§49.154. Permit application requirements. — Inbound Citations

(a) As set forth in this Federal Implementation Plan (FIP), the Federal minor NSR program in Indian country (or “program”) consists of §§ 49.151 through 49.165.

(9) Any source eligible to request coverage under a general permit may request to be excluded from the general permit by applying for a permit under § 49.154.

You may obtain a synthetic minor source permit under this program to establish a synthetic minor source for purposes of the applicable PSD, nonattainment major NSR or Clean Air Act title V program and/or a synthetic minor HAP source for purposes of part 63 of the Act or the applicable Clean Air Act title V program. Any source that becomes a synthetic minor source for NSR and title V purposes but has other applicable requirements or becomes a synthetic minor for NSR but is major for title V purposes, remains subject to the applicable title V program. Note that if you propose to construct or modify a synthetic minor source, you are also subject to the preconstruction permitting requirements in §§ 49.154 and 49.155, except for the permit application content and permit application completeness provisions included in § 49.154(a)(2) and § 49.154(b).

(c) If you propose to establish a synthetic minor source or synthetic minor HAP source or to construct a minor modification at your major source, you will have to comply with the requirements of the Federal minor NSR program in Indian country at §§ 49.151 through 49.165 or other EPA-approved minor NSR program, as applicable.

(vi) Tribal Minor NSR permits issued under 40 CFR 49.151 through 49.161.

(1) You must submit a permit application that meets the requirements of § 49.154(a).

(a) Paragraphs (a)(1) through (3) of this section govern the content of your application.

(1) The following provisions apply to permit applications under this program:

(i) The reviewing authority may develop permit application forms for your use.

(ii) The permit application need not contain information on the exempt emissions units and activities listed in § 49.153(c).

(iii) The permit application for a modification need only include information on the affected emissions units as defined in § 49.152(d).

(2) Except as specified in paragraphs (a)(1)(ii) and (iii) of this section, you must include the information listed in paragraphs (a)(2)(i) through (ix) of this section in your application for a permit under this program. The reviewing authority may require additional information as needed to process the permit application.

(i) Identifying information, including your name and address (and plant name and address if different) and the name and telephone number of the plant manager/contact.

(iii) A list of all affected emissions units (with the exception of the exempt emissions units and activities listed in § 49.153(c)).

(iv) For each new emissions unit that is listed, the potential to emit of each regulated NSR pollutant in tpy (including fugitive emissions, to the extent that they are quantifiable, if the emissions unit or source is in one of the source categories listed in part 51, Appendix S, paragraph II.A.4(iii) or § 52.21(b)(1)(iii) of this chapter, as applicable), with supporting documentation. In your calculation of the potential to emit for an emissions unit, you must account for any proposed emission limitations.

(v) For each modified emissions unit and replacement unit that is listed, the allowable emissions of each regulated NSR pollutant in tpy both before and after the modification (including fugitive emissions, to the extent that they are quantifiable, if the emissions unit or source belongs to one of the source categories listed in part 51, Appendix S, paragraph II.A.4(iii) or § 52.21(b)(1)(iii) of this chapter, as applicable), with supporting documentation. For emissions units that do not have an allowable emissions limit prior to the modification, report the potential to emit. In your calculation of annual allowable emissions for an emissions unit after the modification, you must account for any proposed emission limitations.

(vi) Fuels, fuel use, raw materials, production rates and operating schedules.

(vii) Identification and description of any existing air pollution control equipment and compliance monitoring devices or activities.

(viii) Any existing limitations on source operation affecting emissions or any work practice standards, where applicable, for all NSR regulated pollutants at the source.

(ix) For each emission point associated with an affected emissions unit, provide stack or vent dimensions and flow information.

(3) At your option, you may propose emission limitations for each affected emissions unit, which may include pollution prevention techniques, air pollution control devices, design standards, equipment standards, work practices, operational standards or a combination thereof. You may include an explanation of why you believe the proposed emission limitations to be appropriate.

(a) Paragraphs (a)(1) through (3) of this section govern the content of your application.

(1) The following provisions apply to permit applications under this program:

(i) The reviewing authority may develop permit application forms for your use.

