US Codex
C.F.R.
Browse by date

View an earlier version

Latest
Current
Browse all versions by date
Notes

29 C.F.R. §§ 1918.61–1918.66

6 sections in range

§1918.61. General (See also appendix IV of this part).

29 C.F.R. § 1918.61

(a)
Employer provided gear inspection. All gear and equipment provided by the employer shall be inspected by the employer or designated person before each use and, when appropriate, at intervals during its use, to ensure that it is safe. Any gear that is found upon such inspection to be unsafe shall not be used until it is made safe.
(b)
Safe working load.
(1)
The safe working load of gear as specified in §§ 1918.61 through 1918.66 shall not be exceeded.
(2)
All cargo handling gear provided by the employer with a safe working load greater than five short tons (10,000 lbs. or 4.54 metric tons) shall have its safe working load plainly marked on it.
(c)
Gear weight markings. The weight shall be plainly marked on any article of stevedoring gear hoisted by ship's gear and weighing more than 2,000 lbs. (.91 metric tons).
(d)
Certification. The employer shall not use any material handling device listed in paragraphs (f) and (g) of this section until the device has been certificated, as evidenced by current and valid documents attesting to compliance with the requirements of paragraph (e) of this section.
(e)
Certification procedures. Each certification required by this section shall be performed in accordance with part 1919 of this chapter, by a person then currently accredited by OSHA as provided in that part.
(f)
Special gear.
(1)
Special stevedoring gear provided by the employer, the strength of which depends upon components other than commonly used stock items such as shackles, ropes, or chains, and that has a Safe Working Load (SWL) greater than five short tons (10,000 lbs or 4.54 metric tons) shall be inspected and tested as a unit before initial use (see Table A in paragraph (f)(2) of this section). In addition, any special stevedoring gear that suffers damage necessitating structural repair shall be inspected and retested after repair and before being returned to service.
(2)
Special stevedoring gear provided by the employer that has a SWL of five short tons (10,000 lbs. or 4.54 metric tons) or less shall be inspected and tested as a unit before initial use according to paragraphs (d) and (e) of this section or by a designated person (see Table A in this paragraph (f)(2)).
(g)
Every spreader that is not a part of ship's gear and is used for handling intermodal containers shall be inspected and tested before initial use to a proof load equal to 25 percent greater than its rated capacity. In addition, any spreader that suffers damage necessitating structural repair shall be inspected and retested after repair and before being returned to service.
(h)
All cargo handling gear covered by this section with a SWL greater than five short tons (10,000 lbs. or 4.54 metric tons) shall be proof load tested according to Table A in paragraph (f) or paragraph (g), as applicable, of this section every four years and in accordance with paragraphs (d) and (e) of this section or by a designated person.
(i)
Certificates and inspection and test records attesting to the tests required by this section shall be available for inspection.
Notes, amendments, and revision history

Amendments

[62 FR 40202, July 25, 1997, as amended at 65 FR 40945, June 30, 2000]

Authority

Authority: 33 U.S.C. 941; 29 U.S.C. 653, 655, 657; Secretary of Labor's Order No. 12-71 (36 FR 8754), 8-76 (41 FR 25059), 9-83 (48 FR 35736), 1-90 (55 FR 9033), 6-96 (62 FR 111), 3-2000 (65 FR 50017), 5-2002 (67 FR 65008), 5-2007 (72 FR 31160), 4-2010 (75 FR 55355), 1-2012 (77 FR 3912), or 8-2020 (85 FR 58393), as applicable; and 29 CFR 1911. Sections 1918.90 and 1918.110 also issued under 5 U.S.C. 553. Section 1918.100 also issued under 49 U.S.C. 5101 et seq. and 5 U.S.C. 553.

Source

Source: 62 FR 40202, July 25, 1997, unless otherwise noted.

Amendments

[62 FR 40202, July 25, 1997, as amended at 65 FR 40945, June 30, 2000]

§1918.62. Miscellaneous auxiliary gear.

