore petroleum and natural gas gathering and boosting facility as specified in paragraphs (o)(10)(i) through (iv), as applicable.

(i) For all centrifugal compressors at an onshore petroleum and natural gas production facility or an onshore petroleum and natural gas gathering and boosting facility that are subject to the centrifugal compressor standards in § 60.5380b of this chapter or an applicable approved state plan or applicable Federal plan in part 62 of this chapter for dry seals and self-contained wet seals, you must conduct the volumetric emission measurements as required by § 60.5380b(a)(5) of this chapter or an applicable approved state plan or applicable Federal plan in part 62 of this chapter, conduct all additional volumetric emission measurements specified in paragraph (o)(1) of this section using methods specified in paragraphs (o)(2) through (5) of this section (based on the compressor mode (as defined in § 98.238) in which the compressor was found at the time of measurement), and calculate emissions as specified in paragraphs (o)(6) through (9) of this section. Conduct all measurements required by this paragraph (o)(10)(i) at the frequency specified by § 60.5380b(a)(4) of this chapter or an applicable approved state plan or applicable Federal plan in part 62 of this chapter. For any reporting year in which measuring at the frequency specified by § 60.5380b(a)(4) of this chapter results in measurement not being required for a subject compressor, calculate emissions for all mode-source combinations as specified in paragraph (o)(6)(ii) of this section.

(ii) For all centrifugal compressors at an onshore petroleum and natural gas production facility or an onshore petroleum and natural gas gathering and boosting facility that are not subject to the centrifugal compressor standards in § 60.5380b of this chapter or an applicable approved state plan or applicable Federal plan in part 62 of this chapter for dry seals and self-contained wet seals, you may elect to conduct the volumetric emission measurements specified in paragraph (o)(1) of this section using methods specified in paragraphs (o)(2) through (5) of this section (based on the compressor mode (as defined in § 98.238) in which the compressor was found at the time of measurement), and calculate emissions as specified in paragraphs (o)(6) through (9) of this section.

(iii) For all centrifugal compressors at an onshore petroleum and natural gas production facility or an onshore petroleum and natural gas gathering and boosting facility for which paragraph (o)(10)(i) of this section does not apply and you do not elect to conduct the volumetric measurements specified in paragraph (o)(1) of this section, you must calculate total atmospheric wet seal oil degassing vent emissions from all centrifugal compressors at either an onshore petroleum and natural gas production facility or an onshore petroleum and natural gas gathering and boosting facility using equation W-25A to this section. Emissions from centrifugal compressor wet seal oil degassing vents that are routed to a flare, combustion, or vapor recovery system are not required to be determined under this paragraph (o).

(iv) For all centrifugal compressors at an onshore petroleum and natural gas production facility or an onshore petroleum and natural gas gathering and boosting facility for which paragraph (o)(10)(i) of this section does not apply, and you do not elect to conduct the volumetric measurements specified in paragraph (o)(1) of this section, you must calculate wet seal oil degassing vent emissions from each centrifugal compressor using equation W-25B to this section. Emissions from centrifugal compressor wet seal oil degassing vents that are routed to a flare, combustion, or vapor recovery system are not required to be determined under this paragraph (o).

(11) . You must calculate both CH4 and CO2 mass emissions from volumetric emissions using calculations in paragraph (v) of this section.

(v) For the components listed in § 98.232(d)(7), you must conduct surveys as specified in paragraphs (q)(1)(v)(A) and (B) of this section and you must calculate equipment leak emissions using the procedures specified in either paragraph (q)(2) or (3) of this section.

(A) For the components listed in § 98.232(d)(7) that are not subject to the equipment leak standards for onshore natural gas processing plants in § 60.5400b or § 60.5401b of this chapter, or an applicable approved state plan or applicable Federal plan in part 62 of this chapter, you may use any of the leak detection methods listed in § 98.234(a).

(B) For the components listed in § 98.232(d)(7) that are subject to the equipment leak standards for onshore natural gas processing plants in § 60.5400b or § 60.5401b of this chapter, or an applicable approved state plan or applicable Federal plan in part 62 of this chapter, you must use either of the leak detection methods in § 98.234(a)(1)(iii) or (a)(2)(ii).

(2) You must indicate whether your facility contains any of the component types subject to or complying with § 98.233(q) that are listed in § 98.232(c)(21), (d)(7), (e)(7) or (8), (f)(5) through (8), (g)(4), (g)(6) or (7), (h)(5), (h)(7) or (8), (i)(1), (j)(10), (m)(3)(ii) or (m)(4)(ii) for your facility's industry segment. For each component type and leak detection method combination that is located at your well-pad site, gathering and boosting site, or facility, you must report the information specified in paragraphs (q)(2)(i) through (ix) of this section. If a component type is located at your well-pad site, gathering and boosting site, or facility and no leaks were identified from that component, then you must report the information in paragraphs (q)(2)(i) through (ix) of this section but report a zero (“0”) for the information required according to paragraphs (q)(2)(vi) through (ix) of this section. If you used Calculation Method 1 (leaker factor emission calculation methodology) for some complete leak surveys and used Calculation Method 2 (leaker measurement methodology) for some complete leak surveys, you must report the information specified in paragraphs (q)(2)(i) through (ix) of this section separately for component surveys using Calculation Method 1 and Calculation Method 2.

(i) Well-pad ID (for the onshore petroleum and natural gas production industry segment only) or gathering and boosting site ID (for the onshore petroleum and natural gas gathering and boosting industry segment only).

(iii) Leak detection method used for the screening survey (e.g., Method 21 as specified in § 98.234(a)(2)(i); Method 21 as specified in § 98.234(a)(2)(ii); and OGI and other leak detection methods as specified in § 98.234(a)(1), (3), or (5)).

(iv) Emission factor or measurement method used (e.g., default emission factor; facility-specific emission factor developed according to § 98.233(q)(4); or direct measurement according to § 98.233(q)(3)).

(vi) Total number of the surveyed component types by leak detection method that were identified as leaking in the calendar year (“xp” in equation W-30 to § 98.233 for the component type or the number of leaks measured for the specified component type according to the provisions in § 98.233(q)(3)).

(vii) Average time the surveyed components are assumed to be leaking and operational, in hours (average of “Tp,z” from equation W-30 to § 98.233 for the component type or average duration of leaks for the specified component type determined according to the provisions in § 98.233(q)(3)(ii)).

(viii) Annual CO2 emissions, in metric tons CO2, for the component type as calculated using equation W-30 to § 98.233 or § 98.233(q)(3)(vii) (for surveyed components only).

(ix) Annual CH4 emissions, in metric tons CH4, for the component type as calculated using equation W-30 to § 98.233 or § 98.233(q)(3)(vii) (for surveyed components only).

(a) You must report CO2, CH4, and N2O emissions from each industry segment specified in paragraphs (b) through (j) and (m) of this section, CO2, CH4, and N2O emissions from each flare as specified in paragraphs (b) through (j) of this section, and stationary and portable combustion emissions as applicable as specified in paragraph (k) of this section. You must also report the information specified in paragraph (l) of this section, as applicable.

(p) If you are required to report emissions from reciprocating compressor venting as specified in § 98.232(d)(1), (e)(1), (f)(1), (g)(1), and (h)(1), you must conduct volumetric emission measurements specified in paragraph (p)(1) of this section using methods specified in paragraphs (p)(2) through (5) of this section; perform calculations specified in paragraphs (p)(6) through (9) of this section; and calculate CH4 and CO2 mass emissions as specified in paragraph (p)(11) of this section. If you are required to report emissions from reciprocating compressor venting at an onshore petroleum and natural gas production facility as specified in § 98.232(c)(11) or an onshore petroleum and natural gas gathering and boosting facility as specified in § 98.232(j)(9), you must calculate volumetric emissions as specified in paragraph (p)(10) of this section and calculate CH4 and CO2 mass emissions as specified in paragraph (p)(11) of this section. If emissions from a compressor source are routed to a flare, paragraphs (p)(1) through (11) of this section do not apply and instead you must calculate CH4, CO2, and N2O emissions as specified in paragraph (n) of this section and report emissions from the flare as specified in § 98.236(n). If emissions from a compressor source are routed to combustion, paragraphs (p)(1) through (11) of this section do not apply and instead you must calculate and report emissions as specified in subpart C of this part or paragraph (z) of this section, as applicable. If emissions from a compressor source are routed to a vapor recovery system, paragraphs (p)(1) through (11) of this section do not apply.

(1) You must conduct volumetric emission measurements on each reciprocating compressor as specified in this paragraph. Compressor sources (as defined in § 98.238) without manifolded vents must use a measurement method specified in paragraph (p)(1)(i) or (ii) of this section. Manifolded compressor sources (as defined in § 98.238) must use a measurement method specified in paragraph (p)(1)(i), (ii), (iii), or (iv) of this section.

(i) Measure venting from each compressor according to either paragraph (p)(1)(i)(A), (B), or (C) of this section at least once annually, based on the compressor mode (as defined in § 98.238) in which the compressor was found at the time of measurement, except as specified in paragraph (p)(1)(i)(D) of this section. If additional measurements beyond the required annual testing are performed (including duplicate measurements or measurement of additional operating modes), then all measurements satisfying the applicable monitoring and QA/QC that is required by this paragraph (p) must be used in the calculations specified in this section.

(A) For a compressor measured in operating-mode, you must measure volumetric emissions from blowdown valve leakage through the blowdown vent as specified in paragraph (p)(2)(i) of this section, and measure volumetric emissions from reciprocating rod packing as specified in paragraph (p)(2)(ii) or (iii) of this section, as applicable.

(B) For a compressor measured in not-operating-depressurized-mode, you must measure volumetric emissions from isolation valve leakage as specified in paragraph (p)(2)(i) of this section. If a compressor is not operated and has blind flanges in place throughout the reporting period, measurement is not required in this compressor mode.

(C) For a compressor measured in standby-pressurized-mode, you must measure volumetric emissions from blowdown valve leakage through the blowdown vent as specified in paragraph (p)(2)(i) of this section and measure volumetric emissions from reciprocating rod packing as specified in paragraph (p)(2)(ii) or (iii) of this section, as applicable.

(D) An annual as found measurement is not required in the first year of operation for any new compressor that begins operation after as found measurements have been conducted for all existing compressors. For only the first year of operation of new compressors, calculate emissions according to paragraph (p)(6)(ii) of this section.

(ii) Instead of measuring the compressor source according to paragraph (p)(1)(i) of this section for a given compressor, you may elect to continuously measure volumetric emissions from a compressor source as specified in paragraph (p)(3) of this section.

(iii) For a compressor source that is part of a manifolded group of compressor sources (as defined in § 98.238), instead of measuring the compressor source according to paragraph (p)(1)(i), (ii), or (iv) of this section, you may elect to measure combined volumetric emissions from the manifolded group of compressor sources by conducting measurements at the common vent stack as specified in paragraph (p)(4) of this section. The measurements must be conducted at the frequency specified in paragraphs (p)(1)(iii)(A) and (B) of this section.

(A) A minimum of one measurement must be taken for each manifolded group of compressor sources in a calendar year.

(B) The measurement may be performed while the compressors are in any compressor mode.

(iv) For a compressor source that is part of a manifolded group of compressor sources, instead of measuring the compressor source according to paragraph (p)(1)(i), (ii), or (iii) of this section, you may elect to continuously measure combined volumetric emissions from the manifolded group of compressors sources as specified in paragraph (p)(5) of this section.

(2) . If conducting measurements for each compressor source, you must determine the volumetric emissions from blowdown valves and isolation valves as specified in paragraph (p)(2)(i) of this section. You must determine the volumetric emissions from reciprocating rod packing as specified in paragraph (p)(2)(ii) or (iii) of this section, as applicable.

(i) and for isolation valves on compressors in not-operating-depressurized-mode, determine the volumetric emissions using one of the methods specified in paragraphs (p)(2)(i)(A) through (D) of this section.

(A) Determine the volumetric flow at standard conditions from the blowdown vent using calibrated bagging or high volume sampler according to methods set forth in § 98.234(c) and (d), respectively.

(B) Determine the volumetric flow at standard conditions from the blowdown vent using a temporary meter such as a vane anemometer, according to methods set forth in § 98.234(b).

(C) Use an acoustic leak detection device according to methods set forth in § 98.234(a)(5).

(D) You may choose to use any of the methods set forth in § 98.234(a) to screen for emissions. If emissions are detected using the methods set forth in § 98.234(a), then you must use one of the methods specified in paragraphs (p)(2)(i)(A) through (C) of this section. If emissions are not detected using the methods in § 98.234(a), then you may assume that the volumetric emissions are zero. For the purposes of this paragraph, when using any of the methods in § 98.234(a), emissions are detected whenever a leak is detected according to the method.

(ii) For reciprocating rod packing equipped with an open-ended vent line on compressors in operating-mode or standby-pressurized-mode, determine the volumetric emissions using one of the methods specified in paragraphs (p)(2)(ii)(A) through (C) of this section.

(A) Determine the volumetric flow at standard conditions from the open-ended vent line using calibrated bagging or high volume sampler according to methods set forth in § 98.234(c) and (d), respectively.

(B) Determine the volumetric flow at standard conditions from the open-ended vent line using a temporary meter such as a vane anemometer, according to methods set forth in § 98.234(b).

(C) You may choose to use any of the methods set forth in § 98.234(a)(1) through (3) to screen for emissions. If emissions are detected using one of these specified methods, then you must use one of the methods specified in paragraphs (p)(2)(ii)(A) and (B) of this section. If emissions are not detected using the methods in § 98.234(a)(1) through (3), then you may assume that the volumetric emissions are zero. For the purposes of this paragraph (p)(2)(ii)(C), when using any of the methods in § 98.234(a), emissions are detected whenever a leak is detected according to the method. Acoustic leak detection is only applicable for through-valve leakage and is not applicable for screening or measuring rod packing emissions.

(iii) For reciprocating rod packing not equipped with an open-ended vent line on compressors in operating-mode, you must determine the volumetric emissions using the method specified in paragraphs (p)(2)(iii)(A) and (B) of this section.

(A) You must use the methods described in § 98.234(a)(1) through (3) to conduct annual leak detection of equipment leaks from the packing case into an open distance piece, or for compressors with a closed distance piece, conduct annual detection of gas emissions from the rod packing vent, distance piece vent, compressor crank case breather cap, or other vent emitting gas from the rod packing. Acoustic leak detection is only applicable for through-valve leakage and is not applicable for screening rod packing emissions.

(B) You must measure emissions found in paragraph (p)(2)(iii)(A) of this section using an appropriate meter, calibrated bag, or high volume sampler according to methods set forth in § 98.234(b), (c), and (d), respectively.

(3) . If you elect to conduct continuous volumetric emission measurements for an individual compressor source as specified in paragraph (p)(1)(ii) of this section, you must measure volumetric emissions as specified in paragraphs (p)(3)(i) and (p)(3)(ii) of this section.

(i) Continuously measure the volumetric flow for the individual compressor sources at standard conditions using a permanent meter according to methods set forth in § 98.234(b).

(ii) If compressor blowdown emissions are included in the metered emissions specified in paragraph (p)(3)(i) of this section, the compressor blowdown emissions may be included with the reported emissions for the compressor source and do not need to be calculated separately using the method specified in paragraph (i) of this section for blowdown vent stacks.

(4) . If conducting measurements for a manifolded group of compressor sources, you must measure volumetric emissions as specified in paragraphs (p)(4)(i) and (ii) of this section.

(i) Measure at a single point in the manifold downstream of all compressor inputs and, if practical, prior to comingling with other non-compressor emission sources.

(ii) Determine the volumetric flow at standard conditions from the common stack using one of the methods specified in paragraphs (p)(4)(ii)(A) through (F) of this section.

(A) A temporary meter such as a vane anemometer according to methods set forth in § 98.234(b).

(B) Calibrated bagging according to methods set forth in § 98.234(c).

(C) A high volume sampler according to methods set forth in § 98.234(d).

(D) [Reserved]

(E) You may choose to use any of the methods set forth in § 98.234(a)(1) through (3) to screen for emissions. If emissions are detected using one of these specified methods, then you must use one of the methods specified in paragraphs (p)(4)(ii)(A) through (D) of this section. If emissions are not detected using the methods in § 98.234(a)(1) through (3), then you may assume that the volumetric emissions are zero. For the purposes of this paragraph, when using any of the methods in § 98.234(a), emissions are detected whenever a leak is detected according to the method. Acoustic leak detection is only applicable for through-valve leakage and is not applicable for screening a manifolded group of compressor sources.

(F) If one of the screening methods specified in § 98.234(a)(1) through (3) identifies a leak in a manifolded group of reciprocating compressor sources, you may use acoustic leak detection, according to § 98.234(a)(5), to identify the source of the leak. You must use one of the methods specified in paragraphs (p)(4)(ii)(A) through (D) of this section to quantify the emissions from the identified source.

(5) . If you elect to conduct continuous volumetric emission measurements for a manifolded group of compressor sources as specified in paragraph (p)(1)(iv) of this section, you must measure volumetric emissions as specified in paragraphs (p)(5)(i) through (iii) of this section.

(i) Measure at a single point in the manifold downstream of all compressor inputs and, if practical, prior to comingling with other non-compressor emission sources.

(ii) Continuously measure the volumetric flow for the manifolded group of compressor sources at standard conditions using a permanent meter according to methods set forth in § 98.234(b).

(iii) If compressor blowdown emissions are included in the metered emissions specified in paragraph (p)(5)(ii) of this section, the compressor blowdown emissions may be included with the reported emissions for the manifolded group of compressor sources and do not need to be calculated separately using the method specified in paragraph (i) of this section for blowdown vent stacks.

(6) . For compressor sources measured according to paragraph (p)(1)(i) of this section, you must calculate GHG emissions from the compressor sources as specified in paragraphs (p)(6)(i) through (iv) of this section.

(i) Using equation W-26 to this section, calculate the annual volumetric GHG emissions for each reciprocating compressor mode-source combination specified in paragraphs (p)(1)(i)(A) through (C) of this section that was measured during the reporting year.

(ii) Using equation W-27 to this section, calculate the annual volumetric GHG emissions from each reciprocating compressor mode-source combination specified in paragraphs (p)(1)(i)(A) through (C) of this section that was not measured during the reporting year.

(iii) Using equation W-28 to this section, develop an emission factor for each compressor mode-source combination specified in paragraphs (p)(1)(i)(A) through (C) of this section. These emission factors must be calculated annually and used in equation W-27 to this section to determine volumetric emissions from a reciprocating compressor in the mode-source combinations that were not measured in the reporting year.

(iv) The reporter emission factor in equation W-28 to this section may be calculated by using all measurements from a single owner or operator instead of only using measurements from a single facility. If you elect to use this option, the reporter emission factor must be applied to all reporting facilities for the owner or operator.

(7) . For compressor sources measured according to paragraph (p)(1)(ii) of this section, you must use the continuous volumetric emission measurements taken as specified in paragraph (p)(3) of this section and calculate annual volumetric GHG emissions associated with the compressor source using equation W-29A to this section.

(8) For manifolded groups of compressor sources measured according to paragraph (p)(1)(iii) of this section, you must calculate annual GHG emissions using equation W-29B to this section. If the reciprocating compressors included in the manifolded group of compressor sources share the manifold with centrifugal compressors, you must follow the procedures in either this paragraph (p)(8) or paragraph (o)(8) of this section to calculate emissions from the manifolded group of compressor sources.

(9) . For a manifolded group of compressor sources measured according to paragraph (p)(1)(iv) of this section, you must use the continuous volumetric emission measurements taken as specified in paragraph (p)(5) of this section and calculate annual volumetric GHG emissions associated with each manifolded group of compressor sources using equation W-29C to this section. If the reciprocating compressors included in the manifolded group of compressor sources share the manifold with centrifugal compressors, you must follow the procedures in either this paragraph (p)(9) or paragraph (o)(9) of this section to calculate emissions from the manifolded group of compressor sources.

(10) . You must calculate volumetric emissions from reciprocating compressors at an onshore petroleum and natural gas production facility or an onshore petroleum and natural gas gathering and boosting facility as specified in paragraphs (p)(10)(i) through (iv) of this section, as applicable.

(i) For all reciprocating compressors at an onshore petroleum and natural gas production facility or an onshore petroleum and natural gas gathering and boosting facility that are subject to the reciprocating compressor standards in § 60.5385b of this chapter or an applicable approved state plan or applicable Federal plan in part 62 of this chapter, you must conduct the volumetric emission measurements as required by § 60.5385b(b) and (c) of this chapter or an applicable approved state plan or applicable Federal plan in part 62 of this chapter, conduct any additional volumetric emission measurements specified in paragraph (p)(1) of this section using methods specified in paragraphs (p)(2) through (5) of this section (based on the compressor mode (as defined in § 98.238) in which the compressor was found at the time of measurement), and calculate emissions as specified in paragraphs (p)(6) through (9) of this section. Conduct all measurements required by this paragraph (p)(10)(i) at the frequency specified by § 60.5385b(a) of this chapter or an applicable approved state plan or applicable Federal plan in part 62 of this chapter. For any reporting year in which measuring at the frequency specified by § 60.5385b(a) of this chapter results in measurement not being required for a subject compressor, calculate emissions for all mode-source combinations as specified in paragraph (p)(6)(ii) of this section.

(ii) For all reciprocating compressors at an onshore petroleum and natural gas production facility or an onshore petroleum and natural gas gathering and boosting facility that are not subject to the reciprocating compressor standards in § 60.5385b of this chapter or an applicable approved state plan or applicable Federal plan in part 62 of this chapter, you may elect to conduct volumetric emission measurements specified in paragraph (p)(1) of this section using methods specified in paragraphs (p)(2) through (5) of this section (based on the compressor mode (as defined in § 98.238) in which the compressor was found at the time of measurement), and calculate emissions as specified in paragraphs (p)(6) through (9) of this section.

(iii) For all reciprocating compressors at an onshore petroleum and natural gas production facility or an onshore petroleum and natural gas gathering and boosting facility for which paragraph (p)(10)(i) of this section does not apply, and you do not elect to conduct volumetric emission measurements specified in paragraph (p)(1) of this section, you must calculate total atmospheric rod packing emissions from all reciprocating compressors at either an onshore petroleum and natural gas production facility or an onshore petroleum and natural gas gathering and boosting facility using equation W-29D to this section. Reciprocating compressor rod packing emissions that are routed to a flare, combustion, or vapor recovery system are not required to be determined under this paragraph (p).

(iv) For all reciprocating compressors at an onshore petroleum and natural gas production facility or an onshore petroleum and natural gas gathering and boosting facility for which paragraph (p)(10)(i) of this section does not apply, you must calculate rod packing vent emissions from each reciprocating compressor using equation W-29E to this section. Reciprocating compressor rod packing emissions that are routed to a flare, combustion, or vapor recovery system are not required to be determined under this paragraph (p).

(11) You must calculate both CH4 and CO2 mass emissions from volumetric emissions using calculations in paragraph (v) of this section.

(o) If you are required to report emissions from centrifugal compressor venting as specified in § 98.232(d)(2), (e)(2), (f)(2), (g)(2), and (h)(2), you must conduct volumetric emission measurements specified in paragraph (o)(1) of this section using methods specified in paragraphs (o)(2) through (5) of this section; perform calculations specified in paragraphs (o)(6) through (9) of this section; and calculate CH4 and CO2 mass emissions as specified in paragraph (o)(11) of this section. If you are required to report emissions from centrifugal compressor venting at an onshore petroleum and natural gas production facility as specified in § 98.232(c)(19) or an onshore petroleum and natural gas gathering and boosting facility as specified in § 98.232(j)(8), you must calculate volumetric emissions as specified in paragraph (o)(10) of this section and calculate CH4 and CO2 mass emissions as specified in paragraph (o)(11) of this section. If emissions from a compressor source are routed to a flare, paragraphs (o)(1) through (11) of this section do not apply and instead you must calculate CH4, CO2, and N2O emissions as specified in paragraph (n) of this section and report emissions from the flare as specified in § 98.236(n). If emissions from a compressor source are routed to combustion, paragraphs (o)(1) through (11) of this section do not apply and instead you must calculate and report emissions as specified in subpart C of this part or paragraph (z) of this section, as applicable. If emissions from a compressor source are routed to a vapor recovery system, paragraphs (o)(1) through (11) of this section do not apply.

(1) You must conduct volumetric emission measurements on each centrifugal compressor as specified in this paragraph. Compressor sources (as defined in § 98.238) without manifolded vents must use a measurement method specified in paragraph (o)(1)(i) or (ii) of this section. Manifolded compressor sources (as defined in § 98.238) must use a measurement method specified in paragraph (o)(1)(i), (ii), (iii), or (iv) of this section.

(i) Measure venting from each compressor according to either paragraph (o)(1)(i)(A), (B), or (C) of this section at least once annually, based on the compressor mode (as defined in § 98.238) in which the compressor was found at the time of measurement, except as specified in paragraph (o)(1)(i)(D) of this section. If additional measurements beyond the required annual testing are performed (including duplicate measurements or measurement of additional operating modes), then all measurements satisfying the applicable monitoring and QA/QC that is required by this paragraph (o) must be used in the calculations specified in this section.

(A) For a compressor measured in operating-mode, you must measure volumetric emissions from blowdown valve leakage through the blowdown vent as specified in paragraph (o)(2)(i) of this section, measure volumetric emissions from wet seal oil degassing vents as specified in paragraph (o)(2)(ii) of this section if the compressor has wet seal oil degassing vents, and measure volumetric emissions from dry seal vents as specified in paragraph (o)(2)(iii) of this section if the compressor has dry seals.

(B) For a compressor measured in not-operating-depressurized-mode, you must measure volumetric emissions from isolation valve leakage as specified in paragraph (o)(2)(i) of this section. If a compressor is not operated and has blind flanges in place throughout the reporting period, measurement is not required in this compressor mode.

(C) For a compressor measured in standby-pressurized-mode, you must measure volumetric emissions from blowdown valve leakage through the blowdown vent as specified in paragraph (o)(2)(i) of this section, measure volumetric emissions from wet seal oil degassing vents as specified in paragraph (o)(2)(ii) of this section if the compressor has wet seal oil degassing vents, and measure volumetric emissions from dry seal vents as specified in paragraph (o)(2)(iii) of this section if the compressor has dry seals.

(D) An annual as found measurement is not required in the first year of operation for any new compressor that begins operation after as found measurements have been conducted for all existing compressors. For only the first year of operation of new compressors, calculate emissions according to paragraph (o)(6)(ii) of this section.

(ii) Instead of measuring the compressor source according to paragraph (o)(1)(i) of this section for a given compressor, you may elect to continuously measure volumetric emissions from a compressor source as specified in paragraph (o)(3) of this section.

(iii) For a compressor source that is part of a manifolded group of compressor sources (as defined in § 98.238), instead of measuring the compressor source according to paragraph (o)(1)(i), (ii), or (iv) of this section, you may elect to measure combined volumetric emissions from the manifolded group of compressor sources by conducting measurements at the common vent stack as specified in paragraph (o)(4) of this section. The measurements must be conducted at the frequency specified in paragraphs (o)(1)(iii)(A) and (B) of this section.

(A) A minimum of one measurement must be taken for each manifolded group of compressor sources in a calendar year.

(B) The measurement may be performed while the compressors are in any compressor mode.

(iv) For a compressor source that is part of a manifolded group of compressor sources, instead of measuring the compressor source according to paragraph (o)(1)(i), (ii), or (iii) of this section, you may elect to continuously measure combined volumetric emissions from the manifolded group of compressor sources as specified in paragraph (o)(5) of this section.

(2) . If conducting measurements for each compressor source, you must determine the volumetric emissions from blowdown valves and isolation valves as specified in paragraph (o)(2)(i) of this section, the volumetric emissions from wet seal oil degassing vents as specified in paragraph (o)(2)(ii) of this section, and the volumetric emissions from dry seal vents as specified in paragraph (o)(2)(iii) of this section.

(i) For blowdown valves on compressors in operating-mode or in standby-pressurized-mode and for isolation valves on compressors in not-operating-depressurized-mode, determine the volumetric emissions using one of the methods specified in paragraphs (o)(2)(i)(A) through (D) of this section.

(A) Determine the volumetric flow at standard conditions from the blowdown vent using calibrated bagging or high volume sampler according to methods set forth in § 98.234(c) and § 98.234(d), respectively.

(B) Determine the volumetric flow at standard conditions from the blowdown vent using a temporary meter such as a vane anemometer according to methods set forth in § 98.234(b).

(C) Use an acoustic leak detection device according to methods set forth in § 98.234(a)(5).

(D) You may choose to use any of the methods set forth in § 98.234(a) to screen for emissions. If emissions are detected using the methods set forth in § 98.234(a), then you must use one of the methods specified in paragraph (o)(2)(i)(A) through (C) of this section. If emissions are not detected using the methods in § 98.234(a), then you may assume that the volumetric emissions are zero. For the purposes of this paragraph, when using any of the methods in § 98.234(a), emissions are detected whenever a leak is detected according to the methods.

(ii) For wet seal oil degassing vents in operating-mode or in standby-pressurized-mode, determine volumetric flow at standard conditions, using one of the methods specified in paragraphs (o)(2)(ii)(A) through (C) of this section. You must quantitatively measure the volumetric flow for wet seal oil degassing vent; you may not use screening methods set forth in § 98.234(a) to screen for emissions for the wet seal oil degassing vent.

(A) Use a temporary meter such as a vane anemometer or permanent flow meter according to methods set forth in § 98.234(b).

(B) Use calibrated bags according to methods set forth in § 98.234(c).

(C) Use a high volume sampler according to methods set forth in § 98.234(d).

(iii) For dry seal vents in operating-mode or in standby-pressurized-mode, determine volumetric flow at standard conditions from each dry seal vent using one of the methods specified in paragraphs (o)(2)(iii)(A) through (D) of this section. The measurement should be conducted on the compressor side dry seal. If a compressor has more than one dry seal vent, determine the aggregate dry seal vent volumetric flow for the compressor as the sum of the volumetric flows determined for each dry seal vent on the compressor.

(A) Use a temporary meter such as a vane anemometer or permanent flow meter according to methods set forth in § 98.234(b).

(B) Use calibrated bags according to methods set forth in § 98.234(c).

(C) Use a high volume sampler according to methods set forth in § 98.234(d).

(D) You may choose to use any of the methods set forth in § 98.234(a)(1) through (3) to screen for emissions. If emissions are detected using one of these specified methods, then you must use one of the methods specified in paragraph (o)(2)(iii)(A) through (C) of this section. If emissions are not detected using the methods in § 98.234(a)(1) through (3), then you may assume that the volumetric emissions are zero. For the purposes of this paragraph, when using any of the methods in § 98.234(a), emissions are detected whenever a leak is detected according to the methods. Acoustic leak detection is only applicable for through-valve leakage and is not applicable for screening dry seal vents.

(3) If you elect to conduct continuous volumetric emission measurements for an individual compressor source as specified in paragraph (o)(1)(ii) of this section, you must measure volumetric emissions as specified in paragraphs (o)(3)(i) and (ii) of this section.

(i) Continuously measure the volumetric flow for the individual compressor source at standard conditions using a permanent meter according to methods set forth in § 98.234(b).

(ii) If compressor blowdown emissions are included in the metered emissions specified in paragraph (o)(3)(i) of this section, the compressor blowdown emissions may be included with the reported emissions for the compressor source and do not need to be calculated separately using the method specified in paragraph (i) of this section for blowdown vent stacks.

(4) If conducting measurements for a manifolded group of compressor sources, you must measure volumetric emissions as specified in paragraphs (o)(4)(i) and (ii) of this section.

(i) Measure at a single point in the manifold downstream of all compressor inputs and, if practical, prior to comingling with other non-compressor emission sources.

(ii) Determine the volumetric flow at standard conditions from the common stack using one of the methods specified in paragraphs (o)(4)(ii)(A) through (F) of this section.

(A) A temporary meter such as a vane anemometer according the methods set forth in § 98.234(b).

(B) Calibrated bagging according to methods set forth in § 98.234(c).

(C) A high volume sampler according to methods set forth § 98.234(d).