(ii) The permit application need not contain information on the exempt emissions units and activities listed in § 49.153(c).

(iii) The permit application for a modification need only include information on the affected emissions units as defined in § 49.152(d).

(2) Except as specified in paragraphs (a)(1)(ii) and (iii) of this section, you must include the information listed in paragraphs (a)(2)(i) through (ix) of this section in your application for a permit under this program. The reviewing authority may require additional information as needed to process the permit application.

(i) Identifying information, including your name and address (and plant name and address if different) and the name and telephone number of the plant manager/contact.

(iii) A list of all affected emissions units (with the exception of the exempt emissions units and activities listed in § 49.153(c)).

(iv) For each new emissions unit that is listed, the potential to emit of each regulated NSR pollutant in tpy (including fugitive emissions, to the extent that they are quantifiable, if the emissions unit or source is in one of the source categories listed in part 51, Appendix S, paragraph II.A.4(iii) or § 52.21(b)(1)(iii) of this chapter, as applicable), with supporting documentation. In your calculation of the potential to emit for an emissions unit, you must account for any proposed emission limitations.

(v) For each modified emissions unit and replacement unit that is listed, the allowable emissions of each regulated NSR pollutant in tpy both before and after the modification (including fugitive emissions, to the extent that they are quantifiable, if the emissions unit or source belongs to one of the source categories listed in part 51, Appendix S, paragraph II.A.4(iii) or § 52.21(b)(1)(iii) of this chapter, as applicable), with supporting documentation. For emissions units that do not have an allowable emissions limit prior to the modification, report the potential to emit. In your calculation of annual allowable emissions for an emissions unit after the modification, you must account for any proposed emission limitations.

(vi) Fuels, fuel use, raw materials, production rates and operating schedules.

(vii) Identification and description of any existing air pollution control equipment and compliance monitoring devices or activities.

(viii) Any existing limitations on source operation affecting emissions or any work practice standards, where applicable, for all NSR regulated pollutants at the source.

(ix) For each emission point associated with an affected emissions unit, provide stack or vent dimensions and flow information.

(3) At your option, you may propose emission limitations for each affected emissions unit, which may include pollution prevention techniques, air pollution control devices, design standards, equipment standards, work practices, operational standards or a combination thereof. You may include an explanation of why you believe the proposed emission limitations to be appropriate.

You may obtain a synthetic minor source permit under this program to establish a synthetic minor source for purposes of the applicable PSD, nonattainment major NSR or Clean Air Act title V program and/or a synthetic minor HAP source for purposes of part 63 of the Act or the applicable Clean Air Act title V program. Any source that becomes a synthetic minor source for NSR and title V purposes but has other applicable requirements or becomes a synthetic minor for NSR but is major for title V purposes, remains subject to the applicable title V program. Note that if you propose to construct or modify a synthetic minor source, you are also subject to the preconstruction permitting requirements in §§ 49.154 and 49.155, except for the permit application content and permit application completeness provisions included in § 49.154(a)(2) and § 49.154(b).

(2) Except as specified in paragraphs (a)(1)(ii) and (iii) of this section, you must include the information listed in paragraphs (a)(2)(i) through (ix) of this section in your application for a permit under this program. The reviewing authority may require additional information as needed to process the permit application.

(i) Identifying information, including your name and address (and plant name and address if different) and the name and telephone number of the plant manager/contact.

(iii) A list of all affected emissions units (with the exception of the exempt emissions units and activities listed in § 49.153(c)).

(iv) For each new emissions unit that is listed, the potential to emit of each regulated NSR pollutant in tpy (including fugitive emissions, to the extent that they are quantifiable, if the emissions unit or source is in one of the source categories listed in part 51, Appendix S, paragraph II.A.4(iii) or § 52.21(b)(1)(iii) of this chapter, as applicable), with supporting documentation. In your calculation of the potential to emit for an emissions unit, you must account for any proposed emission limitations.

(v) For each modified emissions unit and replacement unit that is listed, the allowable emissions of each regulated NSR pollutant in tpy both before and after the modification (including fugitive emissions, to the extent that they are quantifiable, if the emissions unit or source belongs to one of the source categories listed in part 51, Appendix S, paragraph II.A.4(iii) or § 52.21(b)(1)(iii) of this chapter, as applicable), with supporting documentation. For emissions units that do not have an allowable emissions limit prior to the modification, report the potential to emit. In your calculation of annual allowable emissions for an emissions unit after the modification, you must account for any proposed emission limitations.