29 C.F.R. § 1918.62

(a)
Routine inspection.
(1)
At the completion of each use, loose gear such as slings, chains, bridles, blocks and hooks shall be so placed as to avoid damage to the gear. Loose gear shall be inspected and any defects corrected before reuse.
(2)
Defective gear, as defined by the manufacturers' specifications (when available), shall not be used. Distorted hooks, shackles or similar gear shall be discarded.
(b)
Wire rope and wire rope slings.
(1)
The employer shall follow the manufacturers' recommended ratings for wire rope and wire rope slings provided for use aboard ship, and shall have such ratings available for inspection. When the manufacturer is unable to supply such ratings, the employer shall use the tables for wire rope and wire rope slings found in appendix II to this part. A design safety factor of at least five shall be maintained for the common sizes of running wire used as falls in purchases, or in such uses as light load slings.
(2)
Wire rope with a safety factor of less than five may be used only as follows:
(i)
In specialized equipment, such as cranes, designed to be used with lesser wire rope safety factors;
(ii)
According to design factors in standing rigging applications; or
(iii)
For heavy lifts or other purposes for which a safety factor of five is not feasible and for which the employer can show that equivalent safety is ensured.
(3)
Wire rope or wire rope slings provided by the employer and having any of the following conditions shall not be used:
(i)
Ten randomly distributed broken wires in one rope lay or three or more broken wires in one strand in one rope lay;
(ii)
Kinking, crushing, bird caging or other damage resulting in distortion of the wire rope structure;
(iii)
Evidence of heat damage;
(iv)
Excessive wear or corrosion, deformation or other defect in the wire or attachments, including cracks in attachments;
(v)
Any indication of strand or wire slippage in end attachments; or
(vi)
More than one broken wire close to a socket or swaged fitting.
(4)
Protruding ends of strands in splices on slings and bridles shall be covered or blunted. Coverings shall be removable so that splices can be examined. Means used to cover or blunt ends shall not damage the wire.
(5)
Where wire rope clips are used to form eyes, the employer shall follow the manufacturers' recommendations, which shall be available for inspection. If “U” bolt clips are used and the manufacturers' recommendations are not available, table 1 of appendix II to this part shall be used to determine the number and spacing of clips. “U” bolts shall be applied with the “U” section in contact with the dead end of the rope.
(6)
Wire rope shall not be secured by knotting.
(7)
Eyes in wire rope bridles, slings, bull wires, or in single parts used for hoisting shall not be formed by wire rope clips or knots.
(8)
Eye splices in wire ropes shall have at least three tucks with a whole strand of the rope, and two tucks with one-half of the wire cut from each strand. Other forms of splices or connections that the employer demonstrates to be equivalently safe may be used.
(9)
Except for eye splices in the ends of wires and endless rope slings, each wire rope used in hoisting or lowering, or bulling cargo, shall consist of one continuous piece without knot or splice.
(c)
Natural fiber rope.
(1)
The employer shall follow the manufacturers' recommended ratings for natural fiber rope and natural fiber rope slings provided for use aboard ship, and shall have such ratings available for inspection.
(2)
If the manufacturers' recommended ratings and use recommendations are unavailable, the employer shall use table 2 of appendix II to this part to determine safe working loads of natural fiber rope slings comprising part of pre-slung drafts.
(3)
Eye splices shall consist of at least three full tucks. Short splices shall consist of at least six tucks, three on each side of the centerline.
(d)
Synthetic rope.
(1)
The employer shall follow the manufacturers' ratings and use recommendations for the specific synthetic fiber rope and synthetic fiber rope slings provided for use aboard ship, and shall have such ratings available for inspection.
(2)
If the manufacturers' recommended ratings and use recommendations are unavailable, tables 3A and B of appendix II to this part shall be used to determine the safe working load of synthetic fiber rope and of synthetic rope slings that comprise this part of pre-slung drafts.
(3)
(i)
Unless otherwise recommended by the manufacturer, when synthetic fiber ropes are substituted for fiber ropes of less than three inches (7.62 cm) in circumference, the substitute shall be of equal size. Where substituted for fiber rope of three inches or more in circumference, the size of the synthetic rope shall be determined from the formula:
(ii)
In making such substitution, it shall be ascertained that the inherent characteristics of the synthetic fiber are suitable for hoisting.