(D) [Reserved]

(E) You may choose to use any of the methods set forth in § 98.234(a)(1) through (3) to screen for emissions. If emissions are detected using one of these methods, then you must use one of the methods specified in paragraph (o)(4)(ii)(A) through (D) of this section. If emissions are not detected using the methods in § 98.234(a)(1) through (3), then you may assume that the volumetric emissions are zero. For the purposes of this paragraph, when using any of the methods in § 98.234(a), emissions are detected whenever a leak is detected according to the method. Acoustic leak detection is only applicable for through-valve leakage and is not applicable for screening a manifolded group of compressor sources.

(F) If one of the screening methods specified in § 98.234(a)(1) through (3) identifies a leak in a manifolded group of centrifugal compressor sources, you may use acoustic leak detection, according to § 98.234(a)(5), to identify the source of the leak. You must use one of the methods specified in paragraphs (o)(4)(ii)(A) through (D) of this section to quantify emissions from the identified source.

(5) If you elect to conduct continuous volumetric emission measurements for a manifolded group of compressor sources as specified in paragraph (o)(1)(iv) of this section, you must measure volumetric emissions as specified in paragraphs (o)(5)(i) through (iii) of this section.

(i) Measure at a single point in the manifold downstream of all compressor inputs and, if practical, prior to comingling with other non-compressor emission sources.

(ii) Continuously measure the volumetric flow for the manifolded group of compressor sources at standard conditions using a permanent meter according to methods set forth in § 98.234(b).

(iii) If compressor blowdown emissions are included in the metered emissions specified in paragraph (o)(5)(ii) of this section, the compressor blowdown emissions may be included with the reported emissions for the manifolded group of compressor sources and do not need to be calculated separately using the method specified in paragraph (i) of this section for blowdown vent stacks.

(6) . For compressor sources measured according to paragraph (o)(1)(i) of this section, you must calculate annual GHG emissions from the compressor sources as specified in paragraphs (o)(6)(i) through (iv) of this section.

(i) Using equation W-21 to this section, calculate the annual volumetric GHG emissions for each centrifugal compressor mode-source combination specified in paragraphs (o)(1)(i)(A) through (C) of this section that was measured during the reporting year.

(ii) Using equation W-22 to this section, calculate the annual volumetric GHG emissions from each centrifugal compressor mode-source combination specified in paragraphs (o)(1)(i)(A) through (C) of this section that was not measured during the reporting year.

(iii) Using equation W-23 to this section, develop an emission factor for each compressor mode-source combination specified in paragraphs (o)(1)(i)(A) through (C) of this section. These emission factors must be calculated annually and used in equation W-22 to this section to determine volumetric emissions from a centrifugal compressor in the mode- source combinations that were not measured in the reporting year.

(iv) The reporter emission factor in equation W-23 to this section may be calculated by using all measurements from a single owner or operator instead of only using measurements from a single facility. If you elect to use this option, the reporter emission factor must be applied to all reporting facilities for the owner or operator.

(7) . For compressor sources measured according to paragraph (o)(1)(ii) of this section, you must use the continuous volumetric emission measurements taken as specified in paragraph (o)(3) of this section and calculate annual volumetric GHG emissions associated with the compressor source using equation W-24A to this section.

(8) . For manifolded groups of compressor sources measured according to paragraph (o)(1)(iii) of this section, you must calculate annual volumetric GHG emissions using equation W-24B to this section. If the centrifugal compressors included in the manifolded group of compressor sources share the manifold with reciprocating compressors, you must follow the procedures in either this paragraph (o)(8) or paragraph (p)(8) of this section to calculate emissions from the manifolded group of compressor sources.

(9) For a manifolded group of compressor sources measured according to paragraph (o)(1)(iv) of this section, you must use the continuous volumetric emission measurements taken as specified in paragraph (o)(5) of this section and calculate annual volumetric GHG emissions associated with each manifolded group of compressor sources using equation W-24C to this section. If the centrifugal compressors included in the manifolded group of compressor sources share the manifold with reciprocating compressors, you must follow the procedures in either this paragraph (o)(9) or paragraph (p)(9) of this section to calculate emissions from the manifolded group of compressor sources.

(10) You must calculate volumetric emissions from centrifugal compressors at an onshore petroleum and natural gas production facility or an onshore petroleum and natural gas gathering and boosting facility as specified in paragraphs (o)(10)(i) through (iv), as applicable.

(i) For all centrifugal compressors at an onshore petroleum and natural gas production facility or an onshore petroleum and natural gas gathering and boosting facility that are subject to the centrifugal compressor standards in § 60.5380b of this chapter or an applicable approved state plan or applicable Federal plan in part 62 of this chapter for dry seals and self-contained wet seals, you must conduct the volumetric emission measurements as required by § 60.5380b(a)(5) of this chapter or an applicable approved state plan or applicable Federal plan in part 62 of this chapter, conduct all additional volumetric emission measurements specified in paragraph (o)(1) of this section using methods specified in paragraphs (o)(2) through (5) of this section (based on the compressor mode (as defined in § 98.238) in which the compressor was found at the time of measurement), and calculate emissions as specified in paragraphs (o)(6) through (9) of this section. Conduct all measurements required by this paragraph (o)(10)(i) at the frequency specified by § 60.5380b(a)(4) of this chapter or an applicable approved state plan or applicable Federal plan in part 62 of this chapter. For any reporting year in which measuring at the frequency specified by § 60.5380b(a)(4) of this chapter results in measurement not being required for a subject compressor, calculate emissions for all mode-source combinations as specified in paragraph (o)(6)(ii) of this section.

(ii) For all centrifugal compressors at an onshore petroleum and natural gas production facility or an onshore petroleum and natural gas gathering and boosting facility that are not subject to the centrifugal compressor standards in § 60.5380b of this chapter or an applicable approved state plan or applicable Federal plan in part 62 of this chapter for dry seals and self-contained wet seals, you may elect to conduct the volumetric emission measurements specified in paragraph (o)(1) of this section using methods specified in paragraphs (o)(2) through (5) of this section (based on the compressor mode (as defined in § 98.238) in which the compressor was found at the time of measurement), and calculate emissions as specified in paragraphs (o)(6) through (9) of this section.

(iii) For all centrifugal compressors at an onshore petroleum and natural gas production facility or an onshore petroleum and natural gas gathering and boosting facility for which paragraph (o)(10)(i) of this section does not apply and you do not elect to conduct the volumetric measurements specified in paragraph (o)(1) of this section, you must calculate total atmospheric wet seal oil degassing vent emissions from all centrifugal compressors at either an onshore petroleum and natural gas production facility or an onshore petroleum and natural gas gathering and boosting facility using equation W-25A to this section. Emissions from centrifugal compressor wet seal oil degassing vents that are routed to a flare, combustion, or vapor recovery system are not required to be determined under this paragraph (o).

(iv) For all centrifugal compressors at an onshore petroleum and natural gas production facility or an onshore petroleum and natural gas gathering and boosting facility for which paragraph (o)(10)(i) of this section does not apply, and you do not elect to conduct the volumetric measurements specified in paragraph (o)(1) of this section, you must calculate wet seal oil degassing vent emissions from each centrifugal compressor using equation W-25B to this section. Emissions from centrifugal compressor wet seal oil degassing vents that are routed to a flare, combustion, or vapor recovery system are not required to be determined under this paragraph (o).

(11) . You must calculate both CH4 and CO2 mass emissions from volumetric emissions using calculations in paragraph (v) of this section.

(i) For the components listed in § 98.232(e)(7), (f)(5), (g)(4), and (h)(5), that are not subject to the well site or compressor station fugitive emissions standards in § 60.5397a of this chapter, the fugitive emissions standards for well sites, centralized production facilities, and compressor stations in § 60.5397b or 60.5398b of this chapter, or an applicable approved state plan or applicable Federal plan in part 62 of this chapter, you must conduct surveys using any of the leak detection methods listed in § 98.234(a) and calculate equipment leak emissions using the procedures specified in either paragraph (q)(2) or (3) of this section.

(2) You must indicate whether your facility contains any of the component types subject to or complying with § 98.233(q) that are listed in § 98.232(c)(21), (d)(7), (e)(7) or (8), (f)(5) through (8), (g)(4), (g)(6) or (7), (h)(5), (h)(7) or (8), (i)(1), (j)(10), (m)(3)(ii) or (m)(4)(ii) for your facility's industry segment. For each component type and leak detection method combination that is located at your well-pad site, gathering and boosting site, or facility, you must report the information specified in paragraphs (q)(2)(i) through (ix) of this section. If a component type is located at your well-pad site, gathering and boosting site, or facility and no leaks were identified from that component, then you must report the information in paragraphs (q)(2)(i) through (ix) of this section but report a zero (“0”) for the information required according to paragraphs (q)(2)(vi) through (ix) of this section. If you used Calculation Method 1 (leaker factor emission calculation methodology) for some complete leak surveys and used Calculation Method 2 (leaker measurement methodology) for some complete leak surveys, you must report the information specified in paragraphs (q)(2)(i) through (ix) of this section separately for component surveys using Calculation Method 1 and Calculation Method 2.

(i) Well-pad ID (for the onshore petroleum and natural gas production industry segment only) or gathering and boosting site ID (for the onshore petroleum and natural gas gathering and boosting industry segment only).

(iii) Leak detection method used for the screening survey (e.g., Method 21 as specified in § 98.234(a)(2)(i); Method 21 as specified in § 98.234(a)(2)(ii); and OGI and other leak detection methods as specified in § 98.234(a)(1), (3), or (5)).

(iv) Emission factor or measurement method used (e.g., default emission factor; facility-specific emission factor developed according to § 98.233(q)(4); or direct measurement according to § 98.233(q)(3)).

(vi) Total number of the surveyed component types by leak detection method that were identified as leaking in the calendar year (“xp” in equation W-30 to § 98.233 for the component type or the number of leaks measured for the specified component type according to the provisions in § 98.233(q)(3)).

(vii) Average time the surveyed components are assumed to be leaking and operational, in hours (average of “Tp,z” from equation W-30 to § 98.233 for the component type or average duration of leaks for the specified component type determined according to the provisions in § 98.233(q)(3)(ii)).

(viii) Annual CO2 emissions, in metric tons CO2, for the component type as calculated using equation W-30 to § 98.233 or § 98.233(q)(3)(vii) (for surveyed components only).

(ix) Annual CH4 emissions, in metric tons CH4, for the component type as calculated using equation W-30 to § 98.233 or § 98.233(q)(3)(vii) (for surveyed components only).

(B) If you elect to use a leak detection method in § 98.234(a) for the surveyed component types in § 98.232(e)(8), (f)(6) and (8), (g)(7), and (h)(8), then you must use the procedures in either paragraph (q)(2) or (3) of this section to calculate those emissions.

(2) You must indicate whether your facility contains any of the component types subject to or complying with § 98.233(q) that are listed in § 98.232(c)(21), (d)(7), (e)(7) or (8), (f)(5) through (8), (g)(4), (g)(6) or (7), (h)(5), (h)(7) or (8), (i)(1), (j)(10), (m)(3)(ii) or (m)(4)(ii) for your facility's industry segment. For each component type and leak detection method combination that is located at your well-pad site, gathering and boosting site, or facility, you must report the information specified in paragraphs (q)(2)(i) through (ix) of this section. If a component type is located at your well-pad site, gathering and boosting site, or facility and no leaks were identified from that component, then you must report the information in paragraphs (q)(2)(i) through (ix) of this section but report a zero (“0”) for the information required according to paragraphs (q)(2)(vi) through (ix) of this section. If you used Calculation Method 1 (leaker factor emission calculation methodology) for some complete leak surveys and used Calculation Method 2 (leaker measurement methodology) for some complete leak surveys, you must report the information specified in paragraphs (q)(2)(i) through (ix) of this section separately for component surveys using Calculation Method 1 and Calculation Method 2.

(i) Well-pad ID (for the onshore petroleum and natural gas production industry segment only) or gathering and boosting site ID (for the onshore petroleum and natural gas gathering and boosting industry segment only).

(iii) Leak detection method used for the screening survey (e.g., Method 21 as specified in § 98.234(a)(2)(i); Method 21 as specified in § 98.234(a)(2)(ii); and OGI and other leak detection methods as specified in § 98.234(a)(1), (3), or (5)).

(iv) Emission factor or measurement method used (e.g., default emission factor; facility-specific emission factor developed according to § 98.233(q)(4); or direct measurement according to § 98.233(q)(3)).

(vi) Total number of the surveyed component types by leak detection method that were identified as leaking in the calendar year (“xp” in equation W-30 to § 98.233 for the component type or the number of leaks measured for the specified component type according to the provisions in § 98.233(q)(3)).

(vii) Average time the surveyed components are assumed to be leaking and operational, in hours (average of “Tp,z” from equation W-30 to § 98.233 for the component type or average duration of leaks for the specified component type determined according to the provisions in § 98.233(q)(3)(ii)).

(viii) Annual CO2 emissions, in metric tons CO2, for the component type as calculated using equation W-30 to § 98.233 or § 98.233(q)(3)(vii) (for surveyed components only).

(ix) Annual CH4 emissions, in metric tons CH4, for the component type as calculated using equation W-30 to § 98.233 or § 98.233(q)(3)(vii) (for surveyed components only).

(a) You must report CO2, CH4, and N2O emissions from each industry segment specified in paragraphs (b) through (j) and (m) of this section, CO2, CH4, and N2O emissions from each flare as specified in paragraphs (b) through (j) of this section, and stationary and portable combustion emissions as applicable as specified in paragraph (k) of this section. You must also report the information specified in paragraph (l) of this section, as applicable.

(p) If you are required to report emissions from reciprocating compressor venting as specified in § 98.232(d)(1), (e)(1), (f)(1), (g)(1), and (h)(1), you must conduct volumetric emission measurements specified in paragraph (p)(1) of this section using methods specified in paragraphs (p)(2) through (5) of this section; perform calculations specified in paragraphs (p)(6) through (9) of this section; and calculate CH4 and CO2 mass emissions as specified in paragraph (p)(11) of this section. If you are required to report emissions from reciprocating compressor venting at an onshore petroleum and natural gas production facility as specified in § 98.232(c)(11) or an onshore petroleum and natural gas gathering and boosting facility as specified in § 98.232(j)(9), you must calculate volumetric emissions as specified in paragraph (p)(10) of this section and calculate CH4 and CO2 mass emissions as specified in paragraph (p)(11) of this section. If emissions from a compressor source are routed to a flare, paragraphs (p)(1) through (11) of this section do not apply and instead you must calculate CH4, CO2, and N2O emissions as specified in paragraph (n) of this section and report emissions from the flare as specified in § 98.236(n). If emissions from a compressor source are routed to combustion, paragraphs (p)(1) through (11) of this section do not apply and instead you must calculate and report emissions as specified in subpart C of this part or paragraph (z) of this section, as applicable. If emissions from a compressor source are routed to a vapor recovery system, paragraphs (p)(1) through (11) of this section do not apply.

(1) You must conduct volumetric emission measurements on each reciprocating compressor as specified in this paragraph. Compressor sources (as defined in § 98.238) without manifolded vents must use a measurement method specified in paragraph (p)(1)(i) or (ii) of this section. Manifolded compressor sources (as defined in § 98.238) must use a measurement method specified in paragraph (p)(1)(i), (ii), (iii), or (iv) of this section.

(i) Measure venting from each compressor according to either paragraph (p)(1)(i)(A), (B), or (C) of this section at least once annually, based on the compressor mode (as defined in § 98.238) in which the compressor was found at the time of measurement, except as specified in paragraph (p)(1)(i)(D) of this section. If additional measurements beyond the required annual testing are performed (including duplicate measurements or measurement of additional operating modes), then all measurements satisfying the applicable monitoring and QA/QC that is required by this paragraph (p) must be used in the calculations specified in this section.

(A) For a compressor measured in operating-mode, you must measure volumetric emissions from blowdown valve leakage through the blowdown vent as specified in paragraph (p)(2)(i) of this section, and measure volumetric emissions from reciprocating rod packing as specified in paragraph (p)(2)(ii) or (iii) of this section, as applicable.

(B) For a compressor measured in not-operating-depressurized-mode, you must measure volumetric emissions from isolation valve leakage as specified in paragraph (p)(2)(i) of this section. If a compressor is not operated and has blind flanges in place throughout the reporting period, measurement is not required in this compressor mode.

(C) For a compressor measured in standby-pressurized-mode, you must measure volumetric emissions from blowdown valve leakage through the blowdown vent as specified in paragraph (p)(2)(i) of this section and measure volumetric emissions from reciprocating rod packing as specified in paragraph (p)(2)(ii) or (iii) of this section, as applicable.

(D) An annual as found measurement is not required in the first year of operation for any new compressor that begins operation after as found measurements have been conducted for all existing compressors. For only the first year of operation of new compressors, calculate emissions according to paragraph (p)(6)(ii) of this section.

(ii) Instead of measuring the compressor source according to paragraph (p)(1)(i) of this section for a given compressor, you may elect to continuously measure volumetric emissions from a compressor source as specified in paragraph (p)(3) of this section.

(iii) For a compressor source that is part of a manifolded group of compressor sources (as defined in § 98.238), instead of measuring the compressor source according to paragraph (p)(1)(i), (ii), or (iv) of this section, you may elect to measure combined volumetric emissions from the manifolded group of compressor sources by conducting measurements at the common vent stack as specified in paragraph (p)(4) of this section. The measurements must be conducted at the frequency specified in paragraphs (p)(1)(iii)(A) and (B) of this section.

(A) A minimum of one measurement must be taken for each manifolded group of compressor sources in a calendar year.

(B) The measurement may be performed while the compressors are in any compressor mode.

(iv) For a compressor source that is part of a manifolded group of compressor sources, instead of measuring the compressor source according to paragraph (p)(1)(i), (ii), or (iii) of this section, you may elect to continuously measure combined volumetric emissions from the manifolded group of compressors sources as specified in paragraph (p)(5) of this section.

(2) . If conducting measurements for each compressor source, you must determine the volumetric emissions from blowdown valves and isolation valves as specified in paragraph (p)(2)(i) of this section. You must determine the volumetric emissions from reciprocating rod packing as specified in paragraph (p)(2)(ii) or (iii) of this section, as applicable.

(i) and for isolation valves on compressors in not-operating-depressurized-mode, determine the volumetric emissions using one of the methods specified in paragraphs (p)(2)(i)(A) through (D) of this section.

(A) Determine the volumetric flow at standard conditions from the blowdown vent using calibrated bagging or high volume sampler according to methods set forth in § 98.234(c) and (d), respectively.

(B) Determine the volumetric flow at standard conditions from the blowdown vent using a temporary meter such as a vane anemometer, according to methods set forth in § 98.234(b).

(C) Use an acoustic leak detection device according to methods set forth in § 98.234(a)(5).

(D) You may choose to use any of the methods set forth in § 98.234(a) to screen for emissions. If emissions are detected using the methods set forth in § 98.234(a), then you must use one of the methods specified in paragraphs (p)(2)(i)(A) through (C) of this section. If emissions are not detected using the methods in § 98.234(a), then you may assume that the volumetric emissions are zero. For the purposes of this paragraph, when using any of the methods in § 98.234(a), emissions are detected whenever a leak is detected according to the method.

(ii) For reciprocating rod packing equipped with an open-ended vent line on compressors in operating-mode or standby-pressurized-mode, determine the volumetric emissions using one of the methods specified in paragraphs (p)(2)(ii)(A) through (C) of this section.

(A) Determine the volumetric flow at standard conditions from the open-ended vent line using calibrated bagging or high volume sampler according to methods set forth in § 98.234(c) and (d), respectively.

(B) Determine the volumetric flow at standard conditions from the open-ended vent line using a temporary meter such as a vane anemometer, according to methods set forth in § 98.234(b).

(C) You may choose to use any of the methods set forth in § 98.234(a)(1) through (3) to screen for emissions. If emissions are detected using one of these specified methods, then you must use one of the methods specified in paragraphs (p)(2)(ii)(A) and (B) of this section. If emissions are not detected using the methods in § 98.234(a)(1) through (3), then you may assume that the volumetric emissions are zero. For the purposes of this paragraph (p)(2)(ii)(C), when using any of the methods in § 98.234(a), emissions are detected whenever a leak is detected according to the method. Acoustic leak detection is only applicable for through-valve leakage and is not applicable for screening or measuring rod packing emissions.

(iii) For reciprocating rod packing not equipped with an open-ended vent line on compressors in operating-mode, you must determine the volumetric emissions using the method specified in paragraphs (p)(2)(iii)(A) and (B) of this section.

(A) You must use the methods described in § 98.234(a)(1) through (3) to conduct annual leak detection of equipment leaks from the packing case into an open distance piece, or for compressors with a closed distance piece, conduct annual detection of gas emissions from the rod packing vent, distance piece vent, compressor crank case breather cap, or other vent emitting gas from the rod packing. Acoustic leak detection is only applicable for through-valve leakage and is not applicable for screening rod packing emissions.

(B) You must measure emissions found in paragraph (p)(2)(iii)(A) of this section using an appropriate meter, calibrated bag, or high volume sampler according to methods set forth in § 98.234(b), (c), and (d), respectively.

(3) . If you elect to conduct continuous volumetric emission measurements for an individual compressor source as specified in paragraph (p)(1)(ii) of this section, you must measure volumetric emissions as specified in paragraphs (p)(3)(i) and (p)(3)(ii) of this section.

(i) Continuously measure the volumetric flow for the individual compressor sources at standard conditions using a permanent meter according to methods set forth in § 98.234(b).

(ii) If compressor blowdown emissions are included in the metered emissions specified in paragraph (p)(3)(i) of this section, the compressor blowdown emissions may be included with the reported emissions for the compressor source and do not need to be calculated separately using the method specified in paragraph (i) of this section for blowdown vent stacks.

(4) . If conducting measurements for a manifolded group of compressor sources, you must measure volumetric emissions as specified in paragraphs (p)(4)(i) and (ii) of this section.

(i) Measure at a single point in the manifold downstream of all compressor inputs and, if practical, prior to comingling with other non-compressor emission sources.

(ii) Determine the volumetric flow at standard conditions from the common stack using one of the methods specified in paragraphs (p)(4)(ii)(A) through (F) of this section.

(A) A temporary meter such as a vane anemometer according to methods set forth in § 98.234(b).

(B) Calibrated bagging according to methods set forth in § 98.234(c).

(C) A high volume sampler according to methods set forth in § 98.234(d).

(D) [Reserved]

(E) You may choose to use any of the methods set forth in § 98.234(a)(1) through (3) to screen for emissions. If emissions are detected using one of these specified methods, then you must use one of the methods specified in paragraphs (p)(4)(ii)(A) through (D) of this section. If emissions are not detected using the methods in § 98.234(a)(1) through (3), then you may assume that the volumetric emissions are zero. For the purposes of this paragraph, when using any of the methods in § 98.234(a), emissions are detected whenever a leak is detected according to the method. Acoustic leak detection is only applicable for through-valve leakage and is not applicable for screening a manifolded group of compressor sources.

(F) If one of the screening methods specified in § 98.234(a)(1) through (3) identifies a leak in a manifolded group of reciprocating compressor sources, you may use acoustic leak detection, according to § 98.234(a)(5), to identify the source of the leak. You must use one of the methods specified in paragraphs (p)(4)(ii)(A) through (D) of this section to quantify the emissions from the identified source.

(5) . If you elect to conduct continuous volumetric emission measurements for a manifolded group of compressor sources as specified in paragraph (p)(1)(iv) of this section, you must measure volumetric emissions as specified in paragraphs (p)(5)(i) through (iii) of this section.

(i) Measure at a single point in the manifold downstream of all compressor inputs and, if practical, prior to comingling with other non-compressor emission sources.

(ii) Continuously measure the volumetric flow for the manifolded group of compressor sources at standard conditions using a permanent meter according to methods set forth in § 98.234(b).

(iii) If compressor blowdown emissions are included in the metered emissions specified in paragraph (p)(5)(ii) of this section, the compressor blowdown emissions may be included with the reported emissions for the manifolded group of compressor sources and do not need to be calculated separately using the method specified in paragraph (i) of this section for blowdown vent stacks.

(6) . For compressor sources measured according to paragraph (p)(1)(i) of this section, you must calculate GHG emissions from the compressor sources as specified in paragraphs (p)(6)(i) through (iv) of this section.

(i) Using equation W-26 to this section, calculate the annual volumetric GHG emissions for each reciprocating compressor mode-source combination specified in paragraphs (p)(1)(i)(A) through (C) of this section that was measured during the reporting year.

(ii) Using equation W-27 to this section, calculate the annual volumetric GHG emissions from each reciprocating compressor mode-source combination specified in paragraphs (p)(1)(i)(A) through (C) of this section that was not measured during the reporting year.

(iii) Using equation W-28 to this section, develop an emission factor for each compressor mode-source combination specified in paragraphs (p)(1)(i)(A) through (C) of this section. These emission factors must be calculated annually and used in equation W-27 to this section to determine volumetric emissions from a reciprocating compressor in the mode-source combinations that were not measured in the reporting year.

(iv) The reporter emission factor in equation W-28 to this section may be calculated by using all measurements from a single owner or operator instead of only using measurements from a single facility. If you elect to use this option, the reporter emission factor must be applied to all reporting facilities for the owner or operator.

(7) . For compressor sources measured according to paragraph (p)(1)(ii) of this section, you must use the continuous volumetric emission measurements taken as specified in paragraph (p)(3) of this section and calculate annual volumetric GHG emissions associated with the compressor source using equation W-29A to this section.

(8) For manifolded groups of compressor sources measured according to paragraph (p)(1)(iii) of this section, you must calculate annual GHG emissions using equation W-29B to this section. If the reciprocating compressors included in the manifolded group of compressor sources share the manifold with centrifugal compressors, you must follow the procedures in either this paragraph (p)(8) or paragraph (o)(8) of this section to calculate emissions from the manifolded group of compressor sources.

(9) . For a manifolded group of compressor sources measured according to paragraph (p)(1)(iv) of this section, you must use the continuous volumetric emission measurements taken as specified in paragraph (p)(5) of this section and calculate annual volumetric GHG emissions associated with each manifolded group of compressor sources using equation W-29C to this section. If the reciprocating compressors included in the manifolded group of compressor sources share the manifold with centrifugal compressors, you must follow the procedures in either this paragraph (p)(9) or paragraph (o)(9) of this section to calculate emissions from the manifolded group of compressor sources.

(10) . You must calculate volumetric emissions from reciprocating compressors at an onshore petroleum and natural gas production facility or an onshore petroleum and natural gas gathering and boosting facility as specified in paragraphs (p)(10)(i) through (iv) of this section, as applicable.

(i) For all reciprocating compressors at an onshore petroleum and natural gas production facility or an onshore petroleum and natural gas gathering and boosting facility that are subject to the reciprocating compressor standards in § 60.5385b of this chapter or an applicable approved state plan or applicable Federal plan in part 62 of this chapter, you must conduct the volumetric emission measurements as required by § 60.5385b(b) and (c) of this chapter or an applicable approved state plan or applicable Federal plan in part 62 of this chapter, conduct any additional volumetric emission measurements specified in paragraph (p)(1) of this section using methods specified in paragraphs (p)(2) through (5) of this section (based on the compressor mode (as defined in § 98.238) in which the compressor was found at the time of measurement), and calculate emissions as specified in paragraphs (p)(6) through (9) of this section. Conduct all measurements required by this paragraph (p)(10)(i) at the frequency specified by § 60.5385b(a) of this chapter or an applicable approved state plan or applicable Federal plan in part 62 of this chapter. For any reporting year in which measuring at the frequency specified by § 60.5385b(a) of this chapter results in measurement not being required for a subject compressor, calculate emissions for all mode-source combinations as specified in paragraph (p)(6)(ii) of this section.

(ii) For all reciprocating compressors at an onshore petroleum and natural gas production facility or an onshore petroleum and natural gas gathering and boosting facility that are not subject to the reciprocating compressor standards in § 60.5385b of this chapter or an applicable approved state plan or applicable Federal plan in part 62 of this chapter, you may elect to conduct volumetric emission measurements specified in paragraph (p)(1) of this section using methods specified in paragraphs (p)(2) through (5) of this section (based on the compressor mode (as defined in § 98.238) in which the compressor was found at the time of measurement), and calculate emissions as specified in paragraphs (p)(6) through (9) of this section.

(iii) For all reciprocating compressors at an onshore petroleum and natural gas production facility or an onshore petroleum and natural gas gathering and boosting facility for which paragraph (p)(10)(i) of this section does not apply, and you do not elect to conduct volumetric emission measurements specified in paragraph (p)(1) of this section, you must calculate total atmospheric rod packing emissions from all reciprocating compressors at either an onshore petroleum and natural gas production facility or an onshore petroleum and natural gas gathering and boosting facility using equation W-29D to this section. Reciprocating compressor rod packing emissions that are routed to a flare, combustion, or vapor recovery system are not required to be determined under this paragraph (p).

(iv) For all reciprocating compressors at an onshore petroleum and natural gas production facility or an onshore petroleum and natural gas gathering and boosting facility for which paragraph (p)(10)(i) of this section does not apply, you must calculate rod packing vent emissions from each reciprocating compressor using equation W-29E to this section. Reciprocating compressor rod packing emissions that are routed to a flare, combustion, or vapor recovery system are not required to be determined under this paragraph (p).

(11) You must calculate both CH4 and CO2 mass emissions from volumetric emissions using calculations in paragraph (v) of this section.

(o) If you are required to report emissions from centrifugal compressor venting as specified in § 98.232(d)(2), (e)(2), (f)(2), (g)(2), and (h)(2), you must conduct volumetric emission measurements specified in paragraph (o)(1) of this section using methods specified in paragraphs (o)(2) through (5) of this section; perform calculations specified in paragraphs (o)(6) through (9) of this section; and calculate CH4 and CO2 mass emissions as specified in paragraph (o)(11) of this section. If you are required to report emissions from centrifugal compressor venting at an onshore petroleum and natural gas production facility as specified in § 98.232(c)(19) or an onshore petroleum and natural gas gathering and boosting facility as specified in § 98.232(j)(8), you must calculate volumetric emissions as specified in paragraph (o)(10) of this section and calculate CH4 and CO2 mass emissions as specified in paragraph (o)(11) of this section. If emissions from a compressor source are routed to a flare, paragraphs (o)(1) through (11) of this section do not apply and instead you must calculate CH4, CO2, and N2O emissions as specified in paragraph (n) of this section and report emissions from the flare as specified in § 98.236(n). If emissions from a compressor source are routed to combustion, paragraphs (o)(1) through (11) of this section do not apply and instead you must calculate and report emissions as specified in subpart C of this part or paragraph (z) of this section, as applicable. If emissions from a compressor source are routed to a vapor recovery system, paragraphs (o)(1) through (11) of this section do not apply.

(1) You must conduct volumetric emission measurements on each centrifugal compressor as specified in this paragraph. Compressor sources (as defined in § 98.238) without manifolded vents must use a measurement method specified in paragraph (o)(1)(i) or (ii) of this section. Manifolded compressor sources (as defined in § 98.238) must use a measurement method specified in paragraph (o)(1)(i), (ii), (iii), or (iv) of this section.

(i) Measure venting from each compressor according to either paragraph (o)(1)(i)(A), (B), or (C) of this section at least once annually, based on the compressor mode (as defined in § 98.238) in which the compressor was found at the time of measurement, except as specified in paragraph (o)(1)(i)(D) of this section. If additional measurements beyond the required annual testing are performed (including duplicate measurements or measurement of additional operating modes), then all measurements satisfying the applicable monitoring and QA/QC that is required by this paragraph (o) must be used in the calculations specified in this section.

(A) For a compressor measured in operating-mode, you must measure volumetric emissions from blowdown valve leakage through the blowdown vent as specified in paragraph (o)(2)(i) of this section, measure volumetric emissions from wet seal oil degassing vents as specified in paragraph (o)(2)(ii) of this section if the compressor has wet seal oil degassing vents, and measure volumetric emissions from dry seal vents as specified in paragraph (o)(2)(iii) of this section if the compressor has dry seals.

(B) For a compressor measured in not-operating-depressurized-mode, you must measure volumetric emissions from isolation valve leakage as specified in paragraph (o)(2)(i) of this section. If a compressor is not operated and has blind flanges in place throughout the reporting period, measurement is not required in this compressor mode.