(vi) Fuels, fuel use, raw materials, production rates and operating schedules.

(vii) Identification and description of any existing air pollution control equipment and compliance monitoring devices or activities.

(viii) Any existing limitations on source operation affecting emissions or any work practice standards, where applicable, for all NSR regulated pollutants at the source.

(ix) For each emission point associated with an affected emissions unit, provide stack or vent dimensions and flow information.

(2) Except as specified in paragraphs (a)(1)(ii) and (iii) of this section, you must include the information listed in paragraphs (a)(2)(i) through (ix) of this section in your application for a permit under this program. The reviewing authority may require additional information as needed to process the permit application.

(i) Identifying information, including your name and address (and plant name and address if different) and the name and telephone number of the plant manager/contact.

(iii) A list of all affected emissions units (with the exception of the exempt emissions units and activities listed in § 49.153(c)).

(iv) For each new emissions unit that is listed, the potential to emit of each regulated NSR pollutant in tpy (including fugitive emissions, to the extent that they are quantifiable, if the emissions unit or source is in one of the source categories listed in part 51, Appendix S, paragraph II.A.4(iii) or § 52.21(b)(1)(iii) of this chapter, as applicable), with supporting documentation. In your calculation of the potential to emit for an emissions unit, you must account for any proposed emission limitations.

(v) For each modified emissions unit and replacement unit that is listed, the allowable emissions of each regulated NSR pollutant in tpy both before and after the modification (including fugitive emissions, to the extent that they are quantifiable, if the emissions unit or source belongs to one of the source categories listed in part 51, Appendix S, paragraph II.A.4(iii) or § 52.21(b)(1)(iii) of this chapter, as applicable), with supporting documentation. For emissions units that do not have an allowable emissions limit prior to the modification, report the potential to emit. In your calculation of annual allowable emissions for an emissions unit after the modification, you must account for any proposed emission limitations.

(vi) Fuels, fuel use, raw materials, production rates and operating schedules.

(vii) Identification and description of any existing air pollution control equipment and compliance monitoring devices or activities.

(viii) Any existing limitations on source operation affecting emissions or any work practice standards, where applicable, for all NSR regulated pollutants at the source.

(ix) For each emission point associated with an affected emissions unit, provide stack or vent dimensions and flow information.

(2) Except as specified in paragraphs (a)(1)(ii) and (iii) of this section, you must include the information listed in paragraphs (a)(2)(i) through (ix) of this section in your application for a permit under this program. The reviewing authority may require additional information as needed to process the permit application.

(i) Identifying information, including your name and address (and plant name and address if different) and the name and telephone number of the plant manager/contact.

(iii) A list of all affected emissions units (with the exception of the exempt emissions units and activities listed in § 49.153(c)).

(iv) For each new emissions unit that is listed, the potential to emit of each regulated NSR pollutant in tpy (including fugitive emissions, to the extent that they are quantifiable, if the emissions unit or source is in one of the source categories listed in part 51, Appendix S, paragraph II.A.4(iii) or § 52.21(b)(1)(iii) of this chapter, as applicable), with supporting documentation. In your calculation of the potential to emit for an emissions unit, you must account for any proposed emission limitations.

(v) For each modified emissions unit and replacement unit that is listed, the allowable emissions of each regulated NSR pollutant in tpy both before and after the modification (including fugitive emissions, to the extent that they are quantifiable, if the emissions unit or source belongs to one of the source categories listed in part 51, Appendix S, paragraph II.A.4(iii) or § 52.21(b)(1)(iii) of this chapter, as applicable), with supporting documentation. For emissions units that do not have an allowable emissions limit prior to the modification, report the potential to emit. In your calculation of annual allowable emissions for an emissions unit after the modification, you must account for any proposed emission limitations.

(vi) Fuels, fuel use, raw materials, production rates and operating schedules.

(vii) Identification and description of any existing air pollution control equipment and compliance monitoring devices or activities.

