Citations — 40 C.F.R. § 53.51 — Demonstration of compliance with design specifications and manufacturing and test requirements.

Citations to 40 U.S.C. § 53.51 as a whole

40 C.F.R. § 53.2(a)(3)

Go to provision →

(3) 2.5. A FRM for measuring PM 2.5 must be a manual method that meets all requirements specified in appendix L of part 50 of this chapter and must include a PM 2.5 sampler that has been shown in accordance with this part to meet the applicable requirements specified in this subpart A and subpart E of this part. Further, FRM samplers must be manufactured in an ISO 9001-registered facility, as defined in § 53.1 and as set forth in § 53.51.
40 C.F.R. § 53.3(a)(6)

Go to provision →

(6) All designated FEMs for PM 2.5 or PM 10-2.5 must be manufactured in an ISO 9001-registered facility, as defined in § 53.1 and as set forth in § 53.51.
40 C.F.R. § 53.50(b)

Go to provision →

(b) 2.5 methods—(1) Reference method. A sampler associated with a candidate reference method for PM 2.5 shall be subject to the provisions, specifications, and test procedures prescribed in §§ 53.51 through 53.58.

(2) A sampler associated with a candidate Class I equivalent method for PM 2.5 shall be subject to the provisions, specifications, and test procedures prescribed in all sections of this subpart.

(3) A sampler associated with a candidate Class II equivalent method for PM 2.5 shall be subject to the provisions, specifications, and test procedures prescribed in all applicable sections of this subpart, as specified in subpart F of this part or as specified in § 53.3(a)(3).

40 C.F.R. § 53.51(a)(1)

Go to provision →

(1) Paragraphs (a) through (f) of this section specify certain documentation that must be submitted and tests that are required to demonstrate that samplers associated with a designated FRM or FEM for PM 2.5 or PM 10-2.5 are properly manufactured to meet all applicable design and performance specifications and have been properly tested according to all applicable test requirements for such designation. Documentation is required to show that instruments and components of a PM 2.5 or PM 10-2.5 sampler are manufactured in an ISO 9001-registered facility under a quality system that meets ISO-9001 requirements for manufacturing quality control and testing.

40 C.F.R. § 53.51(a)(1)

Go to provision →

(1) Paragraphs (a) through (f) of this section specify certain documentation that must be submitted and tests that are required to demonstrate that samplers associated with a designated FRM or FEM for PM 2.5 or PM 10-2.5 are properly manufactured to meet all applicable design and performance specifications and have been properly tested according to all applicable test requirements for such designation. Documentation is required to show that instruments and components of a PM 2.5 or PM 10-2.5 sampler are manufactured in an ISO 9001-registered facility under a quality system that meets ISO-9001 requirements for manufacturing quality control and testing.

40 C.F.R. § 53.51(a)(1)

Go to provision →

(1) Paragraphs (a) through (f) of this section specify certain documentation that must be submitted and tests that are required to demonstrate that samplers associated with a designated FRM or FEM for PM 2.5 or PM 10-2.5 are properly manufactured to meet all applicable design and performance specifications and have been properly tested according to all applicable test requirements for such designation. Documentation is required to show that instruments and components of a PM 2.5 or PM 10-2.5 sampler are manufactured in an ISO 9001-registered facility under a quality system that meets ISO-9001 requirements for manufacturing quality control and testing.

40 C.F.R. § 53.51(a)(1)

Go to provision →

(1) Paragraphs (a) through (f) of this section specify certain documentation that must be submitted and tests that are required to demonstrate that samplers associated with a designated FRM or FEM for PM 2.5 or PM 10-2.5 are properly manufactured to meet all applicable design and performance specifications and have been properly tested according to all applicable test requirements for such designation. Documentation is required to show that instruments and components of a PM 2.5 or PM 10-2.5 sampler are manufactured in an ISO 9001-registered facility under a quality system that meets ISO-9001 requirements for manufacturing quality control and testing.

40 C.F.R. § 53.51(a)(1)

Go to provision →

(1) Paragraphs (a) through (f) of this section specify certain documentation that must be submitted and tests that are required to demonstrate that samplers associated with a designated FRM or FEM for PM 2.5 or PM 10-2.5 are properly manufactured to meet all applicable design and performance specifications and have been properly tested according to all applicable test requirements for such designation. Documentation is required to show that instruments and components of a PM 2.5 or PM 10-2.5 sampler are manufactured in an ISO 9001-registered facility under a quality system that meets ISO-9001 requirements for manufacturing quality control and testing.

40 C.F.R. § 53.51(a)(1)

Go to provision →

(1) Paragraphs (a) through (f) of this section specify certain documentation that must be submitted and tests that are required to demonstrate that samplers associated with a designated FRM or FEM for PM 2.5 or PM 10-2.5 are properly manufactured to meet all applicable design and performance specifications and have been properly tested according to all applicable test requirements for such designation. Documentation is required to show that instruments and components of a PM 2.5 or PM 10-2.5 sampler are manufactured in an ISO 9001-registered facility under a quality system that meets ISO-9001 requirements for manufacturing quality control and testing.