(C) For a compressor measured in standby-pressurized-mode, you must measure volumetric emissions from blowdown valve leakage through the blowdown vent as specified in paragraph (o)(2)(i) of this section, measure volumetric emissions from wet seal oil degassing vents as specified in paragraph (o)(2)(ii) of this section if the compressor has wet seal oil degassing vents, and measure volumetric emissions from dry seal vents as specified in paragraph (o)(2)(iii) of this section if the compressor has dry seals.

(D) An annual as found measurement is not required in the first year of operation for any new compressor that begins operation after as found measurements have been conducted for all existing compressors. For only the first year of operation of new compressors, calculate emissions according to paragraph (o)(6)(ii) of this section.

(ii) Instead of measuring the compressor source according to paragraph (o)(1)(i) of this section for a given compressor, you may elect to continuously measure volumetric emissions from a compressor source as specified in paragraph (o)(3) of this section.

(iii) For a compressor source that is part of a manifolded group of compressor sources (as defined in § 98.238), instead of measuring the compressor source according to paragraph (o)(1)(i), (ii), or (iv) of this section, you may elect to measure combined volumetric emissions from the manifolded group of compressor sources by conducting measurements at the common vent stack as specified in paragraph (o)(4) of this section. The measurements must be conducted at the frequency specified in paragraphs (o)(1)(iii)(A) and (B) of this section.

(A) A minimum of one measurement must be taken for each manifolded group of compressor sources in a calendar year.

(B) The measurement may be performed while the compressors are in any compressor mode.

(iv) For a compressor source that is part of a manifolded group of compressor sources, instead of measuring the compressor source according to paragraph (o)(1)(i), (ii), or (iii) of this section, you may elect to continuously measure combined volumetric emissions from the manifolded group of compressor sources as specified in paragraph (o)(5) of this section.

(2) . If conducting measurements for each compressor source, you must determine the volumetric emissions from blowdown valves and isolation valves as specified in paragraph (o)(2)(i) of this section, the volumetric emissions from wet seal oil degassing vents as specified in paragraph (o)(2)(ii) of this section, and the volumetric emissions from dry seal vents as specified in paragraph (o)(2)(iii) of this section.

(i) For blowdown valves on compressors in operating-mode or in standby-pressurized-mode and for isolation valves on compressors in not-operating-depressurized-mode, determine the volumetric emissions using one of the methods specified in paragraphs (o)(2)(i)(A) through (D) of this section.

(A) Determine the volumetric flow at standard conditions from the blowdown vent using calibrated bagging or high volume sampler according to methods set forth in § 98.234(c) and § 98.234(d), respectively.

(B) Determine the volumetric flow at standard conditions from the blowdown vent using a temporary meter such as a vane anemometer according to methods set forth in § 98.234(b).

(C) Use an acoustic leak detection device according to methods set forth in § 98.234(a)(5).

(D) You may choose to use any of the methods set forth in § 98.234(a) to screen for emissions. If emissions are detected using the methods set forth in § 98.234(a), then you must use one of the methods specified in paragraph (o)(2)(i)(A) through (C) of this section. If emissions are not detected using the methods in § 98.234(a), then you may assume that the volumetric emissions are zero. For the purposes of this paragraph, when using any of the methods in § 98.234(a), emissions are detected whenever a leak is detected according to the methods.

(ii) For wet seal oil degassing vents in operating-mode or in standby-pressurized-mode, determine volumetric flow at standard conditions, using one of the methods specified in paragraphs (o)(2)(ii)(A) through (C) of this section. You must quantitatively measure the volumetric flow for wet seal oil degassing vent; you may not use screening methods set forth in § 98.234(a) to screen for emissions for the wet seal oil degassing vent.

(A) Use a temporary meter such as a vane anemometer or permanent flow meter according to methods set forth in § 98.234(b).

(B) Use calibrated bags according to methods set forth in § 98.234(c).

(C) Use a high volume sampler according to methods set forth in § 98.234(d).

(iii) For dry seal vents in operating-mode or in standby-pressurized-mode, determine volumetric flow at standard conditions from each dry seal vent using one of the methods specified in paragraphs (o)(2)(iii)(A) through (D) of this section. The measurement should be conducted on the compressor side dry seal. If a compressor has more than one dry seal vent, determine the aggregate dry seal vent volumetric flow for the compressor as the sum of the volumetric flows determined for each dry seal vent on the compressor.

(A) Use a temporary meter such as a vane anemometer or permanent flow meter according to methods set forth in § 98.234(b).

(B) Use calibrated bags according to methods set forth in § 98.234(c).

(C) Use a high volume sampler according to methods set forth in § 98.234(d).

(D) You may choose to use any of the methods set forth in § 98.234(a)(1) through (3) to screen for emissions. If emissions are detected using one of these specified methods, then you must use one of the methods specified in paragraph (o)(2)(iii)(A) through (C) of this section. If emissions are not detected using the methods in § 98.234(a)(1) through (3), then you may assume that the volumetric emissions are zero. For the purposes of this paragraph, when using any of the methods in § 98.234(a), emissions are detected whenever a leak is detected according to the methods. Acoustic leak detection is only applicable for through-valve leakage and is not applicable for screening dry seal vents.

(3) If you elect to conduct continuous volumetric emission measurements for an individual compressor source as specified in paragraph (o)(1)(ii) of this section, you must measure volumetric emissions as specified in paragraphs (o)(3)(i) and (ii) of this section.

(i) Continuously measure the volumetric flow for the individual compressor source at standard conditions using a permanent meter according to methods set forth in § 98.234(b).

(ii) If compressor blowdown emissions are included in the metered emissions specified in paragraph (o)(3)(i) of this section, the compressor blowdown emissions may be included with the reported emissions for the compressor source and do not need to be calculated separately using the method specified in paragraph (i) of this section for blowdown vent stacks.

(4) If conducting measurements for a manifolded group of compressor sources, you must measure volumetric emissions as specified in paragraphs (o)(4)(i) and (ii) of this section.

(i) Measure at a single point in the manifold downstream of all compressor inputs and, if practical, prior to comingling with other non-compressor emission sources.

(ii) Determine the volumetric flow at standard conditions from the common stack using one of the methods specified in paragraphs (o)(4)(ii)(A) through (F) of this section.

(A) A temporary meter such as a vane anemometer according the methods set forth in § 98.234(b).

(B) Calibrated bagging according to methods set forth in § 98.234(c).

(C) A high volume sampler according to methods set forth § 98.234(d).

(D) [Reserved]

(E) You may choose to use any of the methods set forth in § 98.234(a)(1) through (3) to screen for emissions. If emissions are detected using one of these methods, then you must use one of the methods specified in paragraph (o)(4)(ii)(A) through (D) of this section. If emissions are not detected using the methods in § 98.234(a)(1) through (3), then you may assume that the volumetric emissions are zero. For the purposes of this paragraph, when using any of the methods in § 98.234(a), emissions are detected whenever a leak is detected according to the method. Acoustic leak detection is only applicable for through-valve leakage and is not applicable for screening a manifolded group of compressor sources.

(F) If one of the screening methods specified in § 98.234(a)(1) through (3) identifies a leak in a manifolded group of centrifugal compressor sources, you may use acoustic leak detection, according to § 98.234(a)(5), to identify the source of the leak. You must use one of the methods specified in paragraphs (o)(4)(ii)(A) through (D) of this section to quantify emissions from the identified source.

(5) If you elect to conduct continuous volumetric emission measurements for a manifolded group of compressor sources as specified in paragraph (o)(1)(iv) of this section, you must measure volumetric emissions as specified in paragraphs (o)(5)(i) through (iii) of this section.

(i) Measure at a single point in the manifold downstream of all compressor inputs and, if practical, prior to comingling with other non-compressor emission sources.

(ii) Continuously measure the volumetric flow for the manifolded group of compressor sources at standard conditions using a permanent meter according to methods set forth in § 98.234(b).

(iii) If compressor blowdown emissions are included in the metered emissions specified in paragraph (o)(5)(ii) of this section, the compressor blowdown emissions may be included with the reported emissions for the manifolded group of compressor sources and do not need to be calculated separately using the method specified in paragraph (i) of this section for blowdown vent stacks.

(6) . For compressor sources measured according to paragraph (o)(1)(i) of this section, you must calculate annual GHG emissions from the compressor sources as specified in paragraphs (o)(6)(i) through (iv) of this section.

(i) Using equation W-21 to this section, calculate the annual volumetric GHG emissions for each centrifugal compressor mode-source combination specified in paragraphs (o)(1)(i)(A) through (C) of this section that was measured during the reporting year.

(ii) Using equation W-22 to this section, calculate the annual volumetric GHG emissions from each centrifugal compressor mode-source combination specified in paragraphs (o)(1)(i)(A) through (C) of this section that was not measured during the reporting year.

(iii) Using equation W-23 to this section, develop an emission factor for each compressor mode-source combination specified in paragraphs (o)(1)(i)(A) through (C) of this section. These emission factors must be calculated annually and used in equation W-22 to this section to determine volumetric emissions from a centrifugal compressor in the mode- source combinations that were not measured in the reporting year.

(iv) The reporter emission factor in equation W-23 to this section may be calculated by using all measurements from a single owner or operator instead of only using measurements from a single facility. If you elect to use this option, the reporter emission factor must be applied to all reporting facilities for the owner or operator.

(7) . For compressor sources measured according to paragraph (o)(1)(ii) of this section, you must use the continuous volumetric emission measurements taken as specified in paragraph (o)(3) of this section and calculate annual volumetric GHG emissions associated with the compressor source using equation W-24A to this section.

(8) . For manifolded groups of compressor sources measured according to paragraph (o)(1)(iii) of this section, you must calculate annual volumetric GHG emissions using equation W-24B to this section. If the centrifugal compressors included in the manifolded group of compressor sources share the manifold with reciprocating compressors, you must follow the procedures in either this paragraph (o)(8) or paragraph (p)(8) of this section to calculate emissions from the manifolded group of compressor sources.

(9) For a manifolded group of compressor sources measured according to paragraph (o)(1)(iv) of this section, you must use the continuous volumetric emission measurements taken as specified in paragraph (o)(5) of this section and calculate annual volumetric GHG emissions associated with each manifolded group of compressor sources using equation W-24C to this section. If the centrifugal compressors included in the manifolded group of compressor sources share the manifold with reciprocating compressors, you must follow the procedures in either this paragraph (o)(9) or paragraph (p)(9) of this section to calculate emissions from the manifolded group of compressor sources.

(10) You must calculate volumetric emissions from centrifugal compressors at an onshore petroleum and natural gas production facility or an onshore petroleum and natural gas gathering and boosting facility as specified in paragraphs (o)(10)(i) through (iv), as applicable.

(i) For all centrifugal compressors at an onshore petroleum and natural gas production facility or an onshore petroleum and natural gas gathering and boosting facility that are subject to the centrifugal compressor standards in § 60.5380b of this chapter or an applicable approved state plan or applicable Federal plan in part 62 of this chapter for dry seals and self-contained wet seals, you must conduct the volumetric emission measurements as required by § 60.5380b(a)(5) of this chapter or an applicable approved state plan or applicable Federal plan in part 62 of this chapter, conduct all additional volumetric emission measurements specified in paragraph (o)(1) of this section using methods specified in paragraphs (o)(2) through (5) of this section (based on the compressor mode (as defined in § 98.238) in which the compressor was found at the time of measurement), and calculate emissions as specified in paragraphs (o)(6) through (9) of this section. Conduct all measurements required by this paragraph (o)(10)(i) at the frequency specified by § 60.5380b(a)(4) of this chapter or an applicable approved state plan or applicable Federal plan in part 62 of this chapter. For any reporting year in which measuring at the frequency specified by § 60.5380b(a)(4) of this chapter results in measurement not being required for a subject compressor, calculate emissions for all mode-source combinations as specified in paragraph (o)(6)(ii) of this section.

(ii) For all centrifugal compressors at an onshore petroleum and natural gas production facility or an onshore petroleum and natural gas gathering and boosting facility that are not subject to the centrifugal compressor standards in § 60.5380b of this chapter or an applicable approved state plan or applicable Federal plan in part 62 of this chapter for dry seals and self-contained wet seals, you may elect to conduct the volumetric emission measurements specified in paragraph (o)(1) of this section using methods specified in paragraphs (o)(2) through (5) of this section (based on the compressor mode (as defined in § 98.238) in which the compressor was found at the time of measurement), and calculate emissions as specified in paragraphs (o)(6) through (9) of this section.

(iii) For all centrifugal compressors at an onshore petroleum and natural gas production facility or an onshore petroleum and natural gas gathering and boosting facility for which paragraph (o)(10)(i) of this section does not apply and you do not elect to conduct the volumetric measurements specified in paragraph (o)(1) of this section, you must calculate total atmospheric wet seal oil degassing vent emissions from all centrifugal compressors at either an onshore petroleum and natural gas production facility or an onshore petroleum and natural gas gathering and boosting facility using equation W-25A to this section. Emissions from centrifugal compressor wet seal oil degassing vents that are routed to a flare, combustion, or vapor recovery system are not required to be determined under this paragraph (o).

(iv) For all centrifugal compressors at an onshore petroleum and natural gas production facility or an onshore petroleum and natural gas gathering and boosting facility for which paragraph (o)(10)(i) of this section does not apply, and you do not elect to conduct the volumetric measurements specified in paragraph (o)(1) of this section, you must calculate wet seal oil degassing vent emissions from each centrifugal compressor using equation W-25B to this section. Emissions from centrifugal compressor wet seal oil degassing vents that are routed to a flare, combustion, or vapor recovery system are not required to be determined under this paragraph (o).

(11) . You must calculate both CH4 and CO2 mass emissions from volumetric emissions using calculations in paragraph (v) of this section.

(i) For the components listed in § 98.232(e)(7), (f)(5), (g)(4), and (h)(5), that are not subject to the well site or compressor station fugitive emissions standards in § 60.5397a of this chapter, the fugitive emissions standards for well sites, centralized production facilities, and compressor stations in § 60.5397b or 60.5398b of this chapter, or an applicable approved state plan or applicable Federal plan in part 62 of this chapter, you must conduct surveys using any of the leak detection methods listed in § 98.234(a) and calculate equipment leak emissions using the procedures specified in either paragraph (q)(2) or (3) of this section.

(2) You must indicate whether your facility contains any of the component types subject to or complying with § 98.233(q) that are listed in § 98.232(c)(21), (d)(7), (e)(7) or (8), (f)(5) through (8), (g)(4), (g)(6) or (7), (h)(5), (h)(7) or (8), (i)(1), (j)(10), (m)(3)(ii) or (m)(4)(ii) for your facility's industry segment. For each component type and leak detection method combination that is located at your well-pad site, gathering and boosting site, or facility, you must report the information specified in paragraphs (q)(2)(i) through (ix) of this section. If a component type is located at your well-pad site, gathering and boosting site, or facility and no leaks were identified from that component, then you must report the information in paragraphs (q)(2)(i) through (ix) of this section but report a zero (“0”) for the information required according to paragraphs (q)(2)(vi) through (ix) of this section. If you used Calculation Method 1 (leaker factor emission calculation methodology) for some complete leak surveys and used Calculation Method 2 (leaker measurement methodology) for some complete leak surveys, you must report the information specified in paragraphs (q)(2)(i) through (ix) of this section separately for component surveys using Calculation Method 1 and Calculation Method 2.

(i) Well-pad ID (for the onshore petroleum and natural gas production industry segment only) or gathering and boosting site ID (for the onshore petroleum and natural gas gathering and boosting industry segment only).

(iii) Leak detection method used for the screening survey (e.g., Method 21 as specified in § 98.234(a)(2)(i); Method 21 as specified in § 98.234(a)(2)(ii); and OGI and other leak detection methods as specified in § 98.234(a)(1), (3), or (5)).

(iv) Emission factor or measurement method used (e.g., default emission factor; facility-specific emission factor developed according to § 98.233(q)(4); or direct measurement according to § 98.233(q)(3)).

(vi) Total number of the surveyed component types by leak detection method that were identified as leaking in the calendar year (“xp” in equation W-30 to § 98.233 for the component type or the number of leaks measured for the specified component type according to the provisions in § 98.233(q)(3)).

(vii) Average time the surveyed components are assumed to be leaking and operational, in hours (average of “Tp,z” from equation W-30 to § 98.233 for the component type or average duration of leaks for the specified component type determined according to the provisions in § 98.233(q)(3)(ii)).

(viii) Annual CO2 emissions, in metric tons CO2, for the component type as calculated using equation W-30 to § 98.233 or § 98.233(q)(3)(vii) (for surveyed components only).

(ix) Annual CH4 emissions, in metric tons CH4, for the component type as calculated using equation W-30 to § 98.233 or § 98.233(q)(3)(vii) (for surveyed components only).

(B) If you elect to use a leak detection method in § 98.234(a) for the surveyed component types in § 98.232(e)(8), (f)(6) and (8), (g)(7), and (h)(8), then you must use the procedures in either paragraph (q)(2) or (3) of this section to calculate those emissions.

(2) You must indicate whether your facility contains any of the component types subject to or complying with § 98.233(q) that are listed in § 98.232(c)(21), (d)(7), (e)(7) or (8), (f)(5) through (8), (g)(4), (g)(6) or (7), (h)(5), (h)(7) or (8), (i)(1), (j)(10), (m)(3)(ii) or (m)(4)(ii) for your facility's industry segment. For each component type and leak detection method combination that is located at your well-pad site, gathering and boosting site, or facility, you must report the information specified in paragraphs (q)(2)(i) through (ix) of this section. If a component type is located at your well-pad site, gathering and boosting site, or facility and no leaks were identified from that component, then you must report the information in paragraphs (q)(2)(i) through (ix) of this section but report a zero (“0”) for the information required according to paragraphs (q)(2)(vi) through (ix) of this section. If you used Calculation Method 1 (leaker factor emission calculation methodology) for some complete leak surveys and used Calculation Method 2 (leaker measurement methodology) for some complete leak surveys, you must report the information specified in paragraphs (q)(2)(i) through (ix) of this section separately for component surveys using Calculation Method 1 and Calculation Method 2.

(i) Well-pad ID (for the onshore petroleum and natural gas production industry segment only) or gathering and boosting site ID (for the onshore petroleum and natural gas gathering and boosting industry segment only).

(iii) Leak detection method used for the screening survey (e.g., Method 21 as specified in § 98.234(a)(2)(i); Method 21 as specified in § 98.234(a)(2)(ii); and OGI and other leak detection methods as specified in § 98.234(a)(1), (3), or (5)).

(iv) Emission factor or measurement method used (e.g., default emission factor; facility-specific emission factor developed according to § 98.233(q)(4); or direct measurement according to § 98.233(q)(3)).

(vi) Total number of the surveyed component types by leak detection method that were identified as leaking in the calendar year (“xp” in equation W-30 to § 98.233 for the component type or the number of leaks measured for the specified component type according to the provisions in § 98.233(q)(3)).

(vii) Average time the surveyed components are assumed to be leaking and operational, in hours (average of “Tp,z” from equation W-30 to § 98.233 for the component type or average duration of leaks for the specified component type determined according to the provisions in § 98.233(q)(3)(ii)).

(viii) Annual CO2 emissions, in metric tons CO2, for the component type as calculated using equation W-30 to § 98.233 or § 98.233(q)(3)(vii) (for surveyed components only).

(ix) Annual CH4 emissions, in metric tons CH4, for the component type as calculated using equation W-30 to § 98.233 or § 98.233(q)(3)(vii) (for surveyed components only).

(2) You must indicate whether your facility contains any of the component types subject to or complying with § 98.233(q) that are listed in § 98.232(c)(21), (d)(7), (e)(7) or (8), (f)(5) through (8), (g)(4), (g)(6) or (7), (h)(5), (h)(7) or (8), (i)(1), (j)(10), (m)(3)(ii) or (m)(4)(ii) for your facility's industry segment. For each component type and leak detection method combination that is located at your well-pad site, gathering and boosting site, or facility, you must report the information specified in paragraphs (q)(2)(i) through (ix) of this section. If a component type is located at your well-pad site, gathering and boosting site, or facility and no leaks were identified from that component, then you must report the information in paragraphs (q)(2)(i) through (ix) of this section but report a zero (“0”) for the information required according to paragraphs (q)(2)(vi) through (ix) of this section. If you used Calculation Method 1 (leaker factor emission calculation methodology) for some complete leak surveys and used Calculation Method 2 (leaker measurement methodology) for some complete leak surveys, you must report the information specified in paragraphs (q)(2)(i) through (ix) of this section separately for component surveys using Calculation Method 1 and Calculation Method 2.

(i) Well-pad ID (for the onshore petroleum and natural gas production industry segment only) or gathering and boosting site ID (for the onshore petroleum and natural gas gathering and boosting industry segment only).

(iii) Leak detection method used for the screening survey (e.g., Method 21 as specified in § 98.234(a)(2)(i); Method 21 as specified in § 98.234(a)(2)(ii); and OGI and other leak detection methods as specified in § 98.234(a)(1), (3), or (5)).

(iv) Emission factor or measurement method used (e.g., default emission factor; facility-specific emission factor developed according to § 98.233(q)(4); or direct measurement according to § 98.233(q)(3)).

(vi) Total number of the surveyed component types by leak detection method that were identified as leaking in the calendar year (“xp” in equation W-30 to § 98.233 for the component type or the number of leaks measured for the specified component type according to the provisions in § 98.233(q)(3)).

(vii) Average time the surveyed components are assumed to be leaking and operational, in hours (average of “Tp,z” from equation W-30 to § 98.233 for the component type or average duration of leaks for the specified component type determined according to the provisions in § 98.233(q)(3)(ii)).

(viii) Annual CO2 emissions, in metric tons CO2, for the component type as calculated using equation W-30 to § 98.233 or § 98.233(q)(3)(vii) (for surveyed components only).

(ix) Annual CH4 emissions, in metric tons CH4, for the component type as calculated using equation W-30 to § 98.233 or § 98.233(q)(3)(vii) (for surveyed components only).

(B) If you elect to use a leak detection method in § 98.234(a) for the surveyed component types in § 98.232(e)(8), (f)(6) and (8), (g)(7), and (h)(8), then you must use the procedures in either paragraph (q)(2) or (3) of this section to calculate those emissions.

(2) You must indicate whether your facility contains any of the component types subject to or complying with § 98.233(q) that are listed in § 98.232(c)(21), (d)(7), (e)(7) or (8), (f)(5) through (8), (g)(4), (g)(6) or (7), (h)(5), (h)(7) or (8), (i)(1), (j)(10), (m)(3)(ii) or (m)(4)(ii) for your facility's industry segment. For each component type and leak detection method combination that is located at your well-pad site, gathering and boosting site, or facility, you must report the information specified in paragraphs (q)(2)(i) through (ix) of this section. If a component type is located at your well-pad site, gathering and boosting site, or facility and no leaks were identified from that component, then you must report the information in paragraphs (q)(2)(i) through (ix) of this section but report a zero (“0”) for the information required according to paragraphs (q)(2)(vi) through (ix) of this section. If you used Calculation Method 1 (leaker factor emission calculation methodology) for some complete leak surveys and used Calculation Method 2 (leaker measurement methodology) for some complete leak surveys, you must report the information specified in paragraphs (q)(2)(i) through (ix) of this section separately for component surveys using Calculation Method 1 and Calculation Method 2.

(i) Well-pad ID (for the onshore petroleum and natural gas production industry segment only) or gathering and boosting site ID (for the onshore petroleum and natural gas gathering and boosting industry segment only).

(iii) Leak detection method used for the screening survey (e.g., Method 21 as specified in § 98.234(a)(2)(i); Method 21 as specified in § 98.234(a)(2)(ii); and OGI and other leak detection methods as specified in § 98.234(a)(1), (3), or (5)).

(iv) Emission factor or measurement method used (e.g., default emission factor; facility-specific emission factor developed according to § 98.233(q)(4); or direct measurement according to § 98.233(q)(3)).

(vi) Total number of the surveyed component types by leak detection method that were identified as leaking in the calendar year (“xp” in equation W-30 to § 98.233 for the component type or the number of leaks measured for the specified component type according to the provisions in § 98.233(q)(3)).

(vii) Average time the surveyed components are assumed to be leaking and operational, in hours (average of “Tp,z” from equation W-30 to § 98.233 for the component type or average duration of leaks for the specified component type determined according to the provisions in § 98.233(q)(3)(ii)).

(viii) Annual CO2 emissions, in metric tons CO2, for the component type as calculated using equation W-30 to § 98.233 or § 98.233(q)(3)(vii) (for surveyed components only).

(ix) Annual CH4 emissions, in metric tons CH4, for the component type as calculated using equation W-30 to § 98.233 or § 98.233(q)(3)(vii) (for surveyed components only).

(a) You must report CO2, CH4, and N2O emissions from each industry segment specified in paragraphs (b) through (j) and (m) of this section, CO2, CH4, and N2O emissions from each flare as specified in paragraphs (b) through (j) of this section, and stationary and portable combustion emissions as applicable as specified in paragraph (k) of this section. You must also report the information specified in paragraph (l) of this section, as applicable.

(p) If you are required to report emissions from reciprocating compressor venting as specified in § 98.232(d)(1), (e)(1), (f)(1), (g)(1), and (h)(1), you must conduct volumetric emission measurements specified in paragraph (p)(1) of this section using methods specified in paragraphs (p)(2) through (5) of this section; perform calculations specified in paragraphs (p)(6) through (9) of this section; and calculate CH4 and CO2 mass emissions as specified in paragraph (p)(11) of this section. If you are required to report emissions from reciprocating compressor venting at an onshore petroleum and natural gas production facility as specified in § 98.232(c)(11) or an onshore petroleum and natural gas gathering and boosting facility as specified in § 98.232(j)(9), you must calculate volumetric emissions as specified in paragraph (p)(10) of this section and calculate CH4 and CO2 mass emissions as specified in paragraph (p)(11) of this section. If emissions from a compressor source are routed to a flare, paragraphs (p)(1) through (11) of this section do not apply and instead you must calculate CH4, CO2, and N2O emissions as specified in paragraph (n) of this section and report emissions from the flare as specified in § 98.236(n). If emissions from a compressor source are routed to combustion, paragraphs (p)(1) through (11) of this section do not apply and instead you must calculate and report emissions as specified in subpart C of this part or paragraph (z) of this section, as applicable. If emissions from a compressor source are routed to a vapor recovery system, paragraphs (p)(1) through (11) of this section do not apply.

(1) You must conduct volumetric emission measurements on each reciprocating compressor as specified in this paragraph. Compressor sources (as defined in § 98.238) without manifolded vents must use a measurement method specified in paragraph (p)(1)(i) or (ii) of this section. Manifolded compressor sources (as defined in § 98.238) must use a measurement method specified in paragraph (p)(1)(i), (ii), (iii), or (iv) of this section.

(i) Measure venting from each compressor according to either paragraph (p)(1)(i)(A), (B), or (C) of this section at least once annually, based on the compressor mode (as defined in § 98.238) in which the compressor was found at the time of measurement, except as specified in paragraph (p)(1)(i)(D) of this section. If additional measurements beyond the required annual testing are performed (including duplicate measurements or measurement of additional operating modes), then all measurements satisfying the applicable monitoring and QA/QC that is required by this paragraph (p) must be used in the calculations specified in this section.

(A) For a compressor measured in operating-mode, you must measure volumetric emissions from blowdown valve leakage through the blowdown vent as specified in paragraph (p)(2)(i) of this section, and measure volumetric emissions from reciprocating rod packing as specified in paragraph (p)(2)(ii) or (iii) of this section, as applicable.

(B) For a compressor measured in not-operating-depressurized-mode, you must measure volumetric emissions from isolation valve leakage as specified in paragraph (p)(2)(i) of this section. If a compressor is not operated and has blind flanges in place throughout the reporting period, measurement is not required in this compressor mode.

(C) For a compressor measured in standby-pressurized-mode, you must measure volumetric emissions from blowdown valve leakage through the blowdown vent as specified in paragraph (p)(2)(i) of this section and measure volumetric emissions from reciprocating rod packing as specified in paragraph (p)(2)(ii) or (iii) of this section, as applicable.

(D) An annual as found measurement is not required in the first year of operation for any new compressor that begins operation after as found measurements have been conducted for all existing compressors. For only the first year of operation of new compressors, calculate emissions according to paragraph (p)(6)(ii) of this section.

(ii) Instead of measuring the compressor source according to paragraph (p)(1)(i) of this section for a given compressor, you may elect to continuously measure volumetric emissions from a compressor source as specified in paragraph (p)(3) of this section.

(iii) For a compressor source that is part of a manifolded group of compressor sources (as defined in § 98.238), instead of measuring the compressor source according to paragraph (p)(1)(i), (ii), or (iv) of this section, you may elect to measure combined volumetric emissions from the manifolded group of compressor sources by conducting measurements at the common vent stack as specified in paragraph (p)(4) of this section. The measurements must be conducted at the frequency specified in paragraphs (p)(1)(iii)(A) and (B) of this section.

(A) A minimum of one measurement must be taken for each manifolded group of compressor sources in a calendar year.

(B) The measurement may be performed while the compressors are in any compressor mode.

(iv) For a compressor source that is part of a manifolded group of compressor sources, instead of measuring the compressor source according to paragraph (p)(1)(i), (ii), or (iii) of this section, you may elect to continuously measure combined volumetric emissions from the manifolded group of compressors sources as specified in paragraph (p)(5) of this section.

(2) . If conducting measurements for each compressor source, you must determine the volumetric emissions from blowdown valves and isolation valves as specified in paragraph (p)(2)(i) of this section. You must determine the volumetric emissions from reciprocating rod packing as specified in paragraph (p)(2)(ii) or (iii) of this section, as applicable.

(i) and for isolation valves on compressors in not-operating-depressurized-mode, determine the volumetric emissions using one of the methods specified in paragraphs (p)(2)(i)(A) through (D) of this section.

(A) Determine the volumetric flow at standard conditions from the blowdown vent using calibrated bagging or high volume sampler according to methods set forth in § 98.234(c) and (d), respectively.

(B) Determine the volumetric flow at standard conditions from the blowdown vent using a temporary meter such as a vane anemometer, according to methods set forth in § 98.234(b).

(C) Use an acoustic leak detection device according to methods set forth in § 98.234(a)(5).

(D) You may choose to use any of the methods set forth in § 98.234(a) to screen for emissions. If emissions are detected using the methods set forth in § 98.234(a), then you must use one of the methods specified in paragraphs (p)(2)(i)(A) through (C) of this section. If emissions are not detected using the methods in § 98.234(a), then you may assume that the volumetric emissions are zero. For the purposes of this paragraph, when using any of the methods in § 98.234(a), emissions are detected whenever a leak is detected according to the method.

(ii) For reciprocating rod packing equipped with an open-ended vent line on compressors in operating-mode or standby-pressurized-mode, determine the volumetric emissions using one of the methods specified in paragraphs (p)(2)(ii)(A) through (C) of this section.

(A) Determine the volumetric flow at standard conditions from the open-ended vent line using calibrated bagging or high volume sampler according to methods set forth in § 98.234(c) and (d), respectively.

(B) Determine the volumetric flow at standard conditions from the open-ended vent line using a temporary meter such as a vane anemometer, according to methods set forth in § 98.234(b).

(C) You may choose to use any of the methods set forth in § 98.234(a)(1) through (3) to screen for emissions. If emissions are detected using one of these specified methods, then you must use one of the methods specified in paragraphs (p)(2)(ii)(A) and (B) of this section. If emissions are not detected using the methods in § 98.234(a)(1) through (3), then you may assume that the volumetric emissions are zero. For the purposes of this paragraph (p)(2)(ii)(C), when using any of the methods in § 98.234(a), emissions are detected whenever a leak is detected according to the method. Acoustic leak detection is only applicable for through-valve leakage and is not applicable for screening or measuring rod packing emissions.

(iii) For reciprocating rod packing not equipped with an open-ended vent line on compressors in operating-mode, you must determine the volumetric emissions using the method specified in paragraphs (p)(2)(iii)(A) and (B) of this section.