(viii) Any existing limitations on source operation affecting emissions or any work practice standards, where applicable, for all NSR regulated pollutants at the source.

(ix) For each emission point associated with an affected emissions unit, provide stack or vent dimensions and flow information.

(2) Except as specified in paragraphs (a)(1)(ii) and (iii) of this section, you must include the information listed in paragraphs (a)(2)(i) through (ix) of this section in your application for a permit under this program. The reviewing authority may require additional information as needed to process the permit application.

(i) Identifying information, including your name and address (and plant name and address if different) and the name and telephone number of the plant manager/contact.

(iii) A list of all affected emissions units (with the exception of the exempt emissions units and activities listed in § 49.153(c)).

(iv) For each new emissions unit that is listed, the potential to emit of each regulated NSR pollutant in tpy (including fugitive emissions, to the extent that they are quantifiable, if the emissions unit or source is in one of the source categories listed in part 51, Appendix S, paragraph II.A.4(iii) or § 52.21(b)(1)(iii) of this chapter, as applicable), with supporting documentation. In your calculation of the potential to emit for an emissions unit, you must account for any proposed emission limitations.

(v) For each modified emissions unit and replacement unit that is listed, the allowable emissions of each regulated NSR pollutant in tpy both before and after the modification (including fugitive emissions, to the extent that they are quantifiable, if the emissions unit or source belongs to one of the source categories listed in part 51, Appendix S, paragraph II.A.4(iii) or § 52.21(b)(1)(iii) of this chapter, as applicable), with supporting documentation. For emissions units that do not have an allowable emissions limit prior to the modification, report the potential to emit. In your calculation of annual allowable emissions for an emissions unit after the modification, you must account for any proposed emission limitations.

(vi) Fuels, fuel use, raw materials, production rates and operating schedules.

(vii) Identification and description of any existing air pollution control equipment and compliance monitoring devices or activities.

(viii) Any existing limitations on source operation affecting emissions or any work practice standards, where applicable, for all NSR regulated pollutants at the source.

(ix) For each emission point associated with an affected emissions unit, provide stack or vent dimensions and flow information.

(2) Except as specified in paragraphs (a)(1)(ii) and (iii) of this section, you must include the information listed in paragraphs (a)(2)(i) through (ix) of this section in your application for a permit under this program. The reviewing authority may require additional information as needed to process the permit application.

(i) Identifying information, including your name and address (and plant name and address if different) and the name and telephone number of the plant manager/contact.

(iii) A list of all affected emissions units (with the exception of the exempt emissions units and activities listed in § 49.153(c)).

(iv) For each new emissions unit that is listed, the potential to emit of each regulated NSR pollutant in tpy (including fugitive emissions, to the extent that they are quantifiable, if the emissions unit or source is in one of the source categories listed in part 51, Appendix S, paragraph II.A.4(iii) or § 52.21(b)(1)(iii) of this chapter, as applicable), with supporting documentation. In your calculation of the potential to emit for an emissions unit, you must account for any proposed emission limitations.

(v) For each modified emissions unit and replacement unit that is listed, the allowable emissions of each regulated NSR pollutant in tpy both before and after the modification (including fugitive emissions, to the extent that they are quantifiable, if the emissions unit or source belongs to one of the source categories listed in part 51, Appendix S, paragraph II.A.4(iii) or § 52.21(b)(1)(iii) of this chapter, as applicable), with supporting documentation. For emissions units that do not have an allowable emissions limit prior to the modification, report the potential to emit. In your calculation of annual allowable emissions for an emissions unit after the modification, you must account for any proposed emission limitations.

(vi) Fuels, fuel use, raw materials, production rates and operating schedules.

(vii) Identification and description of any existing air pollution control equipment and compliance monitoring devices or activities.

(viii) Any existing limitations on source operation affecting emissions or any work practice standards, where applicable, for all NSR regulated pollutants at the source.

(ix) For each emission point associated with an affected emissions unit, provide stack or vent dimensions and flow information.

(2) Except as specified in paragraphs (a)(1)(ii) and (iii) of this section, you must include the information listed in paragraphs (a)(2)(i) through (ix) of this section in your application for a permit under this program. The reviewing authority may require additional information as needed to process the permit application.