(A) You must use the methods described in § 98.234(a)(1) through (3) to conduct annual leak detection of equipment leaks from the packing case into an open distance piece, or for compressors with a closed distance piece, conduct annual detection of gas emissions from the rod packing vent, distance piece vent, compressor crank case breather cap, or other vent emitting gas from the rod packing. Acoustic leak detection is only applicable for through-valve leakage and is not applicable for screening rod packing emissions.

(B) You must measure emissions found in paragraph (p)(2)(iii)(A) of this section using an appropriate meter, calibrated bag, or high volume sampler according to methods set forth in § 98.234(b), (c), and (d), respectively.

(3) . If you elect to conduct continuous volumetric emission measurements for an individual compressor source as specified in paragraph (p)(1)(ii) of this section, you must measure volumetric emissions as specified in paragraphs (p)(3)(i) and (p)(3)(ii) of this section.

(i) Continuously measure the volumetric flow for the individual compressor sources at standard conditions using a permanent meter according to methods set forth in § 98.234(b).

(ii) If compressor blowdown emissions are included in the metered emissions specified in paragraph (p)(3)(i) of this section, the compressor blowdown emissions may be included with the reported emissions for the compressor source and do not need to be calculated separately using the method specified in paragraph (i) of this section for blowdown vent stacks.

(4) . If conducting measurements for a manifolded group of compressor sources, you must measure volumetric emissions as specified in paragraphs (p)(4)(i) and (ii) of this section.

(i) Measure at a single point in the manifold downstream of all compressor inputs and, if practical, prior to comingling with other non-compressor emission sources.

(ii) Determine the volumetric flow at standard conditions from the common stack using one of the methods specified in paragraphs (p)(4)(ii)(A) through (F) of this section.

(A) A temporary meter such as a vane anemometer according to methods set forth in § 98.234(b).

(B) Calibrated bagging according to methods set forth in § 98.234(c).

(C) A high volume sampler according to methods set forth in § 98.234(d).

(D) [Reserved]

(E) You may choose to use any of the methods set forth in § 98.234(a)(1) through (3) to screen for emissions. If emissions are detected using one of these specified methods, then you must use one of the methods specified in paragraphs (p)(4)(ii)(A) through (D) of this section. If emissions are not detected using the methods in § 98.234(a)(1) through (3), then you may assume that the volumetric emissions are zero. For the purposes of this paragraph, when using any of the methods in § 98.234(a), emissions are detected whenever a leak is detected according to the method. Acoustic leak detection is only applicable for through-valve leakage and is not applicable for screening a manifolded group of compressor sources.

(F) If one of the screening methods specified in § 98.234(a)(1) through (3) identifies a leak in a manifolded group of reciprocating compressor sources, you may use acoustic leak detection, according to § 98.234(a)(5), to identify the source of the leak. You must use one of the methods specified in paragraphs (p)(4)(ii)(A) through (D) of this section to quantify the emissions from the identified source.

(5) . If you elect to conduct continuous volumetric emission measurements for a manifolded group of compressor sources as specified in paragraph (p)(1)(iv) of this section, you must measure volumetric emissions as specified in paragraphs (p)(5)(i) through (iii) of this section.

(i) Measure at a single point in the manifold downstream of all compressor inputs and, if practical, prior to comingling with other non-compressor emission sources.

(ii) Continuously measure the volumetric flow for the manifolded group of compressor sources at standard conditions using a permanent meter according to methods set forth in § 98.234(b).

(iii) If compressor blowdown emissions are included in the metered emissions specified in paragraph (p)(5)(ii) of this section, the compressor blowdown emissions may be included with the reported emissions for the manifolded group of compressor sources and do not need to be calculated separately using the method specified in paragraph (i) of this section for blowdown vent stacks.

(6) . For compressor sources measured according to paragraph (p)(1)(i) of this section, you must calculate GHG emissions from the compressor sources as specified in paragraphs (p)(6)(i) through (iv) of this section.

(i) Using equation W-26 to this section, calculate the annual volumetric GHG emissions for each reciprocating compressor mode-source combination specified in paragraphs (p)(1)(i)(A) through (C) of this section that was measured during the reporting year.

(ii) Using equation W-27 to this section, calculate the annual volumetric GHG emissions from each reciprocating compressor mode-source combination specified in paragraphs (p)(1)(i)(A) through (C) of this section that was not measured during the reporting year.

(iii) Using equation W-28 to this section, develop an emission factor for each compressor mode-source combination specified in paragraphs (p)(1)(i)(A) through (C) of this section. These emission factors must be calculated annually and used in equation W-27 to this section to determine volumetric emissions from a reciprocating compressor in the mode-source combinations that were not measured in the reporting year.

(iv) The reporter emission factor in equation W-28 to this section may be calculated by using all measurements from a single owner or operator instead of only using measurements from a single facility. If you elect to use this option, the reporter emission factor must be applied to all reporting facilities for the owner or operator.

(7) . For compressor sources measured according to paragraph (p)(1)(ii) of this section, you must use the continuous volumetric emission measurements taken as specified in paragraph (p)(3) of this section and calculate annual volumetric GHG emissions associated with the compressor source using equation W-29A to this section.

(8) For manifolded groups of compressor sources measured according to paragraph (p)(1)(iii) of this section, you must calculate annual GHG emissions using equation W-29B to this section. If the reciprocating compressors included in the manifolded group of compressor sources share the manifold with centrifugal compressors, you must follow the procedures in either this paragraph (p)(8) or paragraph (o)(8) of this section to calculate emissions from the manifolded group of compressor sources.

(9) . For a manifolded group of compressor sources measured according to paragraph (p)(1)(iv) of this section, you must use the continuous volumetric emission measurements taken as specified in paragraph (p)(5) of this section and calculate annual volumetric GHG emissions associated with each manifolded group of compressor sources using equation W-29C to this section. If the reciprocating compressors included in the manifolded group of compressor sources share the manifold with centrifugal compressors, you must follow the procedures in either this paragraph (p)(9) or paragraph (o)(9) of this section to calculate emissions from the manifolded group of compressor sources.

(10) . You must calculate volumetric emissions from reciprocating compressors at an onshore petroleum and natural gas production facility or an onshore petroleum and natural gas gathering and boosting facility as specified in paragraphs (p)(10)(i) through (iv) of this section, as applicable.

(i) For all reciprocating compressors at an onshore petroleum and natural gas production facility or an onshore petroleum and natural gas gathering and boosting facility that are subject to the reciprocating compressor standards in § 60.5385b of this chapter or an applicable approved state plan or applicable Federal plan in part 62 of this chapter, you must conduct the volumetric emission measurements as required by § 60.5385b(b) and (c) of this chapter or an applicable approved state plan or applicable Federal plan in part 62 of this chapter, conduct any additional volumetric emission measurements specified in paragraph (p)(1) of this section using methods specified in paragraphs (p)(2) through (5) of this section (based on the compressor mode (as defined in § 98.238) in which the compressor was found at the time of measurement), and calculate emissions as specified in paragraphs (p)(6) through (9) of this section. Conduct all measurements required by this paragraph (p)(10)(i) at the frequency specified by § 60.5385b(a) of this chapter or an applicable approved state plan or applicable Federal plan in part 62 of this chapter. For any reporting year in which measuring at the frequency specified by § 60.5385b(a) of this chapter results in measurement not being required for a subject compressor, calculate emissions for all mode-source combinations as specified in paragraph (p)(6)(ii) of this section.

(ii) For all reciprocating compressors at an onshore petroleum and natural gas production facility or an onshore petroleum and natural gas gathering and boosting facility that are not subject to the reciprocating compressor standards in § 60.5385b of this chapter or an applicable approved state plan or applicable Federal plan in part 62 of this chapter, you may elect to conduct volumetric emission measurements specified in paragraph (p)(1) of this section using methods specified in paragraphs (p)(2) through (5) of this section (based on the compressor mode (as defined in § 98.238) in which the compressor was found at the time of measurement), and calculate emissions as specified in paragraphs (p)(6) through (9) of this section.

(iii) For all reciprocating compressors at an onshore petroleum and natural gas production facility or an onshore petroleum and natural gas gathering and boosting facility for which paragraph (p)(10)(i) of this section does not apply, and you do not elect to conduct volumetric emission measurements specified in paragraph (p)(1) of this section, you must calculate total atmospheric rod packing emissions from all reciprocating compressors at either an onshore petroleum and natural gas production facility or an onshore petroleum and natural gas gathering and boosting facility using equation W-29D to this section. Reciprocating compressor rod packing emissions that are routed to a flare, combustion, or vapor recovery system are not required to be determined under this paragraph (p).

(iv) For all reciprocating compressors at an onshore petroleum and natural gas production facility or an onshore petroleum and natural gas gathering and boosting facility for which paragraph (p)(10)(i) of this section does not apply, you must calculate rod packing vent emissions from each reciprocating compressor using equation W-29E to this section. Reciprocating compressor rod packing emissions that are routed to a flare, combustion, or vapor recovery system are not required to be determined under this paragraph (p).

(11) You must calculate both CH4 and CO2 mass emissions from volumetric emissions using calculations in paragraph (v) of this section.

(o) If you are required to report emissions from centrifugal compressor venting as specified in § 98.232(d)(2), (e)(2), (f)(2), (g)(2), and (h)(2), you must conduct volumetric emission measurements specified in paragraph (o)(1) of this section using methods specified in paragraphs (o)(2) through (5) of this section; perform calculations specified in paragraphs (o)(6) through (9) of this section; and calculate CH4 and CO2 mass emissions as specified in paragraph (o)(11) of this section. If you are required to report emissions from centrifugal compressor venting at an onshore petroleum and natural gas production facility as specified in § 98.232(c)(19) or an onshore petroleum and natural gas gathering and boosting facility as specified in § 98.232(j)(8), you must calculate volumetric emissions as specified in paragraph (o)(10) of this section and calculate CH4 and CO2 mass emissions as specified in paragraph (o)(11) of this section. If emissions from a compressor source are routed to a flare, paragraphs (o)(1) through (11) of this section do not apply and instead you must calculate CH4, CO2, and N2O emissions as specified in paragraph (n) of this section and report emissions from the flare as specified in § 98.236(n). If emissions from a compressor source are routed to combustion, paragraphs (o)(1) through (11) of this section do not apply and instead you must calculate and report emissions as specified in subpart C of this part or paragraph (z) of this section, as applicable. If emissions from a compressor source are routed to a vapor recovery system, paragraphs (o)(1) through (11) of this section do not apply.

(1) You must conduct volumetric emission measurements on each centrifugal compressor as specified in this paragraph. Compressor sources (as defined in § 98.238) without manifolded vents must use a measurement method specified in paragraph (o)(1)(i) or (ii) of this section. Manifolded compressor sources (as defined in § 98.238) must use a measurement method specified in paragraph (o)(1)(i), (ii), (iii), or (iv) of this section.

(i) Measure venting from each compressor according to either paragraph (o)(1)(i)(A), (B), or (C) of this section at least once annually, based on the compressor mode (as defined in § 98.238) in which the compressor was found at the time of measurement, except as specified in paragraph (o)(1)(i)(D) of this section. If additional measurements beyond the required annual testing are performed (including duplicate measurements or measurement of additional operating modes), then all measurements satisfying the applicable monitoring and QA/QC that is required by this paragraph (o) must be used in the calculations specified in this section.

(A) For a compressor measured in operating-mode, you must measure volumetric emissions from blowdown valve leakage through the blowdown vent as specified in paragraph (o)(2)(i) of this section, measure volumetric emissions from wet seal oil degassing vents as specified in paragraph (o)(2)(ii) of this section if the compressor has wet seal oil degassing vents, and measure volumetric emissions from dry seal vents as specified in paragraph (o)(2)(iii) of this section if the compressor has dry seals.

(B) For a compressor measured in not-operating-depressurized-mode, you must measure volumetric emissions from isolation valve leakage as specified in paragraph (o)(2)(i) of this section. If a compressor is not operated and has blind flanges in place throughout the reporting period, measurement is not required in this compressor mode.

(C) For a compressor measured in standby-pressurized-mode, you must measure volumetric emissions from blowdown valve leakage through the blowdown vent as specified in paragraph (o)(2)(i) of this section, measure volumetric emissions from wet seal oil degassing vents as specified in paragraph (o)(2)(ii) of this section if the compressor has wet seal oil degassing vents, and measure volumetric emissions from dry seal vents as specified in paragraph (o)(2)(iii) of this section if the compressor has dry seals.

(D) An annual as found measurement is not required in the first year of operation for any new compressor that begins operation after as found measurements have been conducted for all existing compressors. For only the first year of operation of new compressors, calculate emissions according to paragraph (o)(6)(ii) of this section.

(ii) Instead of measuring the compressor source according to paragraph (o)(1)(i) of this section for a given compressor, you may elect to continuously measure volumetric emissions from a compressor source as specified in paragraph (o)(3) of this section.

(iii) For a compressor source that is part of a manifolded group of compressor sources (as defined in § 98.238), instead of measuring the compressor source according to paragraph (o)(1)(i), (ii), or (iv) of this section, you may elect to measure combined volumetric emissions from the manifolded group of compressor sources by conducting measurements at the common vent stack as specified in paragraph (o)(4) of this section. The measurements must be conducted at the frequency specified in paragraphs (o)(1)(iii)(A) and (B) of this section.

(A) A minimum of one measurement must be taken for each manifolded group of compressor sources in a calendar year.

(B) The measurement may be performed while the compressors are in any compressor mode.

(iv) For a compressor source that is part of a manifolded group of compressor sources, instead of measuring the compressor source according to paragraph (o)(1)(i), (ii), or (iii) of this section, you may elect to continuously measure combined volumetric emissions from the manifolded group of compressor sources as specified in paragraph (o)(5) of this section.

(2) . If conducting measurements for each compressor source, you must determine the volumetric emissions from blowdown valves and isolation valves as specified in paragraph (o)(2)(i) of this section, the volumetric emissions from wet seal oil degassing vents as specified in paragraph (o)(2)(ii) of this section, and the volumetric emissions from dry seal vents as specified in paragraph (o)(2)(iii) of this section.

(i) For blowdown valves on compressors in operating-mode or in standby-pressurized-mode and for isolation valves on compressors in not-operating-depressurized-mode, determine the volumetric emissions using one of the methods specified in paragraphs (o)(2)(i)(A) through (D) of this section.

(A) Determine the volumetric flow at standard conditions from the blowdown vent using calibrated bagging or high volume sampler according to methods set forth in § 98.234(c) and § 98.234(d), respectively.

(B) Determine the volumetric flow at standard conditions from the blowdown vent using a temporary meter such as a vane anemometer according to methods set forth in § 98.234(b).

(C) Use an acoustic leak detection device according to methods set forth in § 98.234(a)(5).

(D) You may choose to use any of the methods set forth in § 98.234(a) to screen for emissions. If emissions are detected using the methods set forth in § 98.234(a), then you must use one of the methods specified in paragraph (o)(2)(i)(A) through (C) of this section. If emissions are not detected using the methods in § 98.234(a), then you may assume that the volumetric emissions are zero. For the purposes of this paragraph, when using any of the methods in § 98.234(a), emissions are detected whenever a leak is detected according to the methods.

(ii) For wet seal oil degassing vents in operating-mode or in standby-pressurized-mode, determine volumetric flow at standard conditions, using one of the methods specified in paragraphs (o)(2)(ii)(A) through (C) of this section. You must quantitatively measure the volumetric flow for wet seal oil degassing vent; you may not use screening methods set forth in § 98.234(a) to screen for emissions for the wet seal oil degassing vent.

(A) Use a temporary meter such as a vane anemometer or permanent flow meter according to methods set forth in § 98.234(b).

(B) Use calibrated bags according to methods set forth in § 98.234(c).

(C) Use a high volume sampler according to methods set forth in § 98.234(d).

(iii) For dry seal vents in operating-mode or in standby-pressurized-mode, determine volumetric flow at standard conditions from each dry seal vent using one of the methods specified in paragraphs (o)(2)(iii)(A) through (D) of this section. The measurement should be conducted on the compressor side dry seal. If a compressor has more than one dry seal vent, determine the aggregate dry seal vent volumetric flow for the compressor as the sum of the volumetric flows determined for each dry seal vent on the compressor.

(A) Use a temporary meter such as a vane anemometer or permanent flow meter according to methods set forth in § 98.234(b).

(B) Use calibrated bags according to methods set forth in § 98.234(c).

(C) Use a high volume sampler according to methods set forth in § 98.234(d).

(D) You may choose to use any of the methods set forth in § 98.234(a)(1) through (3) to screen for emissions. If emissions are detected using one of these specified methods, then you must use one of the methods specified in paragraph (o)(2)(iii)(A) through (C) of this section. If emissions are not detected using the methods in § 98.234(a)(1) through (3), then you may assume that the volumetric emissions are zero. For the purposes of this paragraph, when using any of the methods in § 98.234(a), emissions are detected whenever a leak is detected according to the methods. Acoustic leak detection is only applicable for through-valve leakage and is not applicable for screening dry seal vents.

(3) If you elect to conduct continuous volumetric emission measurements for an individual compressor source as specified in paragraph (o)(1)(ii) of this section, you must measure volumetric emissions as specified in paragraphs (o)(3)(i) and (ii) of this section.

(i) Continuously measure the volumetric flow for the individual compressor source at standard conditions using a permanent meter according to methods set forth in § 98.234(b).

(ii) If compressor blowdown emissions are included in the metered emissions specified in paragraph (o)(3)(i) of this section, the compressor blowdown emissions may be included with the reported emissions for the compressor source and do not need to be calculated separately using the method specified in paragraph (i) of this section for blowdown vent stacks.

(4) If conducting measurements for a manifolded group of compressor sources, you must measure volumetric emissions as specified in paragraphs (o)(4)(i) and (ii) of this section.

(i) Measure at a single point in the manifold downstream of all compressor inputs and, if practical, prior to comingling with other non-compressor emission sources.

(ii) Determine the volumetric flow at standard conditions from the common stack using one of the methods specified in paragraphs (o)(4)(ii)(A) through (F) of this section.

(A) A temporary meter such as a vane anemometer according the methods set forth in § 98.234(b).

(B) Calibrated bagging according to methods set forth in § 98.234(c).

(C) A high volume sampler according to methods set forth § 98.234(d).

(D) [Reserved]

(E) You may choose to use any of the methods set forth in § 98.234(a)(1) through (3) to screen for emissions. If emissions are detected using one of these methods, then you must use one of the methods specified in paragraph (o)(4)(ii)(A) through (D) of this section. If emissions are not detected using the methods in § 98.234(a)(1) through (3), then you may assume that the volumetric emissions are zero. For the purposes of this paragraph, when using any of the methods in § 98.234(a), emissions are detected whenever a leak is detected according to the method. Acoustic leak detection is only applicable for through-valve leakage and is not applicable for screening a manifolded group of compressor sources.

(F) If one of the screening methods specified in § 98.234(a)(1) through (3) identifies a leak in a manifolded group of centrifugal compressor sources, you may use acoustic leak detection, according to § 98.234(a)(5), to identify the source of the leak. You must use one of the methods specified in paragraphs (o)(4)(ii)(A) through (D) of this section to quantify emissions from the identified source.

(5) If you elect to conduct continuous volumetric emission measurements for a manifolded group of compressor sources as specified in paragraph (o)(1)(iv) of this section, you must measure volumetric emissions as specified in paragraphs (o)(5)(i) through (iii) of this section.

(i) Measure at a single point in the manifold downstream of all compressor inputs and, if practical, prior to comingling with other non-compressor emission sources.

(ii) Continuously measure the volumetric flow for the manifolded group of compressor sources at standard conditions using a permanent meter according to methods set forth in § 98.234(b).

(iii) If compressor blowdown emissions are included in the metered emissions specified in paragraph (o)(5)(ii) of this section, the compressor blowdown emissions may be included with the reported emissions for the manifolded group of compressor sources and do not need to be calculated separately using the method specified in paragraph (i) of this section for blowdown vent stacks.

(6) . For compressor sources measured according to paragraph (o)(1)(i) of this section, you must calculate annual GHG emissions from the compressor sources as specified in paragraphs (o)(6)(i) through (iv) of this section.

(i) Using equation W-21 to this section, calculate the annual volumetric GHG emissions for each centrifugal compressor mode-source combination specified in paragraphs (o)(1)(i)(A) through (C) of this section that was measured during the reporting year.

(ii) Using equation W-22 to this section, calculate the annual volumetric GHG emissions from each centrifugal compressor mode-source combination specified in paragraphs (o)(1)(i)(A) through (C) of this section that was not measured during the reporting year.

(iii) Using equation W-23 to this section, develop an emission factor for each compressor mode-source combination specified in paragraphs (o)(1)(i)(A) through (C) of this section. These emission factors must be calculated annually and used in equation W-22 to this section to determine volumetric emissions from a centrifugal compressor in the mode- source combinations that were not measured in the reporting year.

(iv) The reporter emission factor in equation W-23 to this section may be calculated by using all measurements from a single owner or operator instead of only using measurements from a single facility. If you elect to use this option, the reporter emission factor must be applied to all reporting facilities for the owner or operator.

(7) . For compressor sources measured according to paragraph (o)(1)(ii) of this section, you must use the continuous volumetric emission measurements taken as specified in paragraph (o)(3) of this section and calculate annual volumetric GHG emissions associated with the compressor source using equation W-24A to this section.

(8) . For manifolded groups of compressor sources measured according to paragraph (o)(1)(iii) of this section, you must calculate annual volumetric GHG emissions using equation W-24B to this section. If the centrifugal compressors included in the manifolded group of compressor sources share the manifold with reciprocating compressors, you must follow the procedures in either this paragraph (o)(8) or paragraph (p)(8) of this section to calculate emissions from the manifolded group of compressor sources.

(9) For a manifolded group of compressor sources measured according to paragraph (o)(1)(iv) of this section, you must use the continuous volumetric emission measurements taken as specified in paragraph (o)(5) of this section and calculate annual volumetric GHG emissions associated with each manifolded group of compressor sources using equation W-24C to this section. If the centrifugal compressors included in the manifolded group of compressor sources share the manifold with reciprocating compressors, you must follow the procedures in either this paragraph (o)(9) or paragraph (p)(9) of this section to calculate emissions from the manifolded group of compressor sources.

(10) You must calculate volumetric emissions from centrifugal compressors at an onshore petroleum and natural gas production facility or an onshore petroleum and natural gas gathering and boosting facility as specified in paragraphs (o)(10)(i) through (iv), as applicable.

(i) For all centrifugal compressors at an onshore petroleum and natural gas production facility or an onshore petroleum and natural gas gathering and boosting facility that are subject to the centrifugal compressor standards in § 60.5380b of this chapter or an applicable approved state plan or applicable Federal plan in part 62 of this chapter for dry seals and self-contained wet seals, you must conduct the volumetric emission measurements as required by § 60.5380b(a)(5) of this chapter or an applicable approved state plan or applicable Federal plan in part 62 of this chapter, conduct all additional volumetric emission measurements specified in paragraph (o)(1) of this section using methods specified in paragraphs (o)(2) through (5) of this section (based on the compressor mode (as defined in § 98.238) in which the compressor was found at the time of measurement), and calculate emissions as specified in paragraphs (o)(6) through (9) of this section. Conduct all measurements required by this paragraph (o)(10)(i) at the frequency specified by § 60.5380b(a)(4) of this chapter or an applicable approved state plan or applicable Federal plan in part 62 of this chapter. For any reporting year in which measuring at the frequency specified by § 60.5380b(a)(4) of this chapter results in measurement not being required for a subject compressor, calculate emissions for all mode-source combinations as specified in paragraph (o)(6)(ii) of this section.

(ii) For all centrifugal compressors at an onshore petroleum and natural gas production facility or an onshore petroleum and natural gas gathering and boosting facility that are not subject to the centrifugal compressor standards in § 60.5380b of this chapter or an applicable approved state plan or applicable Federal plan in part 62 of this chapter for dry seals and self-contained wet seals, you may elect to conduct the volumetric emission measurements specified in paragraph (o)(1) of this section using methods specified in paragraphs (o)(2) through (5) of this section (based on the compressor mode (as defined in § 98.238) in which the compressor was found at the time of measurement), and calculate emissions as specified in paragraphs (o)(6) through (9) of this section.

(iii) For all centrifugal compressors at an onshore petroleum and natural gas production facility or an onshore petroleum and natural gas gathering and boosting facility for which paragraph (o)(10)(i) of this section does not apply and you do not elect to conduct the volumetric measurements specified in paragraph (o)(1) of this section, you must calculate total atmospheric wet seal oil degassing vent emissions from all centrifugal compressors at either an onshore petroleum and natural gas production facility or an onshore petroleum and natural gas gathering and boosting facility using equation W-25A to this section. Emissions from centrifugal compressor wet seal oil degassing vents that are routed to a flare, combustion, or vapor recovery system are not required to be determined under this paragraph (o).

(iv) For all centrifugal compressors at an onshore petroleum and natural gas production facility or an onshore petroleum and natural gas gathering and boosting facility for which paragraph (o)(10)(i) of this section does not apply, and you do not elect to conduct the volumetric measurements specified in paragraph (o)(1) of this section, you must calculate wet seal oil degassing vent emissions from each centrifugal compressor using equation W-25B to this section. Emissions from centrifugal compressor wet seal oil degassing vents that are routed to a flare, combustion, or vapor recovery system are not required to be determined under this paragraph (o).

(11) . You must calculate both CH4 and CO2 mass emissions from volumetric emissions using calculations in paragraph (v) of this section.

(i) For the components listed in § 98.232(e)(7), (f)(5), (g)(4), and (h)(5), that are not subject to the well site or compressor station fugitive emissions standards in § 60.5397a of this chapter, the fugitive emissions standards for well sites, centralized production facilities, and compressor stations in § 60.5397b or 60.5398b of this chapter, or an applicable approved state plan or applicable Federal plan in part 62 of this chapter, you must conduct surveys using any of the leak detection methods listed in § 98.234(a) and calculate equipment leak emissions using the procedures specified in either paragraph (q)(2) or (3) of this section.

(2) You must indicate whether your facility contains any of the component types subject to or complying with § 98.233(q) that are listed in § 98.232(c)(21), (d)(7), (e)(7) or (8), (f)(5) through (8), (g)(4), (g)(6) or (7), (h)(5), (h)(7) or (8), (i)(1), (j)(10), (m)(3)(ii) or (m)(4)(ii) for your facility's industry segment. For each component type and leak detection method combination that is located at your well-pad site, gathering and boosting site, or facility, you must report the information specified in paragraphs (q)(2)(i) through (ix) of this section. If a component type is located at your well-pad site, gathering and boosting site, or facility and no leaks were identified from that component, then you must report the information in paragraphs (q)(2)(i) through (ix) of this section but report a zero (“0”) for the information required according to paragraphs (q)(2)(vi) through (ix) of this section. If you used Calculation Method 1 (leaker factor emission calculation methodology) for some complete leak surveys and used Calculation Method 2 (leaker measurement methodology) for some complete leak surveys, you must report the information specified in paragraphs (q)(2)(i) through (ix) of this section separately for component surveys using Calculation Method 1 and Calculation Method 2.

(i) Well-pad ID (for the onshore petroleum and natural gas production industry segment only) or gathering and boosting site ID (for the onshore petroleum and natural gas gathering and boosting industry segment only).

(iii) Leak detection method used for the screening survey (e.g., Method 21 as specified in § 98.234(a)(2)(i); Method 21 as specified in § 98.234(a)(2)(ii); and OGI and other leak detection methods as specified in § 98.234(a)(1), (3), or (5)).

(iv) Emission factor or measurement method used (e.g., default emission factor; facility-specific emission factor developed according to § 98.233(q)(4); or direct measurement according to § 98.233(q)(3)).

(vi) Total number of the surveyed component types by leak detection method that were identified as leaking in the calendar year (“xp” in equation W-30 to § 98.233 for the component type or the number of leaks measured for the specified component type according to the provisions in § 98.233(q)(3)).

(vii) Average time the surveyed components are assumed to be leaking and operational, in hours (average of “Tp,z” from equation W-30 to § 98.233 for the component type or average duration of leaks for the specified component type determined according to the provisions in § 98.233(q)(3)(ii)).

(viii) Annual CO2 emissions, in metric tons CO2, for the component type as calculated using equation W-30 to § 98.233 or § 98.233(q)(3)(vii) (for surveyed components only).

(ix) Annual CH4 emissions, in metric tons CH4, for the component type as calculated using equation W-30 to § 98.233 or § 98.233(q)(3)(vii) (for surveyed components only).

(2) You must indicate whether your facility contains any of the component types subject to or complying with § 98.233(q) that are listed in § 98.232(c)(21), (d)(7), (e)(7) or (8), (f)(5) through (8), (g)(4), (g)(6) or (7), (h)(5), (h)(7) or (8), (i)(1), (j)(10), (m)(3)(ii) or (m)(4)(ii) for your facility's industry segment. For each component type and leak detection method combination that is located at your well-pad site, gathering and boosting site, or facility, you must report the information specified in paragraphs (q)(2)(i) through (ix) of this section. If a component type is located at your well-pad site, gathering and boosting site, or facility and no leaks were identified from that component, then you must report the information in paragraphs (q)(2)(i) through (ix) of this section but report a zero (“0”) for the information required according to paragraphs (q)(2)(vi) through (ix) of this section. If you used Calculation Method 1 (leaker factor emission calculation methodology) for some complete leak surveys and used Calculation Method 2 (leaker measurement methodology) for some complete leak surveys, you must report the information specified in paragraphs (q)(2)(i) through (ix) of this section separately for component surveys using Calculation Method 1 and Calculation Method 2.

(i) Well-pad ID (for the onshore petroleum and natural gas production industry segment only) or gathering and boosting site ID (for the onshore petroleum and natural gas gathering and boosting industry segment only).

(iii) Leak detection method used for the screening survey (e.g., Method 21 as specified in § 98.234(a)(2)(i); Method 21 as specified in § 98.234(a)(2)(ii); and OGI and other leak detection methods as specified in § 98.234(a)(1), (3), or (5)).

(iv) Emission factor or measurement method used (e.g., default emission factor; facility-specific emission factor developed according to § 98.233(q)(4); or direct measurement according to § 98.233(q)(3)).

(vi) Total number of the surveyed component types by leak detection method that were identified as leaking in the calendar year (“xp” in equation W-30 to § 98.233 for the component type or the number of leaks measured for the specified component type according to the provisions in § 98.233(q)(3)).

(vii) Average time the surveyed components are assumed to be leaking and operational, in hours (average of “Tp,z” from equation W-30 to § 98.233 for the component type or average duration of leaks for the specified component type determined according to the provisions in § 98.233(q)(3)(ii)).

(viii) Annual CO2 emissions, in metric tons CO2, for the component type as calculated using equation W-30 to § 98.233 or § 98.233(q)(3)(vii) (for surveyed components only).

(ix) Annual CH4 emissions, in metric tons CH4, for the component type as calculated using equation W-30 to § 98.233 or § 98.233(q)(3)(vii) (for surveyed components only).

(B) If you elect to use a leak detection method in § 98.234(a) for the surveyed component types in § 98.232(e)(8), (f)(6) and (8), (g)(7), and (h)(8), then you must use the procedures in either paragraph (q)(2) or (3) of this section to calculate those emissions.

(2) You must indicate whether your facility contains any of the component types subject to or complying with § 98.233(q) that are listed in § 98.232(c)(21), (d)(7), (e)(7) or (8), (f)(5) through (8), (g)(4), (g)(6) or (7), (h)(5), (h)(7) or (8), (i)(1), (j)(10), (m)(3)(ii) or (m)(4)(ii) for your facility's industry segment. For each component type and leak detection method combination that is located at your well-pad site, gathering and boosting site, or facility, you must report the information specified in paragraphs (q)(2)(i) through (ix) of this section. If a component type is located at your well-pad site, gathering and boosting site, or facility and no leaks were identified from that component, then you must report the information in paragraphs (q)(2)(i) through (ix) of this section but report a zero (“0”) for the information required according to paragraphs (q)(2)(vi) through (ix) of this section. If you used Calculation Method 1 (leaker factor emission calculation methodology) for some complete leak surveys and used Calculation Method 2 (leaker measurement methodology) for some complete leak surveys, you must report the information specified in paragraphs (q)(2)(i) through (ix) of this section separately for component surveys using Calculation Method 1 and Calculation Method 2.

(i) Well-pad ID (for the onshore petroleum and natural gas production industry segment only) or gathering and boosting site ID (for the onshore petroleum and natural gas gathering and boosting industry segment only).

(iii) Leak detection method used for the screening survey (e.g., Method 21 as specified in § 98.234(a)(2)(i); Method 21 as specified in § 98.234(a)(2)(ii); and OGI and other leak detection methods as specified in § 98.234(a)(1), (3), or (5)).

(iv) Emission factor or measurement method used (e.g., default emission factor; facility-specific emission factor developed according to § 98.233(q)(4); or direct measurement according to § 98.233(q)(3)).

(vi) Total number of the surveyed component types by leak detection method that were identified as leaking in the calendar year (“xp” in equation W-30 to § 98.233 for the component type or the number of leaks measured for the specified component type according to the provisions in § 98.233(q)(3)).

(vii) Average time the surveyed components are assumed to be leaking and operational, in hours (average of “Tp,z” from equation W-30 to § 98.233 for the component type or average duration of leaks for the specified component type determined according to the provisions in § 98.233(q)(3)(ii)).

(viii) Annual CO2 emissions, in metric tons CO2, for the component type as calculated using equation W-30 to § 98.233 or § 98.233(q)(3)(vii) (for surveyed components only).

(ix) Annual CH4 emissions, in metric tons CH4, for the component type as calculated using equation W-30 to § 98.233 or § 98.233(q)(3)(vii) (for surveyed components only).

(a) You must report CO2, CH4, and N2O emissions from each industry segment specified in paragraphs (b) through (j) and (m) of this section, CO2, CH4, and N2O emissions from each flare as specified in paragraphs (b) through (j) of this section, and stationary and portable combustion emissions as applicable as specified in paragraph (k) of this section. You must also report the information specified in paragraph (l) of this section, as applicable.

(p) If you are required to report emissions from reciprocating compressor venting as specified in § 98.232(d)(1), (e)(1), (f)(1), (g)(1), and (h)(1), you must conduct volumetric emission measurements specified in paragraph (p)(1) of this section using methods specified in paragraphs (p)(2) through (5) of this section; perform calculations specified in paragraphs (p)(6) through (9) of this section; and calculate CH4 and CO2 mass emissions as specified in paragraph (p)(11) of this section. If you are required to report emissions from reciprocating compressor venting at an onshore petroleum and natural gas production facility as specified in § 98.232(c)(11) or an onshore petroleum and natural gas gathering and boosting facility as specified in § 98.232(j)(9), you must calculate volumetric emissions as specified in paragraph (p)(10) of this section and calculate CH4 and CO2 mass emissions as specified in paragraph (p)(11) of this section. If emissions from a compressor source are routed to a flare, paragraphs (p)(1) through (11) of this section do not apply and instead you must calculate CH4, CO2, and N2O emissions as specified in paragraph (n) of this section and report emissions from the flare as specified in § 98.236(n). If emissions from a compressor source are routed to combustion, paragraphs (p)(1) through (11) of this section do not apply and instead you must calculate and report emissions as specified in subpart C of this part or paragraph (z) of this section, as applicable. If emissions from a compressor source are routed to a vapor recovery system, paragraphs (p)(1) through (11) of this section do not apply.

(1) You must conduct volumetric emission measurements on each reciprocating compressor as specified in this paragraph. Compressor sources (as defined in § 98.238) without manifolded vents must use a measurement method specified in paragraph (p)(1)(i) or (ii) of this section. Manifolded compressor sources (as defined in § 98.238) must use a measurement method specified in paragraph (p)(1)(i), (ii), (iii), or (iv) of this section.

(i) Measure venting from each compressor according to either paragraph (p)(1)(i)(A), (B), or (C) of this section at least once annually, based on the compressor mode (as defined in § 98.238) in which the compressor was found at the time of measurement, except as specified in paragraph (p)(1)(i)(D) of this section. If additional measurements beyond the required annual testing are performed (including duplicate measurements or measurement of additional operating modes), then all measurements satisfying the applicable monitoring and QA/QC that is required by this paragraph (p) must be used in the calculations specified in this section.

(A) For a compressor measured in operating-mode, you must measure volumetric emissions from blowdown valve leakage through the blowdown vent as specified in paragraph (p)(2)(i) of this section, and measure volumetric emissions from reciprocating rod packing as specified in paragraph (p)(2)(ii) or (iii) of this section, as applicable.

(B) For a compressor measured in not-operating-depressurized-mode, you must measure volumetric emissions from isolation valve leakage as specified in paragraph (p)(2)(i) of this section. If a compressor is not operated and has blind flanges in place throughout the reporting period, measurement is not required in this compressor mode.

(C) For a compressor measured in standby-pressurized-mode, you must measure volumetric emissions from blowdown valve leakage through the blowdown vent as specified in paragraph (p)(2)(i) of this section and measure volumetric emissions from reciprocating rod packing as specified in paragraph (p)(2)(ii) or (iii) of this section, as applicable.

(D) An annual as found measurement is not required in the first year of operation for any new compressor that begins operation after as found measurements have been conducted for all existing compressors. For only the first year of operation of new compressors, calculate emissions according to paragraph (p)(6)(ii) of this section.

(ii) Instead of measuring the compressor source according to paragraph (p)(1)(i) of this section for a given compressor, you may elect to continuously measure volumetric emissions from a compressor source as specified in paragraph (p)(3) of this section.

(iii) For a compressor source that is part of a manifolded group of compressor sources (as defined in § 98.238), instead of measuring the compressor source according to paragraph (p)(1)(i), (ii), or (iv) of this section, you may elect to measure combined volumetric emissions from the manifolded group of compressor sources by conducting measurements at the common vent stack as specified in paragraph (p)(4) of this section. The measurements must be conducted at the frequency specified in paragraphs (p)(1)(iii)(A) and (B) of this section.

(A) A minimum of one measurement must be taken for each manifolded group of compressor sources in a calendar year.

(B) The measurement may be performed while the compressors are in any compressor mode.

(iv) For a compressor source that is part of a manifolded group of compressor sources, instead of measuring the compressor source according to paragraph (p)(1)(i), (ii), or (iii) of this section, you may elect to continuously measure combined volumetric emissions from the manifolded group of compressors sources as specified in paragraph (p)(5) of this section.

(2) . If conducting measurements for each compressor source, you must determine the volumetric emissions from blowdown valves and isolation valves as specified in paragraph (p)(2)(i) of this section. You must determine the volumetric emissions from reciprocating rod packing as specified in paragraph (p)(2)(ii) or (iii) of this section, as applicable.

(i) and for isolation valves on compressors in not-operating-depressurized-mode, determine the volumetric emissions using one of the methods specified in paragraphs (p)(2)(i)(A) through (D) of this section.

(A) Determine the volumetric flow at standard conditions from the blowdown vent using calibrated bagging or high volume sampler according to methods set forth in § 98.234(c) and (d), respectively.

(B) Determine the volumetric flow at standard conditions from the blowdown vent using a temporary meter such as a vane anemometer, according to methods set forth in § 98.234(b).

(C) Use an acoustic leak detection device according to methods set forth in § 98.234(a)(5).

(D) You may choose to use any of the methods set forth in § 98.234(a) to screen for emissions. If emissions are detected using the methods set forth in § 98.234(a), then you must use one of the methods specified in paragraphs (p)(2)(i)(A) through (C) of this section. If emissions are not detected using the methods in § 98.234(a), then you may assume that the volumetric emissions are zero. For the purposes of this paragraph, when using any of the methods in § 98.234(a), emissions are detected whenever a leak is detected according to the method.

(ii) For reciprocating rod packing equipped with an open-ended vent line on compressors in operating-mode or standby-pressurized-mode, determine the volumetric emissions using one of the methods specified in paragraphs (p)(2)(ii)(A) through (C) of this section.

(A) Determine the volumetric flow at standard conditions from the open-ended vent line using calibrated bagging or high volume sampler according to methods set forth in § 98.234(c) and (d), respectively.

(B) Determine the volumetric flow at standard conditions from the open-ended vent line using a temporary meter such as a vane anemometer, according to methods set forth in § 98.234(b).

(C) You may choose to use any of the methods set forth in § 98.234(a)(1) through (3) to screen for emissions. If emissions are detected using one of these specified methods, then you must use one of the methods specified in paragraphs (p)(2)(ii)(A) and (B) of this section. If emissions are not detected using the methods in § 98.234(a)(1) through (3), then you may assume that the volumetric emissions are zero. For the purposes of this paragraph (p)(2)(ii)(C), when using any of the methods in § 98.234(a), emissions are detected whenever a leak is detected according to the method. Acoustic leak detection is only applicable for through-valve leakage and is not applicable for screening or measuring rod packing emissions.

(iii) For reciprocating rod packing not equipped with an open-ended vent line on compressors in operating-mode, you must determine the volumetric emissions using the method specified in paragraphs (p)(2)(iii)(A) and (B) of this section.

(A) You must use the methods described in § 98.234(a)(1) through (3) to conduct annual leak detection of equipment leaks from the packing case into an open distance piece, or for compressors with a closed distance piece, conduct annual detection of gas emissions from the rod packing vent, distance piece vent, compressor crank case breather cap, or other vent emitting gas from the rod packing. Acoustic leak detection is only applicable for through-valve leakage and is not applicable for screening rod packing emissions.

(B) You must measure emissions found in paragraph (p)(2)(iii)(A) of this section using an appropriate meter, calibrated bag, or high volume sampler according to methods set forth in § 98.234(b), (c), and (d), respectively.

(3) . If you elect to conduct continuous volumetric emission measurements for an individual compressor source as specified in paragraph (p)(1)(ii) of this section, you must measure volumetric emissions as specified in paragraphs (p)(3)(i) and (p)(3)(ii) of this section.

(i) Continuously measure the volumetric flow for the individual compressor sources at standard conditions using a permanent meter according to methods set forth in § 98.234(b).

(ii) If compressor blowdown emissions are included in the metered emissions specified in paragraph (p)(3)(i) of this section, the compressor blowdown emissions may be included with the reported emissions for the compressor source and do not need to be calculated separately using the method specified in paragraph (i) of this section for blowdown vent stacks.

(4) . If conducting measurements for a manifolded group of compressor sources, you must measure volumetric emissions as specified in paragraphs (p)(4)(i) and (ii) of this section.

(i) Measure at a single point in the manifold downstream of all compressor inputs and, if practical, prior to comingling with other non-compressor emission sources.

(ii) Determine the volumetric flow at standard conditions from the common stack using one of the methods specified in paragraphs (p)(4)(ii)(A) through (F) of this section.

(A) A temporary meter such as a vane anemometer according to methods set forth in § 98.234(b).

(B) Calibrated bagging according to methods set forth in § 98.234(c).

(C) A high volume sampler according to methods set forth in § 98.234(d).

(D) [Reserved]

(E) You may choose to use any of the methods set forth in § 98.234(a)(1) through (3) to screen for emissions. If emissions are detected using one of these specified methods, then you must use one of the methods specified in paragraphs (p)(4)(ii)(A) through (D) of this section. If emissions are not detected using the methods in § 98.234(a)(1) through (3), then you may assume that the volumetric emissions are zero. For the purposes of this paragraph, when using any of the methods in § 98.234(a), emissions are detected whenever a leak is detected according to the method. Acoustic leak detection is only applicable for through-valve leakage and is not applicable for screening a manifolded group of compressor sources.

(F) If one of the screening methods specified in § 98.234(a)(1) through (3) identifies a leak in a manifolded group of reciprocating compressor sources, you may use acoustic leak detection, according to § 98.234(a)(5), to identify the source of the leak. You must use one of the methods specified in paragraphs (p)(4)(ii)(A) through (D) of this section to quantify the emissions from the identified source.

(5) . If you elect to conduct continuous volumetric emission measurements for a manifolded group of compressor sources as specified in paragraph (p)(1)(iv) of this section, you must measure volumetric emissions as specified in paragraphs (p)(5)(i) through (iii) of this section.

(i) Measure at a single point in the manifold downstream of all compressor inputs and, if practical, prior to comingling with other non-compressor emission sources.

(ii) Continuously measure the volumetric flow for the manifolded group of compressor sources at standard conditions using a permanent meter according to methods set forth in § 98.234(b).

(iii) If compressor blowdown emissions are included in the metered emissions specified in paragraph (p)(5)(ii) of this section, the compressor blowdown emissions may be included with the reported emissions for the manifolded group of compressor sources and do not need to be calculated separately using the method specified in paragraph (i) of this section for blowdown vent stacks.

(6) . For compressor sources measured according to paragraph (p)(1)(i) of this section, you must calculate GHG emissions from the compressor sources as specified in paragraphs (p)(6)(i) through (iv) of this section.

(i) Using equation W-26 to this section, calculate the annual volumetric GHG emissions for each reciprocating compressor mode-source combination specified in paragraphs (p)(1)(i)(A) through (C) of this section that was measured during the reporting year.

(ii) Using equation W-27 to this section, calculate the annual volumetric GHG emissions from each reciprocating compressor mode-source combination specified in paragraphs (p)(1)(i)(A) through (C) of this section that was not measured during the reporting year.

(iii) Using equation W-28 to this section, develop an emission factor for each compressor mode-source combination specified in paragraphs (p)(1)(i)(A) through (C) of this section. These emission factors must be calculated annually and used in equation W-27 to this section to determine volumetric emissions from a reciprocating compressor in the mode-source combinations that were not measured in the reporting year.

(iv) The reporter emission factor in equation W-28 to this section may be calculated by using all measurements from a single owner or operator instead of only using measurements from a single facility. If you elect to use this option, the reporter emission factor must be applied to all reporting facilities for the owner or operator.

(7) . For compressor sources measured according to paragraph (p)(1)(ii) of this section, you must use the continuous volumetric emission measurements taken as specified in paragraph (p)(3) of this section and calculate annual volumetric GHG emissions associated with the compressor source using equation W-29A to this section.

(8) For manifolded groups of compressor sources measured according to paragraph (p)(1)(iii) of this section, you must calculate annual GHG emissions using equation W-29B to this section. If the reciprocating compressors included in the manifolded group of compressor sources share the manifold with centrifugal compressors, you must follow the procedures in either this paragraph (p)(8) or paragraph (o)(8) of this section to calculate emissions from the manifolded group of compressor sources.

(9) . For a manifolded group of compressor sources measured according to paragraph (p)(1)(iv) of this section, you must use the continuous volumetric emission measurements taken as specified in paragraph (p)(5) of this section and calculate annual volumetric GHG emissions associated with each manifolded group of compressor sources using equation W-29C to this section. If the reciprocating compressors included in the manifolded group of compressor sources share the manifold with centrifugal compressors, you must follow the procedures in either this paragraph (p)(9) or paragraph (o)(9) of this section to calculate emissions from the manifolded group of compressor sources.

(10) . You must calculate volumetric emissions from reciprocating compressors at an onshore petroleum and natural gas production facility or an onshore petroleum and natural gas gathering and boosting facility as specified in paragraphs (p)(10)(i) through (iv) of this section, as applicable.

(i) For all reciprocating compressors at an onshore petroleum and natural gas production facility or an onshore petroleum and natural gas gathering and boosting facility that are subject to the reciprocating compressor standards in § 60.5385b of this chapter or an applicable approved state plan or applicable Federal plan in part 62 of this chapter, you must conduct the volumetric emission measurements as required by § 60.5385b(b) and (c) of this chapter or an applicable approved state plan or applicable Federal plan in part 62 of this chapter, conduct any additional volumetric emission measurements specified in paragraph (p)(1) of this section using methods specified in paragraphs (p)(2) through (5) of this section (based on the compressor mode (as defined in § 98.238) in which the compressor was found at the time of measurement), and calculate emissions as specified in paragraphs (p)(6) through (9) of this section. Conduct all measurements required by this paragraph (p)(10)(i) at the frequency specified by § 60.5385b(a) of this chapter or an applicable approved state plan or applicable Federal plan in part 62 of this chapter. For any reporting year in which measuring at the frequency specified by § 60.5385b(a) of this chapter results in measurement not being required for a subject compressor, calculate emissions for all mode-source combinations as specified in paragraph (p)(6)(ii) of this section.

(ii) For all reciprocating compressors at an onshore petroleum and natural gas production facility or an onshore petroleum and natural gas gathering and boosting facility that are not subject to the reciprocating compressor standards in § 60.5385b of this chapter or an applicable approved state plan or applicable Federal plan in part 62 of this chapter, you may elect to conduct volumetric emission measurements specified in paragraph (p)(1) of this section using methods specified in paragraphs (p)(2) through (5) of this section (based on the compressor mode (as defined in § 98.238) in which the compressor was found at the time of measurement), and calculate emissions as specified in paragraphs (p)(6) through (9) of this section.

(iii) For all reciprocating compressors at an onshore petroleum and natural gas production facility or an onshore petroleum and natural gas gathering and boosting facility for which paragraph (p)(10)(i) of this section does not apply, and you do not elect to conduct volumetric emission measurements specified in paragraph (p)(1) of this section, you must calculate total atmospheric rod packing emissions from all reciprocating compressors at either an onshore petroleum and natural gas production facility or an onshore petroleum and natural gas gathering and boosting facility using equation W-29D to this section. Reciprocating compressor rod packing emissions that are routed to a flare, combustion, or vapor recovery system are not required to be determined under this paragraph (p).

(iv) For all reciprocating compressors at an onshore petroleum and natural gas production facility or an onshore petroleum and natural gas gathering and boosting facility for which paragraph (p)(10)(i) of this section does not apply, you must calculate rod packing vent emissions from each reciprocating compressor using equation W-29E to this section. Reciprocating compressor rod packing emissions that are routed to a flare, combustion, or vapor recovery system are not required to be determined under this paragraph (p).

(11) You must calculate both CH4 and CO2 mass emissions from volumetric emissions using calculations in paragraph (v) of this section.

(o) If you are required to report emissions from centrifugal compressor venting as specified in § 98.232(d)(2), (e)(2), (f)(2), (g)(2), and (h)(2), you must conduct volumetric emission measurements specified in paragraph (o)(1) of this section using methods specified in paragraphs (o)(2) through (5) of this section; perform calculations specified in paragraphs (o)(6) through (9) of this section; and calculate CH4 and CO2 mass emissions as specified in paragraph (o)(11) of this section. If you are required to report emissions from centrifugal compressor venting at an onshore petroleum and natural gas production facility as specified in § 98.232(c)(19) or an onshore petroleum and natural gas gathering and boosting facility as specified in § 98.232(j)(8), you must calculate volumetric emissions as specified in paragraph (o)(10) of this section and calculate CH4 and CO2 mass emissions as specified in paragraph (o)(11) of this section. If emissions from a compressor source are routed to a flare, paragraphs (o)(1) through (11) of this section do not apply and instead you must calculate CH4, CO2, and N2O emissions as specified in paragraph (n) of this section and report emissions from the flare as specified in § 98.236(n). If emissions from a compressor source are routed to combustion, paragraphs (o)(1) through (11) of this section do not apply and instead you must calculate and report emissions as specified in subpart C of this part or paragraph (z) of this section, as applicable. If emissions from a compressor source are routed to a vapor recovery system, paragraphs (o)(1) through (11) of this section do not apply.

(1) You must conduct volumetric emission measurements on each centrifugal compressor as specified in this paragraph. Compressor sources (as defined in § 98.238) without manifolded vents must use a measurement method specified in paragraph (o)(1)(i) or (ii) of this section. Manifolded compressor sources (as defined in § 98.238) must use a measurement method specified in paragraph (o)(1)(i), (ii), (iii), or (iv) of this section.

(i) Measure venting from each compressor according to either paragraph (o)(1)(i)(A), (B), or (C) of this section at least once annually, based on the compressor mode (as defined in § 98.238) in which the compressor was found at the time of measurement, except as specified in paragraph (o)(1)(i)(D) of this section. If additional measurements beyond the required annual testing are performed (including duplicate measurements or measurement of additional operating modes), then all measurements satisfying the applicable monitoring and QA/QC that is required by this paragraph (o) must be used in the calculations specified in this section.

(A) For a compressor measured in operating-mode, you must measure volumetric emissions from blowdown valve leakage through the blowdown vent as specified in paragraph (o)(2)(i) of this section, measure volumetric emissions from wet seal oil degassing vents as specified in paragraph (o)(2)(ii) of this section if the compressor has wet seal oil degassing vents, and measure volumetric emissions from dry seal vents as specified in paragraph (o)(2)(iii) of this section if the compressor has dry seals.

(B) For a compressor measured in not-operating-depressurized-mode, you must measure volumetric emissions from isolation valve leakage as specified in paragraph (o)(2)(i) of this section. If a compressor is not operated and has blind flanges in place throughout the reporting period, measurement is not required in this compressor mode.

(C) For a compressor measured in standby-pressurized-mode, you must measure volumetric emissions from blowdown valve leakage through the blowdown vent as specified in paragraph (o)(2)(i) of this section, measure volumetric emissions from wet seal oil degassing vents as specified in paragraph (o)(2)(ii) of this section if the compressor has wet seal oil degassing vents, and measure volumetric emissions from dry seal vents as specified in paragraph (o)(2)(iii) of this section if the compressor has dry seals.

(D) An annual as found measurement is not required in the first year of operation for any new compressor that begins operation after as found measurements have been conducted for all existing compressors. For only the first year of operation of new compressors, calculate emissions according to paragraph (o)(6)(ii) of this section.

(ii) Instead of measuring the compressor source according to paragraph (o)(1)(i) of this section for a given compressor, you may elect to continuously measure volumetric emissions from a compressor source as specified in paragraph (o)(3) of this section.

(iii) For a compressor source that is part of a manifolded group of compressor sources (as defined in § 98.238), instead of measuring the compressor source according to paragraph (o)(1)(i), (ii), or (iv) of this section, you may elect to measure combined volumetric emissions from the manifolded group of compressor sources by conducting measurements at the common vent stack as specified in paragraph (o)(4) of this section. The measurements must be conducted at the frequency specified in paragraphs (o)(1)(iii)(A) and (B) of this section.

(A) A minimum of one measurement must be taken for each manifolded group of compressor sources in a calendar year.

(B) The measurement may be performed while the compressors are in any compressor mode.

(iv) For a compressor source that is part of a manifolded group of compressor sources, instead of measuring the compressor source according to paragraph (o)(1)(i), (ii), or (iii) of this section, you may elect to continuously measure combined volumetric emissions from the manifolded group of compressor sources as specified in paragraph (o)(5) of this section.

(2) . If conducting measurements for each compressor source, you must determine the volumetric emissions from blowdown valves and isolation valves as specified in paragraph (o)(2)(i) of this section, the volumetric emissions from wet seal oil degassing vents as specified in paragraph (o)(2)(ii) of this section, and the volumetric emissions from dry seal vents as specified in paragraph (o)(2)(iii) of this section.

(i) For blowdown valves on compressors in operating-mode or in standby-pressurized-mode and for isolation valves on compressors in not-operating-depressurized-mode, determine the volumetric emissions using one of the methods specified in paragraphs (o)(2)(i)(A) through (D) of this section.

(A) Determine the volumetric flow at standard conditions from the blowdown vent using calibrated bagging or high volume sampler according to methods set forth in § 98.234(c) and § 98.234(d), respectively.

(B) Determine the volumetric flow at standard conditions from the blowdown vent using a temporary meter such as a vane anemometer according to methods set forth in § 98.234(b).

(C) Use an acoustic leak detection device according to methods set forth in § 98.234(a)(5).

(D) You may choose to use any of the methods set forth in § 98.234(a) to screen for emissions. If emissions are detected using the methods set forth in § 98.234(a), then you must use one of the methods specified in paragraph (o)(2)(i)(A) through (C) of this section. If emissions are not detected using the methods in § 98.234(a), then you may assume that the volumetric emissions are zero. For the purposes of this paragraph, when using any of the methods in § 98.234(a), emissions are detected whenever a leak is detected according to the methods.

(ii) For wet seal oil degassing vents in operating-mode or in standby-pressurized-mode, determine volumetric flow at standard conditions, using one of the methods specified in paragraphs (o)(2)(ii)(A) through (C) of this section. You must quantitatively measure the volumetric flow for wet seal oil degassing vent; you may not use screening methods set forth in § 98.234(a) to screen for emissions for the wet seal oil degassing vent.

(A) Use a temporary meter such as a vane anemometer or permanent flow meter according to methods set forth in § 98.234(b).

(B) Use calibrated bags according to methods set forth in § 98.234(c).

(C) Use a high volume sampler according to methods set forth in § 98.234(d).

(iii) For dry seal vents in operating-mode or in standby-pressurized-mode, determine volumetric flow at standard conditions from each dry seal vent using one of the methods specified in paragraphs (o)(2)(iii)(A) through (D) of this section. The measurement should be conducted on the compressor side dry seal. If a compressor has more than one dry seal vent, determine the aggregate dry seal vent volumetric flow for the compressor as the sum of the volumetric flows determined for each dry seal vent on the compressor.

(A) Use a temporary meter such as a vane anemometer or permanent flow meter according to methods set forth in § 98.234(b).

(B) Use calibrated bags according to methods set forth in § 98.234(c).

(C) Use a high volume sampler according to methods set forth in § 98.234(d).

(D) You may choose to use any of the methods set forth in § 98.234(a)(1) through (3) to screen for emissions. If emissions are detected using one of these specified methods, then you must use one of the methods specified in paragraph (o)(2)(iii)(A) through (C) of this section. If emissions are not detected using the methods in § 98.234(a)(1) through (3), then you may assume that the volumetric emissions are zero. For the purposes of this paragraph, when using any of the methods in § 98.234(a), emissions are detected whenever a leak is detected according to the methods. Acoustic leak detection is only applicable for through-valve leakage and is not applicable for screening dry seal vents.

(3) If you elect to conduct continuous volumetric emission measurements for an individual compressor source as specified in paragraph (o)(1)(ii) of this section, you must measure volumetric emissions as specified in paragraphs (o)(3)(i) and (ii) of this section.

(i) Continuously measure the volumetric flow for the individual compressor source at standard conditions using a permanent meter according to methods set forth in § 98.234(b).

(ii) If compressor blowdown emissions are included in the metered emissions specified in paragraph (o)(3)(i) of this section, the compressor blowdown emissions may be included with the reported emissions for the compressor source and do not need to be calculated separately using the method specified in paragraph (i) of this section for blowdown vent stacks.

(4) If conducting measurements for a manifolded group of compressor sources, you must measure volumetric emissions as specified in paragraphs (o)(4)(i) and (ii) of this section.

(i) Measure at a single point in the manifold downstream of all compressor inputs and, if practical, prior to comingling with other non-compressor emission sources.

(ii) Determine the volumetric flow at standard conditions from the common stack using one of the methods specified in paragraphs (o)(4)(ii)(A) through (F) of this section.

(A) A temporary meter such as a vane anemometer according the methods set forth in § 98.234(b).

(B) Calibrated bagging according to methods set forth in § 98.234(c).

(C) A high volume sampler according to methods set forth § 98.234(d).

(D) [Reserved]

(E) You may choose to use any of the methods set forth in § 98.234(a)(1) through (3) to screen for emissions. If emissions are detected using one of these methods, then you must use one of the methods specified in paragraph (o)(4)(ii)(A) through (D) of this section. If emissions are not detected using the methods in § 98.234(a)(1) through (3), then you may assume that the volumetric emissions are zero. For the purposes of this paragraph, when using any of the methods in § 98.234(a), emissions are detected whenever a leak is detected according to the method. Acoustic leak detection is only applicable for through-valve leakage and is not applicable for screening a manifolded group of compressor sources.

(F) If one of the screening methods specified in § 98.234(a)(1) through (3) identifies a leak in a manifolded group of centrifugal compressor sources, you may use acoustic leak detection, according to § 98.234(a)(5), to identify the source of the leak. You must use one of the methods specified in paragraphs (o)(4)(ii)(A) through (D) of this section to quantify emissions from the identified source.

(5) If you elect to conduct continuous volumetric emission measurements for a manifolded group of compressor sources as specified in paragraph (o)(1)(iv) of this section, you must measure volumetric emissions as specified in paragraphs (o)(5)(i) through (iii) of this section.

(i) Measure at a single point in the manifold downstream of all compressor inputs and, if practical, prior to comingling with other non-compressor emission sources.

(ii) Continuously measure the volumetric flow for the manifolded group of compressor sources at standard conditions using a permanent meter according to methods set forth in § 98.234(b).

(iii) If compressor blowdown emissions are included in the metered emissions specified in paragraph (o)(5)(ii) of this section, the compressor blowdown emissions may be included with the reported emissions for the manifolded group of compressor sources and do not need to be calculated separately using the method specified in paragraph (i) of this section for blowdown vent stacks.

(6) . For compressor sources measured according to paragraph (o)(1)(i) of this section, you must calculate annual GHG emissions from the compressor sources as specified in paragraphs (o)(6)(i) through (iv) of this section.

(i) Using equation W-21 to this section, calculate the annual volumetric GHG emissions for each centrifugal compressor mode-source combination specified in paragraphs (o)(1)(i)(A) through (C) of this section that was measured during the reporting year.

(ii) Using equation W-22 to this section, calculate the annual volumetric GHG emissions from each centrifugal compressor mode-source combination specified in paragraphs (o)(1)(i)(A) through (C) of this section that was not measured during the reporting year.

(iii) Using equation W-23 to this section, develop an emission factor for each compressor mode-source combination specified in paragraphs (o)(1)(i)(A) through (C) of this section. These emission factors must be calculated annually and used in equation W-22 to this section to determine volumetric emissions from a centrifugal compressor in the mode- source combinations that were not measured in the reporting year.

(iv) The reporter emission factor in equation W-23 to this section may be calculated by using all measurements from a single owner or operator instead of only using measurements from a single facility. If you elect to use this option, the reporter emission factor must be applied to all reporting facilities for the owner or operator.

(7) . For compressor sources measured according to paragraph (o)(1)(ii) of this section, you must use the continuous volumetric emission measurements taken as specified in paragraph (o)(3) of this section and calculate annual volumetric GHG emissions associated with the compressor source using equation W-24A to this section.

(8) . For manifolded groups of compressor sources measured according to paragraph (o)(1)(iii) of this section, you must calculate annual volumetric GHG emissions using equation W-24B to this section. If the centrifugal compressors included in the manifolded group of compressor sources share the manifold with reciprocating compressors, you must follow the procedures in either this paragraph (o)(8) or paragraph (p)(8) of this section to calculate emissions from the manifolded group of compressor sources.

(9) For a manifolded group of compressor sources measured according to paragraph (o)(1)(iv) of this section, you must use the continuous volumetric emission measurements taken as specified in paragraph (o)(5) of this section and calculate annual volumetric GHG emissions associated with each manifolded group of compressor sources using equation W-24C to this section. If the centrifugal compressors included in the manifolded group of compressor sources share the manifold with reciprocating compressors, you must follow the procedures in either this paragraph (o)(9) or paragraph (p)(9) of this section to calculate emissions from the manifolded group of compressor sources.

(10) You must calculate volumetric emissions from centrifugal compressors at an onshore petroleum and natural gas production facility or an onshore petroleum and natural gas gathering and boosting facility as specified in paragraphs (o)(10)(i) through (iv), as applicable.

(i) For all centrifugal compressors at an onshore petroleum and natural gas production facility or an onshore petroleum and natural gas gathering and boosting facility that are subject to the centrifugal compressor standards in § 60.5380b of this chapter or an applicable approved state plan or applicable Federal plan in part 62 of this chapter for dry seals and self-contained wet seals, you must conduct the volumetric emission measurements as required by § 60.5380b(a)(5) of this chapter or an applicable approved state plan or applicable Federal plan in part 62 of this chapter, conduct all additional volumetric emission measurements specified in paragraph (o)(1) of this section using methods specified in paragraphs (o)(2) through (5) of this section (based on the compressor mode (as defined in § 98.238) in which the compressor was found at the time of measurement), and calculate emissions as specified in paragraphs (o)(6) through (9) of this section. Conduct all measurements required by this paragraph (o)(10)(i) at the frequency specified by § 60.5380b(a)(4) of this chapter or an applicable approved state plan or applicable Federal plan in part 62 of this chapter. For any reporting year in which measuring at the frequency specified by § 60.5380b(a)(4) of this chapter results in measurement not being required for a subject compressor, calculate emissions for all mode-source combinations as specified in paragraph (o)(6)(ii) of this section.