(i) Identifying information, including your name and address (and plant name and address if different) and the name and telephone number of the plant manager/contact.

(iii) A list of all affected emissions units (with the exception of the exempt emissions units and activities listed in § 49.153(c)).

(iv) For each new emissions unit that is listed, the potential to emit of each regulated NSR pollutant in tpy (including fugitive emissions, to the extent that they are quantifiable, if the emissions unit or source is in one of the source categories listed in part 51, Appendix S, paragraph II.A.4(iii) or § 52.21(b)(1)(iii) of this chapter, as applicable), with supporting documentation. In your calculation of the potential to emit for an emissions unit, you must account for any proposed emission limitations.

(v) For each modified emissions unit and replacement unit that is listed, the allowable emissions of each regulated NSR pollutant in tpy both before and after the modification (including fugitive emissions, to the extent that they are quantifiable, if the emissions unit or source belongs to one of the source categories listed in part 51, Appendix S, paragraph II.A.4(iii) or § 52.21(b)(1)(iii) of this chapter, as applicable), with supporting documentation. For emissions units that do not have an allowable emissions limit prior to the modification, report the potential to emit. In your calculation of annual allowable emissions for an emissions unit after the modification, you must account for any proposed emission limitations.

(vi) Fuels, fuel use, raw materials, production rates and operating schedules.

(vii) Identification and description of any existing air pollution control equipment and compliance monitoring devices or activities.

(viii) Any existing limitations on source operation affecting emissions or any work practice standards, where applicable, for all NSR regulated pollutants at the source.

(ix) For each emission point associated with an affected emissions unit, provide stack or vent dimensions and flow information.

(2) Except as specified in paragraphs (a)(1)(ii) and (iii) of this section, you must include the information listed in paragraphs (a)(2)(i) through (ix) of this section in your application for a permit under this program. The reviewing authority may require additional information as needed to process the permit application.

(i) Identifying information, including your name and address (and plant name and address if different) and the name and telephone number of the plant manager/contact.

(iii) A list of all affected emissions units (with the exception of the exempt emissions units and activities listed in § 49.153(c)).

(iv) For each new emissions unit that is listed, the potential to emit of each regulated NSR pollutant in tpy (including fugitive emissions, to the extent that they are quantifiable, if the emissions unit or source is in one of the source categories listed in part 51, Appendix S, paragraph II.A.4(iii) or § 52.21(b)(1)(iii) of this chapter, as applicable), with supporting documentation. In your calculation of the potential to emit for an emissions unit, you must account for any proposed emission limitations.

(v) For each modified emissions unit and replacement unit that is listed, the allowable emissions of each regulated NSR pollutant in tpy both before and after the modification (including fugitive emissions, to the extent that they are quantifiable, if the emissions unit or source belongs to one of the source categories listed in part 51, Appendix S, paragraph II.A.4(iii) or § 52.21(b)(1)(iii) of this chapter, as applicable), with supporting documentation. For emissions units that do not have an allowable emissions limit prior to the modification, report the potential to emit. In your calculation of annual allowable emissions for an emissions unit after the modification, you must account for any proposed emission limitations.

(vi) Fuels, fuel use, raw materials, production rates and operating schedules.

(vii) Identification and description of any existing air pollution control equipment and compliance monitoring devices or activities.

(viii) Any existing limitations on source operation affecting emissions or any work practice standards, where applicable, for all NSR regulated pollutants at the source.

(ix) For each emission point associated with an affected emissions unit, provide stack or vent dimensions and flow information.

(2) Except as specified in paragraphs (a)(1)(ii) and (iii) of this section, you must include the information listed in paragraphs (a)(2)(i) through (ix) of this section in your application for a permit under this program. The reviewing authority may require additional information as needed to process the permit application.

(i) Identifying information, including your name and address (and plant name and address if different) and the name and telephone number of the plant manager/contact.

(iii) A list of all affected emissions units (with the exception of the exempt emissions units and activities listed in § 49.153(c)).