(ii) For all centrifugal compressors at an onshore petroleum and natural gas production facility or an onshore petroleum and natural gas gathering and boosting facility that are not subject to the centrifugal compressor standards in § 60.5380b of this chapter or an applicable approved state plan or applicable Federal plan in part 62 of this chapter for dry seals and self-contained wet seals, you may elect to conduct the volumetric emission measurements specified in paragraph (o)(1) of this section using methods specified in paragraphs (o)(2) through (5) of this section (based on the compressor mode (as defined in § 98.238) in which the compressor was found at the time of measurement), and calculate emissions as specified in paragraphs (o)(6) through (9) of this section.

(iii) For all centrifugal compressors at an onshore petroleum and natural gas production facility or an onshore petroleum and natural gas gathering and boosting facility for which paragraph (o)(10)(i) of this section does not apply and you do not elect to conduct the volumetric measurements specified in paragraph (o)(1) of this section, you must calculate total atmospheric wet seal oil degassing vent emissions from all centrifugal compressors at either an onshore petroleum and natural gas production facility or an onshore petroleum and natural gas gathering and boosting facility using equation W-25A to this section. Emissions from centrifugal compressor wet seal oil degassing vents that are routed to a flare, combustion, or vapor recovery system are not required to be determined under this paragraph (o).

(iv) For all centrifugal compressors at an onshore petroleum and natural gas production facility or an onshore petroleum and natural gas gathering and boosting facility for which paragraph (o)(10)(i) of this section does not apply, and you do not elect to conduct the volumetric measurements specified in paragraph (o)(1) of this section, you must calculate wet seal oil degassing vent emissions from each centrifugal compressor using equation W-25B to this section. Emissions from centrifugal compressor wet seal oil degassing vents that are routed to a flare, combustion, or vapor recovery system are not required to be determined under this paragraph (o).

(11) . You must calculate both CH4 and CO2 mass emissions from volumetric emissions using calculations in paragraph (v) of this section.

(i) For the components listed in § 98.232(e)(7), (f)(5), (g)(4), and (h)(5), that are not subject to the well site or compressor station fugitive emissions standards in § 60.5397a of this chapter, the fugitive emissions standards for well sites, centralized production facilities, and compressor stations in § 60.5397b or 60.5398b of this chapter, or an applicable approved state plan or applicable Federal plan in part 62 of this chapter, you must conduct surveys using any of the leak detection methods listed in § 98.234(a) and calculate equipment leak emissions using the procedures specified in either paragraph (q)(2) or (3) of this section.

(2) You must indicate whether your facility contains any of the component types subject to or complying with § 98.233(q) that are listed in § 98.232(c)(21), (d)(7), (e)(7) or (8), (f)(5) through (8), (g)(4), (g)(6) or (7), (h)(5), (h)(7) or (8), (i)(1), (j)(10), (m)(3)(ii) or (m)(4)(ii) for your facility's industry segment. For each component type and leak detection method combination that is located at your well-pad site, gathering and boosting site, or facility, you must report the information specified in paragraphs (q)(2)(i) through (ix) of this section. If a component type is located at your well-pad site, gathering and boosting site, or facility and no leaks were identified from that component, then you must report the information in paragraphs (q)(2)(i) through (ix) of this section but report a zero (“0”) for the information required according to paragraphs (q)(2)(vi) through (ix) of this section. If you used Calculation Method 1 (leaker factor emission calculation methodology) for some complete leak surveys and used Calculation Method 2 (leaker measurement methodology) for some complete leak surveys, you must report the information specified in paragraphs (q)(2)(i) through (ix) of this section separately for component surveys using Calculation Method 1 and Calculation Method 2.

(i) Well-pad ID (for the onshore petroleum and natural gas production industry segment only) or gathering and boosting site ID (for the onshore petroleum and natural gas gathering and boosting industry segment only).

(iii) Leak detection method used for the screening survey (e.g., Method 21 as specified in § 98.234(a)(2)(i); Method 21 as specified in § 98.234(a)(2)(ii); and OGI and other leak detection methods as specified in § 98.234(a)(1), (3), or (5)).

(iv) Emission factor or measurement method used (e.g., default emission factor; facility-specific emission factor developed according to § 98.233(q)(4); or direct measurement according to § 98.233(q)(3)).

(vi) Total number of the surveyed component types by leak detection method that were identified as leaking in the calendar year (“xp” in equation W-30 to § 98.233 for the component type or the number of leaks measured for the specified component type according to the provisions in § 98.233(q)(3)).

(vii) Average time the surveyed components are assumed to be leaking and operational, in hours (average of “Tp,z” from equation W-30 to § 98.233 for the component type or average duration of leaks for the specified component type determined according to the provisions in § 98.233(q)(3)(ii)).

(viii) Annual CO2 emissions, in metric tons CO2, for the component type as calculated using equation W-30 to § 98.233 or § 98.233(q)(3)(vii) (for surveyed components only).

(ix) Annual CH4 emissions, in metric tons CH4, for the component type as calculated using equation W-30 to § 98.233 or § 98.233(q)(3)(vii) (for surveyed components only).

(2) You must indicate whether your facility contains any of the component types subject to or complying with § 98.233(q) that are listed in § 98.232(c)(21), (d)(7), (e)(7) or (8), (f)(5) through (8), (g)(4), (g)(6) or (7), (h)(5), (h)(7) or (8), (i)(1), (j)(10), (m)(3)(ii) or (m)(4)(ii) for your facility's industry segment. For each component type and leak detection method combination that is located at your well-pad site, gathering and boosting site, or facility, you must report the information specified in paragraphs (q)(2)(i) through (ix) of this section. If a component type is located at your well-pad site, gathering and boosting site, or facility and no leaks were identified from that component, then you must report the information in paragraphs (q)(2)(i) through (ix) of this section but report a zero (“0”) for the information required according to paragraphs (q)(2)(vi) through (ix) of this section. If you used Calculation Method 1 (leaker factor emission calculation methodology) for some complete leak surveys and used Calculation Method 2 (leaker measurement methodology) for some complete leak surveys, you must report the information specified in paragraphs (q)(2)(i) through (ix) of this section separately for component surveys using Calculation Method 1 and Calculation Method 2.

(i) Well-pad ID (for the onshore petroleum and natural gas production industry segment only) or gathering and boosting site ID (for the onshore petroleum and natural gas gathering and boosting industry segment only).

(iii) Leak detection method used for the screening survey (e.g., Method 21 as specified in § 98.234(a)(2)(i); Method 21 as specified in § 98.234(a)(2)(ii); and OGI and other leak detection methods as specified in § 98.234(a)(1), (3), or (5)).

(iv) Emission factor or measurement method used (e.g., default emission factor; facility-specific emission factor developed according to § 98.233(q)(4); or direct measurement according to § 98.233(q)(3)).

(vi) Total number of the surveyed component types by leak detection method that were identified as leaking in the calendar year (“xp” in equation W-30 to § 98.233 for the component type or the number of leaks measured for the specified component type according to the provisions in § 98.233(q)(3)).

(vii) Average time the surveyed components are assumed to be leaking and operational, in hours (average of “Tp,z” from equation W-30 to § 98.233 for the component type or average duration of leaks for the specified component type determined according to the provisions in § 98.233(q)(3)(ii)).

(viii) Annual CO2 emissions, in metric tons CO2, for the component type as calculated using equation W-30 to § 98.233 or § 98.233(q)(3)(vii) (for surveyed components only).

(ix) Annual CH4 emissions, in metric tons CH4, for the component type as calculated using equation W-30 to § 98.233 or § 98.233(q)(3)(vii) (for surveyed components only).

(B) If you elect to use a leak detection method in § 98.234(a) for the surveyed component types in § 98.232(e)(8), (f)(6) and (8), (g)(7), and (h)(8), then you must use the procedures in either paragraph (q)(2) or (3) of this section to calculate those emissions.

(2) You must indicate whether your facility contains any of the component types subject to or complying with § 98.233(q) that are listed in § 98.232(c)(21), (d)(7), (e)(7) or (8), (f)(5) through (8), (g)(4), (g)(6) or (7), (h)(5), (h)(7) or (8), (i)(1), (j)(10), (m)(3)(ii) or (m)(4)(ii) for your facility's industry segment. For each component type and leak detection method combination that is located at your well-pad site, gathering and boosting site, or facility, you must report the information specified in paragraphs (q)(2)(i) through (ix) of this section. If a component type is located at your well-pad site, gathering and boosting site, or facility and no leaks were identified from that component, then you must report the information in paragraphs (q)(2)(i) through (ix) of this section but report a zero (“0”) for the information required according to paragraphs (q)(2)(vi) through (ix) of this section. If you used Calculation Method 1 (leaker factor emission calculation methodology) for some complete leak surveys and used Calculation Method 2 (leaker measurement methodology) for some complete leak surveys, you must report the information specified in paragraphs (q)(2)(i) through (ix) of this section separately for component surveys using Calculation Method 1 and Calculation Method 2.

(i) Well-pad ID (for the onshore petroleum and natural gas production industry segment only) or gathering and boosting site ID (for the onshore petroleum and natural gas gathering and boosting industry segment only).

(iii) Leak detection method used for the screening survey (e.g., Method 21 as specified in § 98.234(a)(2)(i); Method 21 as specified in § 98.234(a)(2)(ii); and OGI and other leak detection methods as specified in § 98.234(a)(1), (3), or (5)).

(iv) Emission factor or measurement method used (e.g., default emission factor; facility-specific emission factor developed according to § 98.233(q)(4); or direct measurement according to § 98.233(q)(3)).

(vi) Total number of the surveyed component types by leak detection method that were identified as leaking in the calendar year (“xp” in equation W-30 to § 98.233 for the component type or the number of leaks measured for the specified component type according to the provisions in § 98.233(q)(3)).

(vii) Average time the surveyed components are assumed to be leaking and operational, in hours (average of “Tp,z” from equation W-30 to § 98.233 for the component type or average duration of leaks for the specified component type determined according to the provisions in § 98.233(q)(3)(ii)).

(viii) Annual CO2 emissions, in metric tons CO2, for the component type as calculated using equation W-30 to § 98.233 or § 98.233(q)(3)(vii) (for surveyed components only).

(ix) Annual CH4 emissions, in metric tons CH4, for the component type as calculated using equation W-30 to § 98.233 or § 98.233(q)(3)(vii) (for surveyed components only).

(2) Facilities must report emissions from the natural gas distribution industry segment only if emission sources specified in § 98.232(i) emit 25,000 metric tons of CO2 equivalent or more per year.

(1) If the entire facility is acquired by an owner or operator that does not already have a reporting facility in the same industry segment and basin (for onshore petroleum and natural gas production or onshore petroleum and natural gas gathering and boosting) or state (for natural gas distribution), then within 90 days after the change in the owner or operator, the designated representative or any alternate designated representative shall submit a certificate of representation that is complete under this section. If the new owner or operator already had emission sources specified in § 98.232(c), (i), (j), or (m), as applicable, prior to the acquisition in the same basin (for onshore petroleum and natural gas production or onshore petroleum and natural gas gathering and boosting) or state (for natural gas distribution) as the acquired facility but had not previously met the applicability requirements in §§ 98.2(a) and 98.231, then per the applicable definition of facility in § 98.238, the previously owned applicable emission sources must be included in the acquired facility. The new owner or operator and the new designated representative shall be responsible for submitting the annual report for the facility for the entire reporting year beginning with the reporting year in which the acquisition occurred.

(ii) For the components listed in § 98.232(i)(1), you must conduct surveys using any of the leak detection methods listed in § 98.234(a) except § 98.234(a)(2)(ii) and calculate equipment leak emissions using the procedures specified in either paragraph (q)(2) or (3) of this section.

(q) For any components subject to or complying with the requirements of § 98.233(q), you must report the information specified in paragraphs (q)(1) and (2) of this section. You must report the information specified in paragraphs (q)(1) and (2) of this section, as applicable, for each well-pad site (for onshore production), gathering and boosting site (for onshore petroleum and natural gas gathering and boosting), or facility (for all other applicable industry segments). Natural gas distribution facilities with emission sources listed in § 98.232(i)(1) must also report the information specified in paragraph (q)(3) of this section.

(1) You must report the information specified in paragraphs (q)(1)(i) through (ix) of this section.

(i) Well-pad ID (for the onshore petroleum and natural gas production industry segment only) or gathering and boosting site ID (for the onshore petroleum and natural gas gathering and boosting industry segment only).

(ii) Except as specified in paragraph (q)(1)(iii) of this section, the number of complete equipment leak surveys performed during the calendar year.

(iii) Natural gas distribution facilities performing equipment leak surveys across a multiple year leak survey cycle must report the number of years in the leak survey cycle.

(iv) Except for natural gas distribution facilities and onshore natural gas transmission pipeline facilities, indicate whether any of the leak detection surveys used in calculating emissions per § 98.233(q)(2) were conducted for compliance with any of the standards in paragraphs (q)(1)(iv)(A) through (E) of this section. Report the indication per well-pad site, gathering and boosting site, or facility, not per component type, as applicable.

(A) The well site or compressor station fugitive emissions standards in § 60.5397a of this chapter.

(B) The well site, centralized production facility, or compressor station fugitive emissions standards in § 60.5397b or § 60.5398b of this chapter.

(C) The well site, centralized production facility, or compressor station fugitive emissions standards in an applicable approved state plan or applicable Federal plan in part 62 of this chapter.

(D) The standards for equipment leaks at onshore natural gas processing plants in § 60.5400b or § 60.5401b of this chapter.

(E) The standards for equipment leaks at onshore natural gas processing plants in an applicable approved state plan or applicable Federal plan in part 62 of this chapter.

(v) For facilities in onshore petroleum and natural gas production, onshore petroleum and natural gas gathering and boosting, onshore natural gas transmission compression, underground natural gas storage, LNG storage, and LNG import and export equipment, indicate whether you elected to comply with § 98.233(q) according to § 98.233(q)(1)(iv) for any equipment components at your well-pad site, gathering and boosting site, or facility.

(vi) Report each type of method described in § 98.234(a) that was used to conduct leak surveys.

(vii) Report whether emissions were calculated using Calculation Method 1 (leaker factor emission calculation methodology) and/or using Calculation Method 2 (leaker measurement methodology).

(viii) For facilities in onshore petroleum and natural gas production and onshore petroleum and natural gas gathering and boosting, report the number of major equipment (as listed in table W-1 to this subpart) by service type for which leak detection surveys were conducted and emissions calculated according to § 98.233(q).

(ix) For facilities in onshore petroleum and natural gas production and onshore petroleum and natural gas gathering and boosting, report the number of major equipment (as listed in table W-1 to this subpart) in vacuum service as defined in § 98.238.

(2) You must indicate whether your facility contains any of the component types subject to or complying with § 98.233(q) that are listed in § 98.232(c)(21), (d)(7), (e)(7) or (8), (f)(5) through (8), (g)(4), (g)(6) or (7), (h)(5), (h)(7) or (8), (i)(1), (j)(10), (m)(3)(ii) or (m)(4)(ii) for your facility's industry segment. For each component type and leak detection method combination that is located at your well-pad site, gathering and boosting site, or facility, you must report the information specified in paragraphs (q)(2)(i) through (ix) of this section. If a component type is located at your well-pad site, gathering and boosting site, or facility and no leaks were identified from that component, then you must report the information in paragraphs (q)(2)(i) through (ix) of this section but report a zero (“0”) for the information required according to paragraphs (q)(2)(vi) through (ix) of this section. If you used Calculation Method 1 (leaker factor emission calculation methodology) for some complete leak surveys and used Calculation Method 2 (leaker measurement methodology) for some complete leak surveys, you must report the information specified in paragraphs (q)(2)(i) through (ix) of this section separately for component surveys using Calculation Method 1 and Calculation Method 2.

(i) Well-pad ID (for the onshore petroleum and natural gas production industry segment only) or gathering and boosting site ID (for the onshore petroleum and natural gas gathering and boosting industry segment only).

(iii) Leak detection method used for the screening survey (e.g., Method 21 as specified in § 98.234(a)(2)(i); Method 21 as specified in § 98.234(a)(2)(ii); and OGI and other leak detection methods as specified in § 98.234(a)(1), (3), or (5)).

(iv) Emission factor or measurement method used (e.g., default emission factor; facility-specific emission factor developed according to § 98.233(q)(4); or direct measurement according to § 98.233(q)(3)).

(vi) Total number of the surveyed component types by leak detection method that were identified as leaking in the calendar year (“xp” in equation W-30 to § 98.233 for the component type or the number of leaks measured for the specified component type according to the provisions in § 98.233(q)(3)).

(vii) Average time the surveyed components are assumed to be leaking and operational, in hours (average of “Tp,z” from equation W-30 to § 98.233 for the component type or average duration of leaks for the specified component type determined according to the provisions in § 98.233(q)(3)(ii)).

(viii) Annual CO2 emissions, in metric tons CO2, for the component type as calculated using equation W-30 to § 98.233 or § 98.233(q)(3)(vii) (for surveyed components only).

(ix) Annual CH4 emissions, in metric tons CH4, for the component type as calculated using equation W-30 to § 98.233 or § 98.233(q)(3)(vii) (for surveyed components only).

(3) Natural gas distribution facilities with emission sources listed in § 98.232(i)(1) must also report the information specified in paragraphs (q)(3)(i) through (viii) and, if applicable, (q)(3)(ix) of this section.

(ii) Number of meter/regulator runs at above grade transmission-distribution transfer stations surveyed in the calendar year (“CountMR,y” from equation W-31 to § 98.233, for the current calendar year).

(iii) Average time that meter/regulator runs surveyed in the calendar year were operational, in hours (average of “Tw,y” from equation W-31 to § 98.233, for the current calendar year).

(iv) Number of above grade transmission-distribution transfer stations surveyed in the current leak survey cycle.

(v) Number of meter/regulator runs at above grade transmission-distribution transfer stations surveyed in current leak survey cycle (sum of “CountMR,y” from equation W-31 to § 98.233, for all calendar years in the current leak survey cycle).

(vi) Average time that meter/regulator runs surveyed in the current leak survey cycle were operational, in hours (average of “Tw,y” from equation W-31 to § 98.233, for all years included in the leak survey cycle).

(vii) Meter/regulator run CO2 emission factor based on all surveyed transmission-distribution transfer stations in the current leak survey cycle, in standard cubic feet of CO2 per operational hour of all meter/regulator runs (“EFs,MR,i” for CO2 calculated using equation W-31 to § 98.233).

(viii) Meter/regulator run CH4 emission factor based on all surveyed transmission-distribution transfer stations in the current leak survey cycle, in standard cubic feet of CH4 per operational hour of all meter/regulator runs (“EFs,MR,i” for CH4 calculated using equation W-31 to § 98.233).

(ix) If your natural gas distribution facility performs equipment leak surveys across a multiple year leak survey cycle, you must also report:

(A) The total number of meter/regulator runs at above grade transmission-distribution transfer stations at your facility (“CountMR” in equation W-32B to § 98.233).

(B) Average estimated time that each meter/regulator run at above grade transmission-distribution transfer stations was operational in the calendar year, in hours per meter/regulator run (“Tw,avg” in equation W-32B to § 98.233).

(C) Annual CO2 emissions, in metric tons CO2, for all above grade transmission-distribution transfer stations at your facility.

(D) Annual CH4 emissions, in metric tons CH4, for all above grade transmission-distribution transfer stations at your facility.

(r) This paragraph (r) applies to emissions sources listed in § 98.232(c)(21)(ii), (f)(7), (g)(5), (h)(6), (j)(10)(ii), (m)(3)(i), and (m)(4)(i) if you are not required to comply with paragraph (q) of this section and if you do not elect to comply with paragraph (q) of this section for these components in lieu of this paragraph (r). This paragraph (r) also applies to emission sources listed in § 98.232(i)(2) through (6), (j)(11), and (m)(5). To be subject to the requirements of this paragraph (r), the listed emissions sources also must contact streams with gas content greater than 10 percent CH4 plus CO2 by weight. Emissions sources that contact streams with gas content less than or equal to 10 percent CH4 plus CO2 by weight are exempt from the requirements of this paragraph (r) and do not need to be reported. Tubing systems equal to or less than one half inch diameter are exempt from the requirements of this paragraph (r) and do not need to be reported. Equipment leak components in vacuum service are exempt from the survey and emission estimation requirements of this paragraph (r) and only the count of these equipment must be reported. You must calculate emissions from all emission sources listed in this paragraph (r) using equation W-32A to this section, except for natural gas distribution facility emission sources listed in § 98.232(i)(3). Natural gas distribution facility emission sources listed in § 98.232(i)(3) must calculate emissions using equation W-32B to this section and according to paragraph (r)(6)(ii) of this section.

(1) Calculate both CH4 and CO2 mass emissions from volumetric emissions using calculations in paragraph (v) of this section.

(2) Onshore petroleum and natural gas production facilities and onshore petroleum and natural gas gathering and boosting facilities must use the appropriate default whole gas population emission factors listed in table W-1 to this subpart. Major equipment associated with gas wells are considered gas service equipment in table W-1 to this subpart. Onshore petroleum and natural gas gathering and boosting facilities shall use the gas service equipment emission factors in table W-1 to this subpart. Major equipment associated with crude oil wells are considered crude service equipment in table W-1 to this subpart. Where facilities conduct EOR operations, the emission factor listed in table W-1 to this subpart shall be used to estimate all streams of gases, including recycle CO2 stream. For meters/piping, use one meters/piping per well-pad for onshore petroleum and natural gas production operations and the number of meters in the facility for onshore petroleum and natural gas gathering and boosting operations.

(3) Underground natural gas storage facilities must use the appropriate default total hydrocarbon population emission factors for storage wellheads in gas service listed in table W-3 to this subpart.

(4) LNG storage facilities must use the appropriate default methane population emission factors for LNG storage compressors in gas service listed in table W-5 to this subpart.

(5) LNG import and export facilities must use the appropriate default methane population emission factors for LNG terminal compressors in gas service listed in table W-5 to this subpart.

(6) Natural gas distribution facilities must use the appropriate methane emission factors as described in paragraphs (r)(6)(i) and (ii) of this section.

(i) Below grade transmission-distribution transfer stations, below grade metering-regulating stations, distribution mains, and distribution services must use the appropriate default methane population emission factors listed in table W-5 to this subpart to estimate emissions from components listed in § 98.232(i)(2), (4), (5), and (6), respectively.

(ii) Above grade metering-regulating stations that are not above grade transmission-distribution transfer stations must use the meter/regulator run population emission factor calculated in equation W-31 to this section in accordance with paragraph (q)(2)(x) or (q)(3)(viii)(A) of this section for the components listed in § 98.232(i)(3). Natural gas distribution facilities that do not have above grade transmission-distribution transfer stations are not required to calculate emissions for above grade metering-regulating stations and are not required to report GHG emissions in § 98.236(r)(2)(v).

(7) Onshore natural gas transmission pipeline facilities must use the appropriate default methane population emission factors listed in table W-5 to this subpart to estimate emissions from components listed in § 98.232(m)(3)(i), (4)(i) and (5).

(r) This paragraph (r) applies to emissions sources listed in § 98.232(c)(21)(ii), (f)(7), (g)(5), (h)(6), (j)(10)(ii), (m)(3)(i), and (m)(4)(i) if you are not required to comply with paragraph (q) of this section and if you do not elect to comply with paragraph (q) of this section for these components in lieu of this paragraph (r). This paragraph (r) also applies to emission sources listed in § 98.232(i)(2) through (6), (j)(11), and (m)(5). To be subject to the requirements of this paragraph (r), the listed emissions sources also must contact streams with gas content greater than 10 percent CH4 plus CO2 by weight. Emissions sources that contact streams with gas content less than or equal to 10 percent CH4 plus CO2 by weight are exempt from the requirements of this paragraph (r) and do not need to be reported. Tubing systems equal to or less than one half inch diameter are exempt from the requirements of this paragraph (r) and do not need to be reported. Equipment leak components in vacuum service are exempt from the survey and emission estimation requirements of this paragraph (r) and only the count of these equipment must be reported. You must calculate emissions from all emission sources listed in this paragraph (r) using equation W-32A to this section, except for natural gas distribution facility emission sources listed in § 98.232(i)(3). Natural gas distribution facility emission sources listed in § 98.232(i)(3) must calculate emissions using equation W-32B to this section and according to paragraph (r)(6)(ii) of this section.

(1) Calculate both CH4 and CO2 mass emissions from volumetric emissions using calculations in paragraph (v) of this section.

(2) Onshore petroleum and natural gas production facilities and onshore petroleum and natural gas gathering and boosting facilities must use the appropriate default whole gas population emission factors listed in table W-1 to this subpart. Major equipment associated with gas wells are considered gas service equipment in table W-1 to this subpart. Onshore petroleum and natural gas gathering and boosting facilities shall use the gas service equipment emission factors in table W-1 to this subpart. Major equipment associated with crude oil wells are considered crude service equipment in table W-1 to this subpart. Where facilities conduct EOR operations, the emission factor listed in table W-1 to this subpart shall be used to estimate all streams of gases, including recycle CO2 stream. For meters/piping, use one meters/piping per well-pad for onshore petroleum and natural gas production operations and the number of meters in the facility for onshore petroleum and natural gas gathering and boosting operations.

(3) Underground natural gas storage facilities must use the appropriate default total hydrocarbon population emission factors for storage wellheads in gas service listed in table W-3 to this subpart.

(4) LNG storage facilities must use the appropriate default methane population emission factors for LNG storage compressors in gas service listed in table W-5 to this subpart.

(5) LNG import and export facilities must use the appropriate default methane population emission factors for LNG terminal compressors in gas service listed in table W-5 to this subpart.

(6) Natural gas distribution facilities must use the appropriate methane emission factors as described in paragraphs (r)(6)(i) and (ii) of this section.

(i) Below grade transmission-distribution transfer stations, below grade metering-regulating stations, distribution mains, and distribution services must use the appropriate default methane population emission factors listed in table W-5 to this subpart to estimate emissions from components listed in § 98.232(i)(2), (4), (5), and (6), respectively.

(ii) Above grade metering-regulating stations that are not above grade transmission-distribution transfer stations must use the meter/regulator run population emission factor calculated in equation W-31 to this section in accordance with paragraph (q)(2)(x) or (q)(3)(viii)(A) of this section for the components listed in § 98.232(i)(3). Natural gas distribution facilities that do not have above grade transmission-distribution transfer stations are not required to calculate emissions for above grade metering-regulating stations and are not required to report GHG emissions in § 98.236(r)(2)(v).

(7) Onshore natural gas transmission pipeline facilities must use the appropriate default methane population emission factors listed in table W-5 to this subpart to estimate emissions from components listed in § 98.232(m)(3)(i), (4)(i) and (5).

(r) This paragraph (r) applies to emissions sources listed in § 98.232(c)(21)(ii), (f)(7), (g)(5), (h)(6), (j)(10)(ii), (m)(3)(i), and (m)(4)(i) if you are not required to comply with paragraph (q) of this section and if you do not elect to comply with paragraph (q) of this section for these components in lieu of this paragraph (r). This paragraph (r) also applies to emission sources listed in § 98.232(i)(2) through (6), (j)(11), and (m)(5). To be subject to the requirements of this paragraph (r), the listed emissions sources also must contact streams with gas content greater than 10 percent CH4 plus CO2 by weight. Emissions sources that contact streams with gas content less than or equal to 10 percent CH4 plus CO2 by weight are exempt from the requirements of this paragraph (r) and do not need to be reported. Tubing systems equal to or less than one half inch diameter are exempt from the requirements of this paragraph (r) and do not need to be reported. Equipment leak components in vacuum service are exempt from the survey and emission estimation requirements of this paragraph (r) and only the count of these equipment must be reported. You must calculate emissions from all emission sources listed in this paragraph (r) using equation W-32A to this section, except for natural gas distribution facility emission sources listed in § 98.232(i)(3). Natural gas distribution facility emission sources listed in § 98.232(i)(3) must calculate emissions using equation W-32B to this section and according to paragraph (r)(6)(ii) of this section.

(1) Calculate both CH4 and CO2 mass emissions from volumetric emissions using calculations in paragraph (v) of this section.

(2) Onshore petroleum and natural gas production facilities and onshore petroleum and natural gas gathering and boosting facilities must use the appropriate default whole gas population emission factors listed in table W-1 to this subpart. Major equipment associated with gas wells are considered gas service equipment in table W-1 to this subpart. Onshore petroleum and natural gas gathering and boosting facilities shall use the gas service equipment emission factors in table W-1 to this subpart. Major equipment associated with crude oil wells are considered crude service equipment in table W-1 to this subpart. Where facilities conduct EOR operations, the emission factor listed in table W-1 to this subpart shall be used to estimate all streams of gases, including recycle CO2 stream. For meters/piping, use one meters/piping per well-pad for onshore petroleum and natural gas production operations and the number of meters in the facility for onshore petroleum and natural gas gathering and boosting operations.

(3) Underground natural gas storage facilities must use the appropriate default total hydrocarbon population emission factors for storage wellheads in gas service listed in table W-3 to this subpart.

(4) LNG storage facilities must use the appropriate default methane population emission factors for LNG storage compressors in gas service listed in table W-5 to this subpart.

(5) LNG import and export facilities must use the appropriate default methane population emission factors for LNG terminal compressors in gas service listed in table W-5 to this subpart.

(6) Natural gas distribution facilities must use the appropriate methane emission factors as described in paragraphs (r)(6)(i) and (ii) of this section.

(i) Below grade transmission-distribution transfer stations, below grade metering-regulating stations, distribution mains, and distribution services must use the appropriate default methane population emission factors listed in table W-5 to this subpart to estimate emissions from components listed in § 98.232(i)(2), (4), (5), and (6), respectively.

(ii) Above grade metering-regulating stations that are not above grade transmission-distribution transfer stations must use the meter/regulator run population emission factor calculated in equation W-31 to this section in accordance with paragraph (q)(2)(x) or (q)(3)(viii)(A) of this section for the components listed in § 98.232(i)(3). Natural gas distribution facilities that do not have above grade transmission-distribution transfer stations are not required to calculate emissions for above grade metering-regulating stations and are not required to report GHG emissions in § 98.236(r)(2)(v).

(7) Onshore natural gas transmission pipeline facilities must use the appropriate default methane population emission factors listed in table W-5 to this subpart to estimate emissions from components listed in § 98.232(m)(3)(i), (4)(i) and (5).

(r) This paragraph (r) applies to emissions sources listed in § 98.232(c)(21)(ii), (f)(7), (g)(5), (h)(6), (j)(10)(ii), (m)(3)(i), and (m)(4)(i) if you are not required to comply with paragraph (q) of this section and if you do not elect to comply with paragraph (q) of this section for these components in lieu of this paragraph (r). This paragraph (r) also applies to emission sources listed in § 98.232(i)(2) through (6), (j)(11), and (m)(5). To be subject to the requirements of this paragraph (r), the listed emissions sources also must contact streams with gas content greater than 10 percent CH4 plus CO2 by weight. Emissions sources that contact streams with gas content less than or equal to 10 percent CH4 plus CO2 by weight are exempt from the requirements of this paragraph (r) and do not need to be reported. Tubing systems equal to or less than one half inch diameter are exempt from the requirements of this paragraph (r) and do not need to be reported. Equipment leak components in vacuum service are exempt from the survey and emission estimation requirements of this paragraph (r) and only the count of these equipment must be reported. You must calculate emissions from all emission sources listed in this paragraph (r) using equation W-32A to this section, except for natural gas distribution facility emission sources listed in § 98.232(i)(3). Natural gas distribution facility emission sources listed in § 98.232(i)(3) must calculate emissions using equation W-32B to this section and according to paragraph (r)(6)(ii) of this section.