(iv) For each new emissions unit that is listed, the potential to emit of each regulated NSR pollutant in tpy (including fugitive emissions, to the extent that they are quantifiable, if the emissions unit or source is in one of the source categories listed in part 51, Appendix S, paragraph II.A.4(iii) or § 52.21(b)(1)(iii) of this chapter, as applicable), with supporting documentation. In your calculation of the potential to emit for an emissions unit, you must account for any proposed emission limitations.

(v) For each modified emissions unit and replacement unit that is listed, the allowable emissions of each regulated NSR pollutant in tpy both before and after the modification (including fugitive emissions, to the extent that they are quantifiable, if the emissions unit or source belongs to one of the source categories listed in part 51, Appendix S, paragraph II.A.4(iii) or § 52.21(b)(1)(iii) of this chapter, as applicable), with supporting documentation. For emissions units that do not have an allowable emissions limit prior to the modification, report the potential to emit. In your calculation of annual allowable emissions for an emissions unit after the modification, you must account for any proposed emission limitations.

(vi) Fuels, fuel use, raw materials, production rates and operating schedules.

(vii) Identification and description of any existing air pollution control equipment and compliance monitoring devices or activities.

(viii) Any existing limitations on source operation affecting emissions or any work practice standards, where applicable, for all NSR regulated pollutants at the source.

(ix) For each emission point associated with an affected emissions unit, provide stack or vent dimensions and flow information.

(2) Except as specified in paragraphs (a)(1)(ii) and (iii) of this section, you must include the information listed in paragraphs (a)(2)(i) through (ix) of this section in your application for a permit under this program. The reviewing authority may require additional information as needed to process the permit application.

(i) Identifying information, including your name and address (and plant name and address if different) and the name and telephone number of the plant manager/contact.

(iii) A list of all affected emissions units (with the exception of the exempt emissions units and activities listed in § 49.153(c)).

(iv) For each new emissions unit that is listed, the potential to emit of each regulated NSR pollutant in tpy (including fugitive emissions, to the extent that they are quantifiable, if the emissions unit or source is in one of the source categories listed in part 51, Appendix S, paragraph II.A.4(iii) or § 52.21(b)(1)(iii) of this chapter, as applicable), with supporting documentation. In your calculation of the potential to emit for an emissions unit, you must account for any proposed emission limitations.

(v) For each modified emissions unit and replacement unit that is listed, the allowable emissions of each regulated NSR pollutant in tpy both before and after the modification (including fugitive emissions, to the extent that they are quantifiable, if the emissions unit or source belongs to one of the source categories listed in part 51, Appendix S, paragraph II.A.4(iii) or § 52.21(b)(1)(iii) of this chapter, as applicable), with supporting documentation. For emissions units that do not have an allowable emissions limit prior to the modification, report the potential to emit. In your calculation of annual allowable emissions for an emissions unit after the modification, you must account for any proposed emission limitations.

(vi) Fuels, fuel use, raw materials, production rates and operating schedules.

(vii) Identification and description of any existing air pollution control equipment and compliance monitoring devices or activities.

(viii) Any existing limitations on source operation affecting emissions or any work practice standards, where applicable, for all NSR regulated pollutants at the source.

(ix) For each emission point associated with an affected emissions unit, provide stack or vent dimensions and flow information.

(a) Paragraphs (a)(1) through (3) of this section govern the content of your application.

(1) The following provisions apply to permit applications under this program:

(i) The reviewing authority may develop permit application forms for your use.

(ii) The permit application need not contain information on the exempt emissions units and activities listed in § 49.153(c).

(iii) The permit application for a modification need only include information on the affected emissions units as defined in § 49.152(d).

(2) Except as specified in paragraphs (a)(1)(ii) and (iii) of this section, you must include the information listed in paragraphs (a)(2)(i) through (ix) of this section in your application for a permit under this program. The reviewing authority may require additional information as needed to process the permit application.

(i) Identifying information, including your name and address (and plant name and address if different) and the name and telephone number of the plant manager/contact.

(iii) A list of all affected emissions units (with the exception of the exempt emissions units and activities listed in § 49.153(c)).