(1) Calculate both CH4 and CO2 mass emissions from volumetric emissions using calculations in paragraph (v) of this section.

(2) Onshore petroleum and natural gas production facilities and onshore petroleum and natural gas gathering and boosting facilities must use the appropriate default whole gas population emission factors listed in table W-1 to this subpart. Major equipment associated with gas wells are considered gas service equipment in table W-1 to this subpart. Onshore petroleum and natural gas gathering and boosting facilities shall use the gas service equipment emission factors in table W-1 to this subpart. Major equipment associated with crude oil wells are considered crude service equipment in table W-1 to this subpart. Where facilities conduct EOR operations, the emission factor listed in table W-1 to this subpart shall be used to estimate all streams of gases, including recycle CO2 stream. For meters/piping, use one meters/piping per well-pad for onshore petroleum and natural gas production operations and the number of meters in the facility for onshore petroleum and natural gas gathering and boosting operations.

(3) Underground natural gas storage facilities must use the appropriate default total hydrocarbon population emission factors for storage wellheads in gas service listed in table W-3 to this subpart.

(4) LNG storage facilities must use the appropriate default methane population emission factors for LNG storage compressors in gas service listed in table W-5 to this subpart.

(5) LNG import and export facilities must use the appropriate default methane population emission factors for LNG terminal compressors in gas service listed in table W-5 to this subpart.

(6) Natural gas distribution facilities must use the appropriate methane emission factors as described in paragraphs (r)(6)(i) and (ii) of this section.

(i) Below grade transmission-distribution transfer stations, below grade metering-regulating stations, distribution mains, and distribution services must use the appropriate default methane population emission factors listed in table W-5 to this subpart to estimate emissions from components listed in § 98.232(i)(2), (4), (5), and (6), respectively.

(ii) Above grade metering-regulating stations that are not above grade transmission-distribution transfer stations must use the meter/regulator run population emission factor calculated in equation W-31 to this section in accordance with paragraph (q)(2)(x) or (q)(3)(viii)(A) of this section for the components listed in § 98.232(i)(3). Natural gas distribution facilities that do not have above grade transmission-distribution transfer stations are not required to calculate emissions for above grade metering-regulating stations and are not required to report GHG emissions in § 98.236(r)(2)(v).

(7) Onshore natural gas transmission pipeline facilities must use the appropriate default methane population emission factors listed in table W-5 to this subpart to estimate emissions from components listed in § 98.232(m)(3)(i), (4)(i) and (5).

(r) This paragraph (r) applies to emissions sources listed in § 98.232(c)(21)(ii), (f)(7), (g)(5), (h)(6), (j)(10)(ii), (m)(3)(i), and (m)(4)(i) if you are not required to comply with paragraph (q) of this section and if you do not elect to comply with paragraph (q) of this section for these components in lieu of this paragraph (r). This paragraph (r) also applies to emission sources listed in § 98.232(i)(2) through (6), (j)(11), and (m)(5). To be subject to the requirements of this paragraph (r), the listed emissions sources also must contact streams with gas content greater than 10 percent CH4 plus CO2 by weight. Emissions sources that contact streams with gas content less than or equal to 10 percent CH4 plus CO2 by weight are exempt from the requirements of this paragraph (r) and do not need to be reported. Tubing systems equal to or less than one half inch diameter are exempt from the requirements of this paragraph (r) and do not need to be reported. Equipment leak components in vacuum service are exempt from the survey and emission estimation requirements of this paragraph (r) and only the count of these equipment must be reported. You must calculate emissions from all emission sources listed in this paragraph (r) using equation W-32A to this section, except for natural gas distribution facility emission sources listed in § 98.232(i)(3). Natural gas distribution facility emission sources listed in § 98.232(i)(3) must calculate emissions using equation W-32B to this section and according to paragraph (r)(6)(ii) of this section.

(1) Calculate both CH4 and CO2 mass emissions from volumetric emissions using calculations in paragraph (v) of this section.

(2) Onshore petroleum and natural gas production facilities and onshore petroleum and natural gas gathering and boosting facilities must use the appropriate default whole gas population emission factors listed in table W-1 to this subpart. Major equipment associated with gas wells are considered gas service equipment in table W-1 to this subpart. Onshore petroleum and natural gas gathering and boosting facilities shall use the gas service equipment emission factors in table W-1 to this subpart. Major equipment associated with crude oil wells are considered crude service equipment in table W-1 to this subpart. Where facilities conduct EOR operations, the emission factor listed in table W-1 to this subpart shall be used to estimate all streams of gases, including recycle CO2 stream. For meters/piping, use one meters/piping per well-pad for onshore petroleum and natural gas production operations and the number of meters in the facility for onshore petroleum and natural gas gathering and boosting operations.

(3) Underground natural gas storage facilities must use the appropriate default total hydrocarbon population emission factors for storage wellheads in gas service listed in table W-3 to this subpart.

(4) LNG storage facilities must use the appropriate default methane population emission factors for LNG storage compressors in gas service listed in table W-5 to this subpart.

(5) LNG import and export facilities must use the appropriate default methane population emission factors for LNG terminal compressors in gas service listed in table W-5 to this subpart.

(6) Natural gas distribution facilities must use the appropriate methane emission factors as described in paragraphs (r)(6)(i) and (ii) of this section.

(i) Below grade transmission-distribution transfer stations, below grade metering-regulating stations, distribution mains, and distribution services must use the appropriate default methane population emission factors listed in table W-5 to this subpart to estimate emissions from components listed in § 98.232(i)(2), (4), (5), and (6), respectively.

(ii) Above grade metering-regulating stations that are not above grade transmission-distribution transfer stations must use the meter/regulator run population emission factor calculated in equation W-31 to this section in accordance with paragraph (q)(2)(x) or (q)(3)(viii)(A) of this section for the components listed in § 98.232(i)(3). Natural gas distribution facilities that do not have above grade transmission-distribution transfer stations are not required to calculate emissions for above grade metering-regulating stations and are not required to report GHG emissions in § 98.236(r)(2)(v).

(7) Onshore natural gas transmission pipeline facilities must use the appropriate default methane population emission factors listed in table W-5 to this subpart to estimate emissions from components listed in § 98.232(m)(3)(i), (4)(i) and (5).

(z) If your facility is required by § 98.232(c)(22), (i)(7), or (j)(12) to report emissions from combustion equipment, then you must indicate whether your facility has any combustion units subject to reporting according to paragraph (a)(1)(xx), (a)(8)(vi), or (a)(9)(xiii) of this section. If your facility contains any combustion units subject to reporting according to paragraph (a)(1)(xx), (a)(8)(vi), or (a)(9)(xiii) of this section, then you must report the information specified in paragraphs (z)(1) and (2) of this section, as applicable. You must report the information specified in paragraphs (z)(1) and (2) of this section, as applicable, for each well-pad site (for onshore petroleum and natural gas production), gathering and boosting site (for onshore petroleum and natural gas gathering and boosting), or facility (for all other applicable industry segments).

(1) External fuel combustion units with a rated heat capacity less than or equal to 5 million Btu per hour; or, internal fuel combustion units that are not compressor-drivers, with a rated heat capacity less than or equal to 1 mmBtu/hr (or the equivalent of 130 horsepower). If the facility contains external fuel combustion units with a rated heat capacity less than or equal to 5 million Btu per hour or internal fuel combustion units that are not compressor-drivers, with a rated heat capacity less than or equal to 1 million Btu per hour (or the equivalent of 130 horsepower), then you must report the information specified in paragraphs (z)(1)(i) through (iii) of this section for each unit type.

(i) Well-pad ID (for the onshore petroleum and natural gas production industry segment only) or gathering and boosting site ID (for the onshore petroleum and natural gas gathering and boosting industry segment only).

(2) External fuel combustion units with a rated heat capacity greater than 5 million Btu per hour; internal fuel combustion units that are not compressor-drivers, with a rated heat capacity greater than 1 million Btu per hour (or the equivalent of 130 horsepower); or, internal fuel combustion units of any heat capacity that are compressor-drivers. For each type of combustion unit at your facility, you must report the information specified in paragraphs (z)(2)(i) through (iv) and (z)(2)(viii) through (x) of this section, except for internal fuel combustion units that are not compressor-drivers, with a rated heat capacity greater than 1 million Btu per hour (or the equivalent of 130 horsepower) or internal fuel combustion units of any heat capacity that are compressor-drivers that combust natural gas meeting the criteria in § 98.233(z)(1) or (2) or a fuel meeting the criteria in § 98.233(z)(3), which must report the information specified in paragraphs (z)(2)(i) through (x) of this section. Information must be reported for each combustion unit type, fuel type, and method for determining the CH4 emission factor combination, as applicable.

(i) Well-pad ID (for the onshore petroleum and natural gas production industry segment only) or gathering and boosting site ID (for the onshore petroleum and natural gas gathering and boosting industry segment only).

(ii) The type of combustion unit including external fuel combustion units with a rated heat capacity greater than 5 million Btu per hour; internal fuel combustion units that are not compressor-drivers, with a rated heat capacity greater than 1 million Btu per hour (or the equivalent of 130 horsepower); or internal fuel combustion units of any heat capacity that are compressor-drivers.

(iv) The quantity of fuel combusted in the calendar year, in thousand standard cubic feet, gallons, or tons.

(v) The equipment type, including reciprocating 2-stroke-lean burn, reciprocating 4-stroke lean-burn, reciprocating 4-stroke rich-burn, and gas turbine.

(vi) The method used to determine the methane emission factor, including the default emission factor from table W-7 to this subpart, OEM data, or performance tests in § 98.234(i) for natural gas described in § 98.233(z)(1) or (2), or performance tests in § 98.234(i) or default combustion efficiency for fuels described in section § 98.233(z)(3).

(vii) If multiple performance tests were performed in the same reporting year, the arithmetic average value of CH4 emission factor (kg CH4/mmBtu). This information is not required if CH4 emissions were calculated per § 98.233(z)(3)(ii)(D).

(viii) Annual CO2 emissions, in metric tons CO2, calculated according to § 98.233(z)(1) through (3).

(ix) Annual CH4 emissions, in metric tons CH4, calculated according to § 98.233(z)(1) through (3).

(x) Annual N2O emissions, in metric tons N2O, calculated according to § 98.233(z)(1) through (3).

Except as provided in this section, all terms used in this subpart have the same meaning given in the Clean Air Act and subpart A of this part.

(3) Facilities must report emissions from the onshore petroleum and natural gas gathering and boosting industry segment only if emission sources specified in § 98.232(j) emit 25,000 metric tons of CO2 equivalent or more per year.

(a) You must report CO2, CH4, and N2O emissions from each industry segment specified in paragraphs (b) through (j) and (m) of this section, CO2, CH4, and N2O emissions from each flare as specified in paragraphs (b) through (j) of this section, and stationary and portable combustion emissions as applicable as specified in paragraph (k) of this section. You must also report the information specified in paragraph (l) of this section, as applicable.

(1) If the entire facility is acquired by an owner or operator that does not already have a reporting facility in the same industry segment and basin (for onshore petroleum and natural gas production or onshore petroleum and natural gas gathering and boosting) or state (for natural gas distribution), then within 90 days after the change in the owner or operator, the designated representative or any alternate designated representative shall submit a certificate of representation that is complete under this section. If the new owner or operator already had emission sources specified in § 98.232(c), (i), (j), or (m), as applicable, prior to the acquisition in the same basin (for onshore petroleum and natural gas production or onshore petroleum and natural gas gathering and boosting) or state (for natural gas distribution) as the acquired facility but had not previously met the applicability requirements in §§ 98.2(a) and 98.231, then per the applicable definition of facility in § 98.238, the previously owned applicable emission sources must be included in the acquired facility. The new owner or operator and the new designated representative shall be responsible for submitting the annual report for the facility for the entire reporting year beginning with the reporting year in which the acquisition occurred.

(o) If you are required to report emissions from centrifugal compressor venting as specified in § 98.232(d)(2), (e)(2), (f)(2), (g)(2), and (h)(2), you must conduct volumetric emission measurements specified in paragraph (o)(1) of this section using methods specified in paragraphs (o)(2) through (5) of this section; perform calculations specified in paragraphs (o)(6) through (9) of this section; and calculate CH4 and CO2 mass emissions as specified in paragraph (o)(11) of this section. If you are required to report emissions from centrifugal compressor venting at an onshore petroleum and natural gas production facility as specified in § 98.232(c)(19) or an onshore petroleum and natural gas gathering and boosting facility as specified in § 98.232(j)(8), you must calculate volumetric emissions as specified in paragraph (o)(10) of this section and calculate CH4 and CO2 mass emissions as specified in paragraph (o)(11) of this section. If emissions from a compressor source are routed to a flare, paragraphs (o)(1) through (11) of this section do not apply and instead you must calculate CH4, CO2, and N2O emissions as specified in paragraph (n) of this section and report emissions from the flare as specified in § 98.236(n). If emissions from a compressor source are routed to combustion, paragraphs (o)(1) through (11) of this section do not apply and instead you must calculate and report emissions as specified in subpart C of this part or paragraph (z) of this section, as applicable. If emissions from a compressor source are routed to a vapor recovery system, paragraphs (o)(1) through (11) of this section do not apply.

(1) You must conduct volumetric emission measurements on each centrifugal compressor as specified in this paragraph. Compressor sources (as defined in § 98.238) without manifolded vents must use a measurement method specified in paragraph (o)(1)(i) or (ii) of this section. Manifolded compressor sources (as defined in § 98.238) must use a measurement method specified in paragraph (o)(1)(i), (ii), (iii), or (iv) of this section.

(i) Measure venting from each compressor according to either paragraph (o)(1)(i)(A), (B), or (C) of this section at least once annually, based on the compressor mode (as defined in § 98.238) in which the compressor was found at the time of measurement, except as specified in paragraph (o)(1)(i)(D) of this section. If additional measurements beyond the required annual testing are performed (including duplicate measurements or measurement of additional operating modes), then all measurements satisfying the applicable monitoring and QA/QC that is required by this paragraph (o) must be used in the calculations specified in this section.

(A) For a compressor measured in operating-mode, you must measure volumetric emissions from blowdown valve leakage through the blowdown vent as specified in paragraph (o)(2)(i) of this section, measure volumetric emissions from wet seal oil degassing vents as specified in paragraph (o)(2)(ii) of this section if the compressor has wet seal oil degassing vents, and measure volumetric emissions from dry seal vents as specified in paragraph (o)(2)(iii) of this section if the compressor has dry seals.

(B) For a compressor measured in not-operating-depressurized-mode, you must measure volumetric emissions from isolation valve leakage as specified in paragraph (o)(2)(i) of this section. If a compressor is not operated and has blind flanges in place throughout the reporting period, measurement is not required in this compressor mode.

(C) For a compressor measured in standby-pressurized-mode, you must measure volumetric emissions from blowdown valve leakage through the blowdown vent as specified in paragraph (o)(2)(i) of this section, measure volumetric emissions from wet seal oil degassing vents as specified in paragraph (o)(2)(ii) of this section if the compressor has wet seal oil degassing vents, and measure volumetric emissions from dry seal vents as specified in paragraph (o)(2)(iii) of this section if the compressor has dry seals.

(D) An annual as found measurement is not required in the first year of operation for any new compressor that begins operation after as found measurements have been conducted for all existing compressors. For only the first year of operation of new compressors, calculate emissions according to paragraph (o)(6)(ii) of this section.

(ii) Instead of measuring the compressor source according to paragraph (o)(1)(i) of this section for a given compressor, you may elect to continuously measure volumetric emissions from a compressor source as specified in paragraph (o)(3) of this section.

(iii) For a compressor source that is part of a manifolded group of compressor sources (as defined in § 98.238), instead of measuring the compressor source according to paragraph (o)(1)(i), (ii), or (iv) of this section, you may elect to measure combined volumetric emissions from the manifolded group of compressor sources by conducting measurements at the common vent stack as specified in paragraph (o)(4) of this section. The measurements must be conducted at the frequency specified in paragraphs (o)(1)(iii)(A) and (B) of this section.

(A) A minimum of one measurement must be taken for each manifolded group of compressor sources in a calendar year.

(B) The measurement may be performed while the compressors are in any compressor mode.

(iv) For a compressor source that is part of a manifolded group of compressor sources, instead of measuring the compressor source according to paragraph (o)(1)(i), (ii), or (iii) of this section, you may elect to continuously measure combined volumetric emissions from the manifolded group of compressor sources as specified in paragraph (o)(5) of this section.

(2) . If conducting measurements for each compressor source, you must determine the volumetric emissions from blowdown valves and isolation valves as specified in paragraph (o)(2)(i) of this section, the volumetric emissions from wet seal oil degassing vents as specified in paragraph (o)(2)(ii) of this section, and the volumetric emissions from dry seal vents as specified in paragraph (o)(2)(iii) of this section.

(i) For blowdown valves on compressors in operating-mode or in standby-pressurized-mode and for isolation valves on compressors in not-operating-depressurized-mode, determine the volumetric emissions using one of the methods specified in paragraphs (o)(2)(i)(A) through (D) of this section.

(A) Determine the volumetric flow at standard conditions from the blowdown vent using calibrated bagging or high volume sampler according to methods set forth in § 98.234(c) and § 98.234(d), respectively.

(B) Determine the volumetric flow at standard conditions from the blowdown vent using a temporary meter such as a vane anemometer according to methods set forth in § 98.234(b).

(C) Use an acoustic leak detection device according to methods set forth in § 98.234(a)(5).

(D) You may choose to use any of the methods set forth in § 98.234(a) to screen for emissions. If emissions are detected using the methods set forth in § 98.234(a), then you must use one of the methods specified in paragraph (o)(2)(i)(A) through (C) of this section. If emissions are not detected using the methods in § 98.234(a), then you may assume that the volumetric emissions are zero. For the purposes of this paragraph, when using any of the methods in § 98.234(a), emissions are detected whenever a leak is detected according to the methods.

(ii) For wet seal oil degassing vents in operating-mode or in standby-pressurized-mode, determine volumetric flow at standard conditions, using one of the methods specified in paragraphs (o)(2)(ii)(A) through (C) of this section. You must quantitatively measure the volumetric flow for wet seal oil degassing vent; you may not use screening methods set forth in § 98.234(a) to screen for emissions for the wet seal oil degassing vent.

(A) Use a temporary meter such as a vane anemometer or permanent flow meter according to methods set forth in § 98.234(b).

(B) Use calibrated bags according to methods set forth in § 98.234(c).

(C) Use a high volume sampler according to methods set forth in § 98.234(d).

(iii) For dry seal vents in operating-mode or in standby-pressurized-mode, determine volumetric flow at standard conditions from each dry seal vent using one of the methods specified in paragraphs (o)(2)(iii)(A) through (D) of this section. The measurement should be conducted on the compressor side dry seal. If a compressor has more than one dry seal vent, determine the aggregate dry seal vent volumetric flow for the compressor as the sum of the volumetric flows determined for each dry seal vent on the compressor.

(A) Use a temporary meter such as a vane anemometer or permanent flow meter according to methods set forth in § 98.234(b).

(B) Use calibrated bags according to methods set forth in § 98.234(c).

(C) Use a high volume sampler according to methods set forth in § 98.234(d).

(D) You may choose to use any of the methods set forth in § 98.234(a)(1) through (3) to screen for emissions. If emissions are detected using one of these specified methods, then you must use one of the methods specified in paragraph (o)(2)(iii)(A) through (C) of this section. If emissions are not detected using the methods in § 98.234(a)(1) through (3), then you may assume that the volumetric emissions are zero. For the purposes of this paragraph, when using any of the methods in § 98.234(a), emissions are detected whenever a leak is detected according to the methods. Acoustic leak detection is only applicable for through-valve leakage and is not applicable for screening dry seal vents.

(3) If you elect to conduct continuous volumetric emission measurements for an individual compressor source as specified in paragraph (o)(1)(ii) of this section, you must measure volumetric emissions as specified in paragraphs (o)(3)(i) and (ii) of this section.

(i) Continuously measure the volumetric flow for the individual compressor source at standard conditions using a permanent meter according to methods set forth in § 98.234(b).

(ii) If compressor blowdown emissions are included in the metered emissions specified in paragraph (o)(3)(i) of this section, the compressor blowdown emissions may be included with the reported emissions for the compressor source and do not need to be calculated separately using the method specified in paragraph (i) of this section for blowdown vent stacks.

(4) If conducting measurements for a manifolded group of compressor sources, you must measure volumetric emissions as specified in paragraphs (o)(4)(i) and (ii) of this section.

(i) Measure at a single point in the manifold downstream of all compressor inputs and, if practical, prior to comingling with other non-compressor emission sources.

(ii) Determine the volumetric flow at standard conditions from the common stack using one of the methods specified in paragraphs (o)(4)(ii)(A) through (F) of this section.

(A) A temporary meter such as a vane anemometer according the methods set forth in § 98.234(b).

(B) Calibrated bagging according to methods set forth in § 98.234(c).

(C) A high volume sampler according to methods set forth § 98.234(d).

(D) [Reserved]

(E) You may choose to use any of the methods set forth in § 98.234(a)(1) through (3) to screen for emissions. If emissions are detected using one of these methods, then you must use one of the methods specified in paragraph (o)(4)(ii)(A) through (D) of this section. If emissions are not detected using the methods in § 98.234(a)(1) through (3), then you may assume that the volumetric emissions are zero. For the purposes of this paragraph, when using any of the methods in § 98.234(a), emissions are detected whenever a leak is detected according to the method. Acoustic leak detection is only applicable for through-valve leakage and is not applicable for screening a manifolded group of compressor sources.

(F) If one of the screening methods specified in § 98.234(a)(1) through (3) identifies a leak in a manifolded group of centrifugal compressor sources, you may use acoustic leak detection, according to § 98.234(a)(5), to identify the source of the leak. You must use one of the methods specified in paragraphs (o)(4)(ii)(A) through (D) of this section to quantify emissions from the identified source.

(5) If you elect to conduct continuous volumetric emission measurements for a manifolded group of compressor sources as specified in paragraph (o)(1)(iv) of this section, you must measure volumetric emissions as specified in paragraphs (o)(5)(i) through (iii) of this section.

(i) Measure at a single point in the manifold downstream of all compressor inputs and, if practical, prior to comingling with other non-compressor emission sources.

(ii) Continuously measure the volumetric flow for the manifolded group of compressor sources at standard conditions using a permanent meter according to methods set forth in § 98.234(b).

(iii) If compressor blowdown emissions are included in the metered emissions specified in paragraph (o)(5)(ii) of this section, the compressor blowdown emissions may be included with the reported emissions for the manifolded group of compressor sources and do not need to be calculated separately using the method specified in paragraph (i) of this section for blowdown vent stacks.

(6) . For compressor sources measured according to paragraph (o)(1)(i) of this section, you must calculate annual GHG emissions from the compressor sources as specified in paragraphs (o)(6)(i) through (iv) of this section.

(i) Using equation W-21 to this section, calculate the annual volumetric GHG emissions for each centrifugal compressor mode-source combination specified in paragraphs (o)(1)(i)(A) through (C) of this section that was measured during the reporting year.

(ii) Using equation W-22 to this section, calculate the annual volumetric GHG emissions from each centrifugal compressor mode-source combination specified in paragraphs (o)(1)(i)(A) through (C) of this section that was not measured during the reporting year.

(iii) Using equation W-23 to this section, develop an emission factor for each compressor mode-source combination specified in paragraphs (o)(1)(i)(A) through (C) of this section. These emission factors must be calculated annually and used in equation W-22 to this section to determine volumetric emissions from a centrifugal compressor in the mode- source combinations that were not measured in the reporting year.

(iv) The reporter emission factor in equation W-23 to this section may be calculated by using all measurements from a single owner or operator instead of only using measurements from a single facility. If you elect to use this option, the reporter emission factor must be applied to all reporting facilities for the owner or operator.

(7) . For compressor sources measured according to paragraph (o)(1)(ii) of this section, you must use the continuous volumetric emission measurements taken as specified in paragraph (o)(3) of this section and calculate annual volumetric GHG emissions associated with the compressor source using equation W-24A to this section.

(8) . For manifolded groups of compressor sources measured according to paragraph (o)(1)(iii) of this section, you must calculate annual volumetric GHG emissions using equation W-24B to this section. If the centrifugal compressors included in the manifolded group of compressor sources share the manifold with reciprocating compressors, you must follow the procedures in either this paragraph (o)(8) or paragraph (p)(8) of this section to calculate emissions from the manifolded group of compressor sources.

(9) For a manifolded group of compressor sources measured according to paragraph (o)(1)(iv) of this section, you must use the continuous volumetric emission measurements taken as specified in paragraph (o)(5) of this section and calculate annual volumetric GHG emissions associated with each manifolded group of compressor sources using equation W-24C to this section. If the centrifugal compressors included in the manifolded group of compressor sources share the manifold with reciprocating compressors, you must follow the procedures in either this paragraph (o)(9) or paragraph (p)(9) of this section to calculate emissions from the manifolded group of compressor sources.

(10) You must calculate volumetric emissions from centrifugal compressors at an onshore petroleum and natural gas production facility or an onshore petroleum and natural gas gathering and boosting facility as specified in paragraphs (o)(10)(i) through (iv), as applicable.

(i) For all centrifugal compressors at an onshore petroleum and natural gas production facility or an onshore petroleum and natural gas gathering and boosting facility that are subject to the centrifugal compressor standards in § 60.5380b of this chapter or an applicable approved state plan or applicable Federal plan in part 62 of this chapter for dry seals and self-contained wet seals, you must conduct the volumetric emission measurements as required by § 60.5380b(a)(5) of this chapter or an applicable approved state plan or applicable Federal plan in part 62 of this chapter, conduct all additional volumetric emission measurements specified in paragraph (o)(1) of this section using methods specified in paragraphs (o)(2) through (5) of this section (based on the compressor mode (as defined in § 98.238) in which the compressor was found at the time of measurement), and calculate emissions as specified in paragraphs (o)(6) through (9) of this section. Conduct all measurements required by this paragraph (o)(10)(i) at the frequency specified by § 60.5380b(a)(4) of this chapter or an applicable approved state plan or applicable Federal plan in part 62 of this chapter. For any reporting year in which measuring at the frequency specified by § 60.5380b(a)(4) of this chapter results in measurement not being required for a subject compressor, calculate emissions for all mode-source combinations as specified in paragraph (o)(6)(ii) of this section.

(ii) For all centrifugal compressors at an onshore petroleum and natural gas production facility or an onshore petroleum and natural gas gathering and boosting facility that are not subject to the centrifugal compressor standards in § 60.5380b of this chapter or an applicable approved state plan or applicable Federal plan in part 62 of this chapter for dry seals and self-contained wet seals, you may elect to conduct the volumetric emission measurements specified in paragraph (o)(1) of this section using methods specified in paragraphs (o)(2) through (5) of this section (based on the compressor mode (as defined in § 98.238) in which the compressor was found at the time of measurement), and calculate emissions as specified in paragraphs (o)(6) through (9) of this section.

(iii) For all centrifugal compressors at an onshore petroleum and natural gas production facility or an onshore petroleum and natural gas gathering and boosting facility for which paragraph (o)(10)(i) of this section does not apply and you do not elect to conduct the volumetric measurements specified in paragraph (o)(1) of this section, you must calculate total atmospheric wet seal oil degassing vent emissions from all centrifugal compressors at either an onshore petroleum and natural gas production facility or an onshore petroleum and natural gas gathering and boosting facility using equation W-25A to this section. Emissions from centrifugal compressor wet seal oil degassing vents that are routed to a flare, combustion, or vapor recovery system are not required to be determined under this paragraph (o).

(iv) For all centrifugal compressors at an onshore petroleum and natural gas production facility or an onshore petroleum and natural gas gathering and boosting facility for which paragraph (o)(10)(i) of this section does not apply, and you do not elect to conduct the volumetric measurements specified in paragraph (o)(1) of this section, you must calculate wet seal oil degassing vent emissions from each centrifugal compressor using equation W-25B to this section. Emissions from centrifugal compressor wet seal oil degassing vents that are routed to a flare, combustion, or vapor recovery system are not required to be determined under this paragraph (o).

(11) . You must calculate both CH4 and CO2 mass emissions from volumetric emissions using calculations in paragraph (v) of this section.

(p) If you are required to report emissions from reciprocating compressor venting as specified in § 98.232(d)(1), (e)(1), (f)(1), (g)(1), and (h)(1), you must conduct volumetric emission measurements specified in paragraph (p)(1) of this section using methods specified in paragraphs (p)(2) through (5) of this section; perform calculations specified in paragraphs (p)(6) through (9) of this section; and calculate CH4 and CO2 mass emissions as specified in paragraph (p)(11) of this section. If you are required to report emissions from reciprocating compressor venting at an onshore petroleum and natural gas production facility as specified in § 98.232(c)(11) or an onshore petroleum and natural gas gathering and boosting facility as specified in § 98.232(j)(9), you must calculate volumetric emissions as specified in paragraph (p)(10) of this section and calculate CH4 and CO2 mass emissions as specified in paragraph (p)(11) of this section. If emissions from a compressor source are routed to a flare, paragraphs (p)(1) through (11) of this section do not apply and instead you must calculate CH4, CO2, and N2O emissions as specified in paragraph (n) of this section and report emissions from the flare as specified in § 98.236(n). If emissions from a compressor source are routed to combustion, paragraphs (p)(1) through (11) of this section do not apply and instead you must calculate and report emissions as specified in subpart C of this part or paragraph (z) of this section, as applicable. If emissions from a compressor source are routed to a vapor recovery system, paragraphs (p)(1) through (11) of this section do not apply.

(1) You must conduct volumetric emission measurements on each reciprocating compressor as specified in this paragraph. Compressor sources (as defined in § 98.238) without manifolded vents must use a measurement method specified in paragraph (p)(1)(i) or (ii) of this section. Manifolded compressor sources (as defined in § 98.238) must use a measurement method specified in paragraph (p)(1)(i), (ii), (iii), or (iv) of this section.

(i) Measure venting from each compressor according to either paragraph (p)(1)(i)(A), (B), or (C) of this section at least once annually, based on the compressor mode (as defined in § 98.238) in which the compressor was found at the time of measurement, except as specified in paragraph (p)(1)(i)(D) of this section. If additional measurements beyond the required annual testing are performed (including duplicate measurements or measurement of additional operating modes), then all measurements satisfying the applicable monitoring and QA/QC that is required by this paragraph (p) must be used in the calculations specified in this section.

(A) For a compressor measured in operating-mode, you must measure volumetric emissions from blowdown valve leakage through the blowdown vent as specified in paragraph (p)(2)(i) of this section, and measure volumetric emissions from reciprocating rod packing as specified in paragraph (p)(2)(ii) or (iii) of this section, as applicable.

(B) For a compressor measured in not-operating-depressurized-mode, you must measure volumetric emissions from isolation valve leakage as specified in paragraph (p)(2)(i) of this section. If a compressor is not operated and has blind flanges in place throughout the reporting period, measurement is not required in this compressor mode.

(C) For a compressor measured in standby-pressurized-mode, you must measure volumetric emissions from blowdown valve leakage through the blowdown vent as specified in paragraph (p)(2)(i) of this section and measure volumetric emissions from reciprocating rod packing as specified in paragraph (p)(2)(ii) or (iii) of this section, as applicable.

(D) An annual as found measurement is not required in the first year of operation for any new compressor that begins operation after as found measurements have been conducted for all existing compressors. For only the first year of operation of new compressors, calculate emissions according to paragraph (p)(6)(ii) of this section.

(ii) Instead of measuring the compressor source according to paragraph (p)(1)(i) of this section for a given compressor, you may elect to continuously measure volumetric emissions from a compressor source as specified in paragraph (p)(3) of this section.

(iii) For a compressor source that is part of a manifolded group of compressor sources (as defined in § 98.238), instead of measuring the compressor source according to paragraph (p)(1)(i), (ii), or (iv) of this section, you may elect to measure combined volumetric emissions from the manifolded group of compressor sources by conducting measurements at the common vent stack as specified in paragraph (p)(4) of this section. The measurements must be conducted at the frequency specified in paragraphs (p)(1)(iii)(A) and (B) of this section.

(A) A minimum of one measurement must be taken for each manifolded group of compressor sources in a calendar year.

(B) The measurement may be performed while the compressors are in any compressor mode.

(iv) For a compressor source that is part of a manifolded group of compressor sources, instead of measuring the compressor source according to paragraph (p)(1)(i), (ii), or (iii) of this section, you may elect to continuously measure combined volumetric emissions from the manifolded group of compressors sources as specified in paragraph (p)(5) of this section.

(2) . If conducting measurements for each compressor source, you must determine the volumetric emissions from blowdown valves and isolation valves as specified in paragraph (p)(2)(i) of this section. You must determine the volumetric emissions from reciprocating rod packing as specified in paragraph (p)(2)(ii) or (iii) of this section, as applicable.

(i) and for isolation valves on compressors in not-operating-depressurized-mode, determine the volumetric emissions using one of the methods specified in paragraphs (p)(2)(i)(A) through (D) of this section.

(A) Determine the volumetric flow at standard conditions from the blowdown vent using calibrated bagging or high volume sampler according to methods set forth in § 98.234(c) and (d), respectively.

(B) Determine the volumetric flow at standard conditions from the blowdown vent using a temporary meter such as a vane anemometer, according to methods set forth in § 98.234(b).

(C) Use an acoustic leak detection device according to methods set forth in § 98.234(a)(5).

(D) You may choose to use any of the methods set forth in § 98.234(a) to screen for emissions. If emissions are detected using the methods set forth in § 98.234(a), then you must use one of the methods specified in paragraphs (p)(2)(i)(A) through (C) of this section. If emissions are not detected using the methods in § 98.234(a), then you may assume that the volumetric emissions are zero. For the purposes of this paragraph, when using any of the methods in § 98.234(a), emissions are detected whenever a leak is detected according to the method.

(ii) For reciprocating rod packing equipped with an open-ended vent line on compressors in operating-mode or standby-pressurized-mode, determine the volumetric emissions using one of the methods specified in paragraphs (p)(2)(ii)(A) through (C) of this section.

(A) Determine the volumetric flow at standard conditions from the open-ended vent line using calibrated bagging or high volume sampler according to methods set forth in § 98.234(c) and (d), respectively.

(B) Determine the volumetric flow at standard conditions from the open-ended vent line using a temporary meter such as a vane anemometer, according to methods set forth in § 98.234(b).

(C) You may choose to use any of the methods set forth in § 98.234(a)(1) through (3) to screen for emissions. If emissions are detected using one of these specified methods, then you must use one of the methods specified in paragraphs (p)(2)(ii)(A) and (B) of this section. If emissions are not detected using the methods in § 98.234(a)(1) through (3), then you may assume that the volumetric emissions are zero. For the purposes of this paragraph (p)(2)(ii)(C), when using any of the methods in § 98.234(a), emissions are detected whenever a leak is detected according to the method. Acoustic leak detection is only applicable for through-valve leakage and is not applicable for screening or measuring rod packing emissions.

(iii) For reciprocating rod packing not equipped with an open-ended vent line on compressors in operating-mode, you must determine the volumetric emissions using the method specified in paragraphs (p)(2)(iii)(A) and (B) of this section.

(A) You must use the methods described in § 98.234(a)(1) through (3) to conduct annual leak detection of equipment leaks from the packing case into an open distance piece, or for compressors with a closed distance piece, conduct annual detection of gas emissions from the rod packing vent, distance piece vent, compressor crank case breather cap, or other vent emitting gas from the rod packing. Acoustic leak detection is only applicable for through-valve leakage and is not applicable for screening rod packing emissions.

(B) You must measure emissions found in paragraph (p)(2)(iii)(A) of this section using an appropriate meter, calibrated bag, or high volume sampler according to methods set forth in § 98.234(b), (c), and (d), respectively.

(3) . If you elect to conduct continuous volumetric emission measurements for an individual compressor source as specified in paragraph (p)(1)(ii) of this section, you must measure volumetric emissions as specified in paragraphs (p)(3)(i) and (p)(3)(ii) of this section.

(i) Continuously measure the volumetric flow for the individual compressor sources at standard conditions using a permanent meter according to methods set forth in § 98.234(b).

(ii) If compressor blowdown emissions are included in the metered emissions specified in paragraph (p)(3)(i) of this section, the compressor blowdown emissions may be included with the reported emissions for the compressor source and do not need to be calculated separately using the method specified in paragraph (i) of this section for blowdown vent stacks.

(4) . If conducting measurements for a manifolded group of compressor sources, you must measure volumetric emissions as specified in paragraphs (p)(4)(i) and (ii) of this section.

(i) Measure at a single point in the manifold downstream of all compressor inputs and, if practical, prior to comingling with other non-compressor emission sources.

(ii) Determine the volumetric flow at standard conditions from the common stack using one of the methods specified in paragraphs (p)(4)(ii)(A) through (F) of this section.

(A) A temporary meter such as a vane anemometer according to methods set forth in § 98.234(b).

(B) Calibrated bagging according to methods set forth in § 98.234(c).

(C) A high volume sampler according to methods set forth in § 98.234(d).

(D) [Reserved]

(E) You may choose to use any of the methods set forth in § 98.234(a)(1) through (3) to screen for emissions. If emissions are detected using one of these specified methods, then you must use one of the methods specified in paragraphs (p)(4)(ii)(A) through (D) of this section. If emissions are not detected using the methods in § 98.234(a)(1) through (3), then you may assume that the volumetric emissions are zero. For the purposes of this paragraph, when using any of the methods in § 98.234(a), emissions are detected whenever a leak is detected according to the method. Acoustic leak detection is only applicable for through-valve leakage and is not applicable for screening a manifolded group of compressor sources.

(F) If one of the screening methods specified in § 98.234(a)(1) through (3) identifies a leak in a manifolded group of reciprocating compressor sources, you may use acoustic leak detection, according to § 98.234(a)(5), to identify the source of the leak. You must use one of the methods specified in paragraphs (p)(4)(ii)(A) through (D) of this section to quantify the emissions from the identified source.

(5) . If you elect to conduct continuous volumetric emission measurements for a manifolded group of compressor sources as specified in paragraph (p)(1)(iv) of this section, you must measure volumetric emissions as specified in paragraphs (p)(5)(i) through (iii) of this section.

(i) Measure at a single point in the manifold downstream of all compressor inputs and, if practical, prior to comingling with other non-compressor emission sources.

(ii) Continuously measure the volumetric flow for the manifolded group of compressor sources at standard conditions using a permanent meter according to methods set forth in § 98.234(b).

(iii) If compressor blowdown emissions are included in the metered emissions specified in paragraph (p)(5)(ii) of this section, the compressor blowdown emissions may be included with the reported emissions for the manifolded group of compressor sources and do not need to be calculated separately using the method specified in paragraph (i) of this section for blowdown vent stacks.

(6) . For compressor sources measured according to paragraph (p)(1)(i) of this section, you must calculate GHG emissions from the compressor sources as specified in paragraphs (p)(6)(i) through (iv) of this section.

(i) Using equation W-26 to this section, calculate the annual volumetric GHG emissions for each reciprocating compressor mode-source combination specified in paragraphs (p)(1)(i)(A) through (C) of this section that was measured during the reporting year.

(ii) Using equation W-27 to this section, calculate the annual volumetric GHG emissions from each reciprocating compressor mode-source combination specified in paragraphs (p)(1)(i)(A) through (C) of this section that was not measured during the reporting year.

(iii) Using equation W-28 to this section, develop an emission factor for each compressor mode-source combination specified in paragraphs (p)(1)(i)(A) through (C) of this section. These emission factors must be calculated annually and used in equation W-27 to this section to determine volumetric emissions from a reciprocating compressor in the mode-source combinations that were not measured in the reporting year.

(iv) The reporter emission factor in equation W-28 to this section may be calculated by using all measurements from a single owner or operator instead of only using measurements from a single facility. If you elect to use this option, the reporter emission factor must be applied to all reporting facilities for the owner or operator.

(7) . For compressor sources measured according to paragraph (p)(1)(ii) of this section, you must use the continuous volumetric emission measurements taken as specified in paragraph (p)(3) of this section and calculate annual volumetric GHG emissions associated with the compressor source using equation W-29A to this section.

(8) For manifolded groups of compressor sources measured according to paragraph (p)(1)(iii) of this section, you must calculate annual GHG emissions using equation W-29B to this section. If the reciprocating compressors included in the manifolded group of compressor sources share the manifold with centrifugal compressors, you must follow the procedures in either this paragraph (p)(8) or paragraph (o)(8) of this section to calculate emissions from the manifolded group of compressor sources.

(9) . For a manifolded group of compressor sources measured according to paragraph (p)(1)(iv) of this section, you must use the continuous volumetric emission measurements taken as specified in paragraph (p)(5) of this section and calculate annual volumetric GHG emissions associated with each manifolded group of compressor sources using equation W-29C to this section. If the reciprocating compressors included in the manifolded group of compressor sources share the manifold with centrifugal compressors, you must follow the procedures in either this paragraph (p)(9) or paragraph (o)(9) of this section to calculate emissions from the manifolded group of compressor sources.

(10) . You must calculate volumetric emissions from reciprocating compressors at an onshore petroleum and natural gas production facility or an onshore petroleum and natural gas gathering and boosting facility as specified in paragraphs (p)(10)(i) through (iv) of this section, as applicable.

(i) For all reciprocating compressors at an onshore petroleum and natural gas production facility or an onshore petroleum and natural gas gathering and boosting facility that are subject to the reciprocating compressor standards in § 60.5385b of this chapter or an applicable approved state plan or applicable Federal plan in part 62 of this chapter, you must conduct the volumetric emission measurements as required by § 60.5385b(b) and (c) of this chapter or an applicable approved state plan or applicable Federal plan in part 62 of this chapter, conduct any additional volumetric emission measurements specified in paragraph (p)(1) of this section using methods specified in paragraphs (p)(2) through (5) of this section (based on the compressor mode (as defined in § 98.238) in which the compressor was found at the time of measurement), and calculate emissions as specified in paragraphs (p)(6) through (9) of this section. Conduct all measurements required by this paragraph (p)(10)(i) at the frequency specified by § 60.5385b(a) of this chapter or an applicable approved state plan or applicable Federal plan in part 62 of this chapter. For any reporting year in which measuring at the frequency specified by § 60.5385b(a) of this chapter results in measurement not being required for a subject compressor, calculate emissions for all mode-source combinations as specified in paragraph (p)(6)(ii) of this section.

(ii) For all reciprocating compressors at an onshore petroleum and natural gas production facility or an onshore petroleum and natural gas gathering and boosting facility that are not subject to the reciprocating compressor standards in § 60.5385b of this chapter or an applicable approved state plan or applicable Federal plan in part 62 of this chapter, you may elect to conduct volumetric emission measurements specified in paragraph (p)(1) of this section using methods specified in paragraphs (p)(2) through (5) of this section (based on the compressor mode (as defined in § 98.238) in which the compressor was found at the time of measurement), and calculate emissions as specified in paragraphs (p)(6) through (9) of this section.

(iii) For all reciprocating compressors at an onshore petroleum and natural gas production facility or an onshore petroleum and natural gas gathering and boosting facility for which paragraph (p)(10)(i) of this section does not apply, and you do not elect to conduct volumetric emission measurements specified in paragraph (p)(1) of this section, you must calculate total atmospheric rod packing emissions from all reciprocating compressors at either an onshore petroleum and natural gas production facility or an onshore petroleum and natural gas gathering and boosting facility using equation W-29D to this section. Reciprocating compressor rod packing emissions that are routed to a flare, combustion, or vapor recovery system are not required to be determined under this paragraph (p).

(iv) For all reciprocating compressors at an onshore petroleum and natural gas production facility or an onshore petroleum and natural gas gathering and boosting facility for which paragraph (p)(10)(i) of this section does not apply, you must calculate rod packing vent emissions from each reciprocating compressor using equation W-29E to this section. Reciprocating compressor rod packing emissions that are routed to a flare, combustion, or vapor recovery system are not required to be determined under this paragraph (p).

(11) You must calculate both CH4 and CO2 mass emissions from volumetric emissions using calculations in paragraph (v) of this section.

(2) You must indicate whether your facility contains any of the component types subject to or complying with § 98.233(q) that are listed in § 98.232(c)(21), (d)(7), (e)(7) or (8), (f)(5) through (8), (g)(4), (g)(6) or (7), (h)(5), (h)(7) or (8), (i)(1), (j)(10), (m)(3)(ii) or (m)(4)(ii) for your facility's industry segment. For each component type and leak detection method combination that is located at your well-pad site, gathering and boosting site, or facility, you must report the information specified in paragraphs (q)(2)(i) through (ix) of this section. If a component type is located at your well-pad site, gathering and boosting site, or facility and no leaks were identified from that component, then you must report the information in paragraphs (q)(2)(i) through (ix) of this section but report a zero (“0”) for the information required according to paragraphs (q)(2)(vi) through (ix) of this section. If you used Calculation Method 1 (leaker factor emission calculation methodology) for some complete leak surveys and used Calculation Method 2 (leaker measurement methodology) for some complete leak surveys, you must report the information specified in paragraphs (q)(2)(i) through (ix) of this section separately for component surveys using Calculation Method 1 and Calculation Method 2.

(i) Well-pad ID (for the onshore petroleum and natural gas production industry segment only) or gathering and boosting site ID (for the onshore petroleum and natural gas gathering and boosting industry segment only).

(iii) Leak detection method used for the screening survey (e.g., Method 21 as specified in § 98.234(a)(2)(i); Method 21 as specified in § 98.234(a)(2)(ii); and OGI and other leak detection methods as specified in § 98.234(a)(1), (3), or (5)).

(iv) Emission factor or measurement method used (e.g., default emission factor; facility-specific emission factor developed according to § 98.233(q)(4); or direct measurement according to § 98.233(q)(3)).

(vi) Total number of the surveyed component types by leak detection method that were identified as leaking in the calendar year (“xp” in equation W-30 to § 98.233 for the component type or the number of leaks measured for the specified component type according to the provisions in § 98.233(q)(3)).

(vii) Average time the surveyed components are assumed to be leaking and operational, in hours (average of “Tp,z” from equation W-30 to § 98.233 for the component type or average duration of leaks for the specified component type determined according to the provisions in § 98.233(q)(3)(ii)).

(viii) Annual CO2 emissions, in metric tons CO2, for the component type as calculated using equation W-30 to § 98.233 or § 98.233(q)(3)(vii) (for surveyed components only).

(ix) Annual CH4 emissions, in metric tons CH4, for the component type as calculated using equation W-30 to § 98.233 or § 98.233(q)(3)(vii) (for surveyed components only).

(iii) For the components listed in § 98.232(c)(21)(i), (e)(7) and (8), (f)(5) through (8), (g)(4), (g)(6) and (7), (h)(5), (h)(7) and (8), and (j)(10)(i) that are subject to the well site or compressor station fugitive emissions standards in § 60.5397a of this chapter, the fugitive emissions standards for well sites, centralized production facilities, and compressor stations in § 60.5397b or 60.5398b of this chapter, or an applicable approved state plan or applicable Federal plan in part 62 of this chapter, and are required to conduct surveys using any of the leak detection methods in § 98.234(a)(1)(ii) or (iii) or (a)(2)(ii), as applicable, you must use the results of those surveys to calculate equipment leak emissions using the procedures specified in either paragraph (q)(2) or (3) of this section.

(r) This paragraph (r) applies to emissions sources listed in § 98.232(c)(21)(ii), (f)(7), (g)(5), (h)(6), (j)(10)(ii), (m)(3)(i), and (m)(4)(i) if you are not required to comply with paragraph (q) of this section and if you do not elect to comply with paragraph (q) of this section for these components in lieu of this paragraph (r). This paragraph (r) also applies to emission sources listed in § 98.232(i)(2) through (6), (j)(11), and (m)(5). To be subject to the requirements of this paragraph (r), the listed emissions sources also must contact streams with gas content greater than 10 percent CH4 plus CO2 by weight. Emissions sources that contact streams with gas content less than or equal to 10 percent CH4 plus CO2 by weight are exempt from the requirements of this paragraph (r) and do not need to be reported. Tubing systems equal to or less than one half inch diameter are exempt from the requirements of this paragraph (r) and do not need to be reported. Equipment leak components in vacuum service are exempt from the survey and emission estimation requirements of this paragraph (r) and only the count of these equipment must be reported. You must calculate emissions from all emission sources listed in this paragraph (r) using equation W-32A to this section, except for natural gas distribution facility emission sources listed in § 98.232(i)(3). Natural gas distribution facility emission sources listed in § 98.232(i)(3) must calculate emissions using equation W-32B to this section and according to paragraph (r)(6)(ii) of this section.

(1) Calculate both CH4 and CO2 mass emissions from volumetric emissions using calculations in paragraph (v) of this section.

(2) Onshore petroleum and natural gas production facilities and onshore petroleum and natural gas gathering and boosting facilities must use the appropriate default whole gas population emission factors listed in table W-1 to this subpart. Major equipment associated with gas wells are considered gas service equipment in table W-1 to this subpart. Onshore petroleum and natural gas gathering and boosting facilities shall use the gas service equipment emission factors in table W-1 to this subpart. Major equipment associated with crude oil wells are considered crude service equipment in table W-1 to this subpart. Where facilities conduct EOR operations, the emission factor listed in table W-1 to this subpart shall be used to estimate all streams of gases, including recycle CO2 stream. For meters/piping, use one meters/piping per well-pad for onshore petroleum and natural gas production operations and the number of meters in the facility for onshore petroleum and natural gas gathering and boosting operations.

(3) Underground natural gas storage facilities must use the appropriate default total hydrocarbon population emission factors for storage wellheads in gas service listed in table W-3 to this subpart.

(4) LNG storage facilities must use the appropriate default methane population emission factors for LNG storage compressors in gas service listed in table W-5 to this subpart.

(5) LNG import and export facilities must use the appropriate default methane population emission factors for LNG terminal compressors in gas service listed in table W-5 to this subpart.

(6) Natural gas distribution facilities must use the appropriate methane emission factors as described in paragraphs (r)(6)(i) and (ii) of this section.

(i) Below grade transmission-distribution transfer stations, below grade metering-regulating stations, distribution mains, and distribution services must use the appropriate default methane population emission factors listed in table W-5 to this subpart to estimate emissions from components listed in § 98.232(i)(2), (4), (5), and (6), respectively.

(ii) Above grade metering-regulating stations that are not above grade transmission-distribution transfer stations must use the meter/regulator run population emission factor calculated in equation W-31 to this section in accordance with paragraph (q)(2)(x) or (q)(3)(viii)(A) of this section for the components listed in § 98.232(i)(3). Natural gas distribution facilities that do not have above grade transmission-distribution transfer stations are not required to calculate emissions for above grade metering-regulating stations and are not required to report GHG emissions in § 98.236(r)(2)(v).

(7) Onshore natural gas transmission pipeline facilities must use the appropriate default methane population emission factors listed in table W-5 to this subpart to estimate emissions from components listed in § 98.232(m)(3)(i), (4)(i) and (5).

(r) This paragraph (r) applies to emissions sources listed in § 98.232(c)(21)(ii), (f)(7), (g)(5), (h)(6), (j)(10)(ii), (m)(3)(i), and (m)(4)(i) if you are not required to comply with paragraph (q) of this section and if you do not elect to comply with paragraph (q) of this section for these components in lieu of this paragraph (r). This paragraph (r) also applies to emission sources listed in § 98.232(i)(2) through (6), (j)(11), and (m)(5). To be subject to the requirements of this paragraph (r), the listed emissions sources also must contact streams with gas content greater than 10 percent CH4 plus CO2 by weight. Emissions sources that contact streams with gas content less than or equal to 10 percent CH4 plus CO2 by weight are exempt from the requirements of this paragraph (r) and do not need to be reported. Tubing systems equal to or less than one half inch diameter are exempt from the requirements of this paragraph (r) and do not need to be reported. Equipment leak components in vacuum service are exempt from the survey and emission estimation requirements of this paragraph (r) and only the count of these equipment must be reported. You must calculate emissions from all emission sources listed in this paragraph (r) using equation W-32A to this section, except for natural gas distribution facility emission sources listed in § 98.232(i)(3). Natural gas distribution facility emission sources listed in § 98.232(i)(3) must calculate emissions using equation W-32B to this section and according to paragraph (r)(6)(ii) of this section.

(1) Calculate both CH4 and CO2 mass emissions from volumetric emissions using calculations in paragraph (v) of this section.

(2) Onshore petroleum and natural gas production facilities and onshore petroleum and natural gas gathering and boosting facilities must use the appropriate default whole gas population emission factors listed in table W-1 to this subpart. Major equipment associated with gas wells are considered gas service equipment in table W-1 to this subpart. Onshore petroleum and natural gas gathering and boosting facilities shall use the gas service equipment emission factors in table W-1 to this subpart. Major equipment associated with crude oil wells are considered crude service equipment in table W-1 to this subpart. Where facilities conduct EOR operations, the emission factor listed in table W-1 to this subpart shall be used to estimate all streams of gases, including recycle CO2 stream. For meters/piping, use one meters/piping per well-pad for onshore petroleum and natural gas production operations and the number of meters in the facility for onshore petroleum and natural gas gathering and boosting operations.

(3) Underground natural gas storage facilities must use the appropriate default total hydrocarbon population emission factors for storage wellheads in gas service listed in table W-3 to this subpart.

(4) LNG storage facilities must use the appropriate default methane population emission factors for LNG storage compressors in gas service listed in table W-5 to this subpart.

(5) LNG import and export facilities must use the appropriate default methane population emission factors for LNG terminal compressors in gas service listed in table W-5 to this subpart.

(6) Natural gas distribution facilities must use the appropriate methane emission factors as described in paragraphs (r)(6)(i) and (ii) of this section.

(i) Below grade transmission-distribution transfer stations, below grade metering-regulating stations, distribution mains, and distribution services must use the appropriate default methane population emission factors listed in table W-5 to this subpart to estimate emissions from components listed in § 98.232(i)(2), (4), (5), and (6), respectively.

(ii) Above grade metering-regulating stations that are not above grade transmission-distribution transfer stations must use the meter/regulator run population emission factor calculated in equation W-31 to this section in accordance with paragraph (q)(2)(x) or (q)(3)(viii)(A) of this section for the components listed in § 98.232(i)(3). Natural gas distribution facilities that do not have above grade transmission-distribution transfer stations are not required to calculate emissions for above grade metering-regulating stations and are not required to report GHG emissions in § 98.236(r)(2)(v).

(7) Onshore natural gas transmission pipeline facilities must use the appropriate default methane population emission factors listed in table W-5 to this subpart to estimate emissions from components listed in § 98.232(m)(3)(i), (4)(i) and (5).

(z) If your facility is required by § 98.232(c)(22), (i)(7), or (j)(12) to report emissions from combustion equipment, then you must indicate whether your facility has any combustion units subject to reporting according to paragraph (a)(1)(xx), (a)(8)(vi), or (a)(9)(xiii) of this section. If your facility contains any combustion units subject to reporting according to paragraph (a)(1)(xx), (a)(8)(vi), or (a)(9)(xiii) of this section, then you must report the information specified in paragraphs (z)(1) and (2) of this section, as applicable. You must report the information specified in paragraphs (z)(1) and (2) of this section, as applicable, for each well-pad site (for onshore petroleum and natural gas production), gathering and boosting site (for onshore petroleum and natural gas gathering and boosting), or facility (for all other applicable industry segments).

(1) External fuel combustion units with a rated heat capacity less than or equal to 5 million Btu per hour; or, internal fuel combustion units that are not compressor-drivers, with a rated heat capacity less than or equal to 1 mmBtu/hr (or the equivalent of 130 horsepower). If the facility contains external fuel combustion units with a rated heat capacity less than or equal to 5 million Btu per hour or internal fuel combustion units that are not compressor-drivers, with a rated heat capacity less than or equal to 1 million Btu per hour (or the equivalent of 130 horsepower), then you must report the information specified in paragraphs (z)(1)(i) through (iii) of this section for each unit type.

(i) Well-pad ID (for the onshore petroleum and natural gas production industry segment only) or gathering and boosting site ID (for the onshore petroleum and natural gas gathering and boosting industry segment only).

(2) External fuel combustion units with a rated heat capacity greater than 5 million Btu per hour; internal fuel combustion units that are not compressor-drivers, with a rated heat capacity greater than 1 million Btu per hour (or the equivalent of 130 horsepower); or, internal fuel combustion units of any heat capacity that are compressor-drivers. For each type of combustion unit at your facility, you must report the information specified in paragraphs (z)(2)(i) through (iv) and (z)(2)(viii) through (x) of this section, except for internal fuel combustion units that are not compressor-drivers, with a rated heat capacity greater than 1 million Btu per hour (or the equivalent of 130 horsepower) or internal fuel combustion units of any heat capacity that are compressor-drivers that combust natural gas meeting the criteria in § 98.233(z)(1) or (2) or a fuel meeting the criteria in § 98.233(z)(3), which must report the information specified in paragraphs (z)(2)(i) through (x) of this section. Information must be reported for each combustion unit type, fuel type, and method for determining the CH4 emission factor combination, as applicable.

(i) Well-pad ID (for the onshore petroleum and natural gas production industry segment only) or gathering and boosting site ID (for the onshore petroleum and natural gas gathering and boosting industry segment only).

(ii) The type of combustion unit including external fuel combustion units with a rated heat capacity greater than 5 million Btu per hour; internal fuel combustion units that are not compressor-drivers, with a rated heat capacity greater than 1 million Btu per hour (or the equivalent of 130 horsepower); or internal fuel combustion units of any heat capacity that are compressor-drivers.

(iv) The quantity of fuel combusted in the calendar year, in thousand standard cubic feet, gallons, or tons.

(v) The equipment type, including reciprocating 2-stroke-lean burn, reciprocating 4-stroke lean-burn, reciprocating 4-stroke rich-burn, and gas turbine.

(vi) The method used to determine the methane emission factor, including the default emission factor from table W-7 to this subpart, OEM data, or performance tests in § 98.234(i) for natural gas described in § 98.233(z)(1) or (2), or performance tests in § 98.234(i) or default combustion efficiency for fuels described in section § 98.233(z)(3).

(vii) If multiple performance tests were performed in the same reporting year, the arithmetic average value of CH4 emission factor (kg CH4/mmBtu). This information is not required if CH4 emissions were calculated per § 98.233(z)(3)(ii)(D).

(viii) Annual CO2 emissions, in metric tons CO2, calculated according to § 98.233(z)(1) through (3).

(ix) Annual CH4 emissions, in metric tons CH4, calculated according to § 98.233(z)(1) through (3).

(x) Annual N2O emissions, in metric tons N2O, calculated according to § 98.233(z)(1) through (3).

Except as provided in this section, all terms used in this subpart have the same meaning given in the Clean Air Act and subpart A of this part.

(4) Facilities must report emissions from the onshore natural gas transmission pipeline industry segment only if emission sources specified in § 98.232(m) emit 25,000 metric tons of CO2 equivalent or more per year.

(1) If the entire facility is acquired by an owner or operator that does not already have a reporting facility in the same industry segment and basin (for onshore petroleum and natural gas production or onshore petroleum and natural gas gathering and boosting) or state (for natural gas distribution), then within 90 days after the change in the owner or operator, the designated representative or any alternate designated representative shall submit a certificate of representation that is complete under this section. If the new owner or operator already had emission sources specified in § 98.232(c), (i), (j), or (m), as applicable, prior to the acquisition in the same basin (for onshore petroleum and natural gas production or onshore petroleum and natural gas gathering and boosting) or state (for natural gas distribution) as the acquired facility but had not previously met the applicability requirements in §§ 98.2(a) and 98.231, then per the applicable definition of facility in § 98.238, the previously owned applicable emission sources must be included in the acquired facility. The new owner or operator and the new designated representative shall be responsible for submitting the annual report for the facility for the entire reporting year beginning with the reporting year in which the acquisition occurred.

(r) This paragraph (r) applies to emissions sources listed in § 98.232(c)(21)(ii), (f)(7), (g)(5), (h)(6), (j)(10)(ii), (m)(3)(i), and (m)(4)(i) if you are not required to comply with paragraph (q) of this section and if you do not elect to comply with paragraph (q) of this section for these components in lieu of this paragraph (r). This paragraph (r) also applies to emission sources listed in § 98.232(i)(2) through (6), (j)(11), and (m)(5). To be subject to the requirements of this paragraph (r), the listed emissions sources also must contact streams with gas content greater than 10 percent CH4 plus CO2 by weight. Emissions sources that contact streams with gas content less than or equal to 10 percent CH4 plus CO2 by weight are exempt from the requirements of this paragraph (r) and do not need to be reported. Tubing systems equal to or less than one half inch diameter are exempt from the requirements of this paragraph (r) and do not need to be reported. Equipment leak components in vacuum service are exempt from the survey and emission estimation requirements of this paragraph (r) and only the count of these equipment must be reported. You must calculate emissions from all emission sources listed in this paragraph (r) using equation W-32A to this section, except for natural gas distribution facility emission sources listed in § 98.232(i)(3). Natural gas distribution facility emission sources listed in § 98.232(i)(3) must calculate emissions using equation W-32B to this section and according to paragraph (r)(6)(ii) of this section.

(1) Calculate both CH4 and CO2 mass emissions from volumetric emissions using calculations in paragraph (v) of this section.

(2) Onshore petroleum and natural gas production facilities and onshore petroleum and natural gas gathering and boosting facilities must use the appropriate default whole gas population emission factors listed in table W-1 to this subpart. Major equipment associated with gas wells are considered gas service equipment in table W-1 to this subpart. Onshore petroleum and natural gas gathering and boosting facilities shall use the gas service equipment emission factors in table W-1 to this subpart. Major equipment associated with crude oil wells are considered crude service equipment in table W-1 to this subpart. Where facilities conduct EOR operations, the emission factor listed in table W-1 to this subpart shall be used to estimate all streams of gases, including recycle CO2 stream. For meters/piping, use one meters/piping per well-pad for onshore petroleum and natural gas production operations and the number of meters in the facility for onshore petroleum and natural gas gathering and boosting operations.

(3) Underground natural gas storage facilities must use the appropriate default total hydrocarbon population emission factors for storage wellheads in gas service listed in table W-3 to this subpart.

(4) LNG storage facilities must use the appropriate default methane population emission factors for LNG storage compressors in gas service listed in table W-5 to this subpart.

(5) LNG import and export facilities must use the appropriate default methane population emission factors for LNG terminal compressors in gas service listed in table W-5 to this subpart.

(6) Natural gas distribution facilities must use the appropriate methane emission factors as described in paragraphs (r)(6)(i) and (ii) of this section.

(i) Below grade transmission-distribution transfer stations, below grade metering-regulating stations, distribution mains, and distribution services must use the appropriate default methane population emission factors listed in table W-5 to this subpart to estimate emissions from components listed in § 98.232(i)(2), (4), (5), and (6), respectively.

(ii) Above grade metering-regulating stations that are not above grade transmission-distribution transfer stations must use the meter/regulator run population emission factor calculated in equation W-31 to this section in accordance with paragraph (q)(2)(x) or (q)(3)(viii)(A) of this section for the components listed in § 98.232(i)(3). Natural gas distribution facilities that do not have above grade transmission-distribution transfer stations are not required to calculate emissions for above grade metering-regulating stations and are not required to report GHG emissions in § 98.236(r)(2)(v).

(7) Onshore natural gas transmission pipeline facilities must use the appropriate default methane population emission factors listed in table W-5 to this subpart to estimate emissions from components listed in § 98.232(m)(3)(i), (4)(i) and (5).

(vi) For the components listed in § 98.232(m)(3)(ii) and (m)(4)(ii), you may elect to conduct surveys according to this paragraph (q), and, if you elect to do so, then you must use one of the leak detection methods in § 98.234(a). If you elect to use a leak detection method in § 98.234(a) for the surveyed component types in § 98.232(m)(3)(ii) and (m)(4)(ii) in lieu of the population count methodology specified in paragraph (r) of this section, then you must calculate emissions for the surveyed component types in § 98.232(m)(3)(ii) and (m)(4)(ii) using the procedures in either paragraph (q)(2) or (3) of this section.