(iv) For each new emissions unit that is listed, the potential to emit of each regulated NSR pollutant in tpy (including fugitive emissions, to the extent that they are quantifiable, if the emissions unit or source is in one of the source categories listed in part 51, Appendix S, paragraph II.A.4(iii) or § 52.21(b)(1)(iii) of this chapter, as applicable), with supporting documentation. In your calculation of the potential to emit for an emissions unit, you must account for any proposed emission limitations.

(v) For each modified emissions unit and replacement unit that is listed, the allowable emissions of each regulated NSR pollutant in tpy both before and after the modification (including fugitive emissions, to the extent that they are quantifiable, if the emissions unit or source belongs to one of the source categories listed in part 51, Appendix S, paragraph II.A.4(iii) or § 52.21(b)(1)(iii) of this chapter, as applicable), with supporting documentation. For emissions units that do not have an allowable emissions limit prior to the modification, report the potential to emit. In your calculation of annual allowable emissions for an emissions unit after the modification, you must account for any proposed emission limitations.

(vi) Fuels, fuel use, raw materials, production rates and operating schedules.

(vii) Identification and description of any existing air pollution control equipment and compliance monitoring devices or activities.

(viii) Any existing limitations on source operation affecting emissions or any work practice standards, where applicable, for all NSR regulated pollutants at the source.

(ix) For each emission point associated with an affected emissions unit, provide stack or vent dimensions and flow information.

(3) At your option, you may propose emission limitations for each affected emissions unit, which may include pollution prevention techniques, air pollution control devices, design standards, equipment standards, work practices, operational standards or a combination thereof. You may include an explanation of why you believe the proposed emission limitations to be appropriate.

(2) The reviewing authority determines completeness of the permit application as provided in § 49.154(b) within 45 days of receiving the application (60 days for minor modifications at major sources).

You may obtain a synthetic minor source permit under this program to establish a synthetic minor source for purposes of the applicable PSD, nonattainment major NSR or Clean Air Act title V program and/or a synthetic minor HAP source for purposes of part 63 of the Act or the applicable Clean Air Act title V program. Any source that becomes a synthetic minor source for NSR and title V purposes but has other applicable requirements or becomes a synthetic minor for NSR but is major for title V purposes, remains subject to the applicable title V program. Note that if you propose to construct or modify a synthetic minor source, you are also subject to the preconstruction permitting requirements in §§ 49.154 and 49.155, except for the permit application content and permit application completeness provisions included in § 49.154(a)(2) and § 49.154(b).

(b) Paragraphs (b)(1) through (3) of this section govern the completeness review of your permit application.

(1) An application for a permit under this program will be reviewed by the reviewing authority within 45 days of its receipt (60 days for minor modifications at major sources) to determine whether the application contains all the information necessary for processing the application.

(2) If the reviewing authority determines that the application is not complete, it will request additional information from you as necessary to process the application. If the reviewing authority determines that the application is complete, it will notify you in writing. The reviewing authority's completeness determination or request for additional information should be postmarked within 45 days of receipt of the permit application by the reviewing authority (60 days for minor modifications at major sources). If you do not receive a request for additional information or a notice of complete application postmarked within 45 days of receipt of the permit application by the reviewing authority (60 days for minor modifications at major sources), your application will be deemed complete.

(3) If, while processing an application that has been determined to be complete, the reviewing authority determines that additional information is necessary to evaluate or take final action on the application, it may request additional information from you and require your responses within a reasonable time period.

(4) Any permit application will be granted or denied no later than 135 days (1 year for minor modifications at major sources) after the date the application is deemed complete and all additional information necessary to make an informed decision has been provided.

(b) Paragraphs (b)(1) through (3) of this section govern the completeness review of your permit application.

(1) An application for a permit under this program will be reviewed by the reviewing authority within 45 days of its receipt (60 days for minor modifications at major sources) to determine whether the application contains all the information necessary for processing the application.

(2) If the reviewing authority determines that the application is not complete, it will request additional information from you as necessary to process the application. If the reviewing authority determines that the application is complete, it will notify you in writing. The reviewing authority's completeness determination or request for additional information should be postmarked within 45 days of receipt of the permit application by the reviewing authority (60 days for minor modifications at major sources). If you do not receive a request for additional information or a notice of complete application postmarked within 45 days of receipt of the permit application by the reviewing authority (60 days for minor modifications at major sources), your application will be deemed complete.

(3) If, while processing an application that has been determined to be complete, the reviewing authority determines that additional information is necessary to evaluate or take final action on the application, it may request additional information from you and require your responses within a reasonable time period.

(4) Any permit application will be granted or denied no later than 135 days (1 year for minor modifications at major sources) after the date the application is deemed complete and all additional information necessary to make an informed decision has been provided.

(b) Paragraphs (b)(1) through (3) of this section govern the completeness review of your permit application.

(1) An application for a permit under this program will be reviewed by the reviewing authority within 45 days of its receipt (60 days for minor modifications at major sources) to determine whether the application contains all the information necessary for processing the application.

(2) If the reviewing authority determines that the application is not complete, it will request additional information from you as necessary to process the application. If the reviewing authority determines that the application is complete, it will notify you in writing. The reviewing authority's completeness determination or request for additional information should be postmarked within 45 days of receipt of the permit application by the reviewing authority (60 days for minor modifications at major sources). If you do not receive a request for additional information or a notice of complete application postmarked within 45 days of receipt of the permit application by the reviewing authority (60 days for minor modifications at major sources), your application will be deemed complete.

(3) If, while processing an application that has been determined to be complete, the reviewing authority determines that additional information is necessary to evaluate or take final action on the application, it may request additional information from you and require your responses within a reasonable time period.

(4) Any permit application will be granted or denied no later than 135 days (1 year for minor modifications at major sources) after the date the application is deemed complete and all additional information necessary to make an informed decision has been provided.

(3) The reviewing authority determines the appropriate emission limitations and permit conditions for your affected emissions units under § 49.154(c).

(2) The permit must include the emission limitations determined by the reviewing authority under § 49.154(c) for each affected emissions unit. In addition, the permit must include an annual allowable emissions limit for each affected emissions unit and for each regulated NSR pollutant emitted by the unit if the unit is issued an enforceable emission limitation lower than the potential to emit of that unit.

(2) A general permit must be issued according to the applicable requirements in § 49.154(c), § 49.154(d) and § 49.155, the public participation requirements in § 49.157 and the requirements for final permit issuance and administrative and judicial review in § 49.159.

(2) A general permit must be issued according to the applicable requirements in § 49.154(c), § 49.154(d) and § 49.155, the public participation requirements in § 49.157 and the requirements for final permit issuance and administrative and judicial review in § 49.159.

(d) Paragraphs (d)(1) through (3) of this section govern AQIA requirements under this program.

(1) If the reviewing authority has reason to be concerned that the construction of your minor source or modification would cause or contribute to a NAAQS or PSD increment violation, it may require you to conduct and submit an AQIA.

(2) If required, you must conduct the AQIA using the dispersion models and procedures of part 51, Appendix W of this chapter.

(3) If the AQIA reveals that construction of your source or modification would cause or contribute to a NAAQS or PSD increment violation, the reviewing authority must require you to reduce or mitigate such impacts before it can issue you a permit.

(d) Paragraphs (d)(1) through (3) of this section govern AQIA requirements under this program.

(1) If the reviewing authority has reason to be concerned that the construction of your minor source or modification would cause or contribute to a NAAQS or PSD increment violation, it may require you to conduct and submit an AQIA.

(2) If required, you must conduct the AQIA using the dispersion models and procedures of part 51, Appendix W of this chapter.

(3) If the AQIA reveals that construction of your source or modification would cause or contribute to a NAAQS or PSD increment violation, the reviewing authority must require you to reduce or mitigate such impacts before it can issue you a permit.

(d) Paragraphs (d)(1) through (3) of this section govern AQIA requirements under this program.

(1) If the reviewing authority has reason to be concerned that the construction of your minor source or modification would cause or contribute to a NAAQS or PSD increment violation, it may require you to conduct and submit an AQIA.

(2) If required, you must conduct the AQIA using the dispersion models and procedures of part 51, Appendix W of this chapter.

(3) If the AQIA reveals that construction of your source or modification would cause or contribute to a NAAQS or PSD increment violation, the reviewing authority must require you to reduce or mitigate such impacts before it can issue you a permit.