(e)
Removal of natural and synthetic rope from service. Natural and synthetic rope having any of the following defects shall be removed from service:
(1)
Abnormal or excessive wear including heat and chemical damage;
(2)
Powdered fiber between strands;
(3)
Sufficient cut or broken fibers to affect the capability of the rope;
(4)
Variations in the size or roundness of strands;
(5)
Discolorations other than stains not associated with rope damage;
(6)
Rotting; or
(7)
Distortion or other damage to attached hardware.
(f)
Thimbles. Properly fitting thimbles shall be used when any rope is secured permanently to a ring, shackle or attachment, where practicable.
(g)
Synthetic web slings.
(1)
Slings and nets or other combinations of more than one piece of synthetic webbing assembled and used as a single unit (synthetic web slings) shall not be used to hoist loads greater than the sling's rated capacity.
(2)
Synthetic web slings shall be removed from service if they exhibit any of the following defects:
(i)
Acid or caustic burns;
(ii)
Melting or charring of any part of the sling surface;
(iii)
Snags, punctures, tears or cuts;
(iv)
Broken or worn stitches;
(v)
Distortion or damage to fittings; or
(vi)
Display of visible warning threads or markers designed to indicate excessive wear or damage.
(3)
Defective synthetic web slings removed from service shall not be returned to service unless repaired by a sling manufacturer or an entity of similar competence. Each repaired sling shall be proof tested by the repairer to twice the sling's rated capacity before its return to service. The employer shall retain a certificate of the proof test and make it available for inspection.
(4)
Synthetic web slings provided by the employer shall only be used according to the manufacturers' use recommendations, which shall be available.
(5)
Fittings shall have a breaking strength at least equal to that of the sling to which they are attached and shall be free of sharp edges.
(h)
Chains and chain slings used for hoisting.
(1)
The employer shall follow the manufacturers' recommended ratings for safe working loads for the size of wrought iron and alloy steel chains and chain slings and shall have such ratings available for inspection. When the manufacturer does not provide such ratings, the employer shall use table 4A of appendix II to this part to determine safe working loads for alloy steel chains and chain slings only.
(2)
Proof coil steel chain, also known as common or hardware chain, and other chain not recommended by the manufacturer for slinging or hoisting shall not be used for slinging or hoisting.
(3)
(i)
Sling chains, including end fastenings, shall be inspected for visible defects before each day's use and as often as necessary during use to ensure integrity of the sling.
(ii)
Thorough inspections of chains in use shall be made quarterly to detect wear, defective welds, deformation or increase in length or stretch. The month of inspection shall be shown on each chain by color of paint on a link or by other equally effective means.
(iii)
Chains shall be removed from service when maximum allowable wear, as indicated in table 4B of appendix II to this part, is reached at any point of a link.
(iv)
Chain slings shall be removed from service when stretch has increased the length of a measured section by more than 5 percent; when a link is bent, twisted or otherwise damaged; or when a link has a raised scarf or defective weld.
(v)
Only designated persons shall inspect chains used for slinging and hoisting.
(4)
Chains shall only be repaired by a designated person. Links or portions of a chain defective under any of the criteria of paragraph (h)(3)(iv) of this section shall be replaced with properly dimensioned links or connections of material similar to that of the original chain. Before repaired chains are returned to service, they shall be tested to the proof test load recommended by the manufacturer for the original chain. Tests shall be done by the manufacturer or shall be certified by an agency accredited for the purpose under part 1919 of this chapter. Test certificates shall be available for inspection.
(5)
(i)
Wrought iron chains in constant use shall be annealed or normalized at intervals not exceeding six months. Heat treatment certificates shall be available for inspection. Alloy chains shall not be annealed.
(ii)
Any part of a lifting appliance or item of loose gear installed after January 21, 1998 shall not be manufactured of wrought iron.
(6)
Kinked or knotted chains shall not be used for lifting. Chains shall not be shortened by bolting, wiring or knotting. Makeshift links or fasteners such as wire, bolts or rods shall not be used.
(7)
Hooks, rings, links and attachments affixed to sling chains shall have rated capacities at least equal to those of the chains to which they are attached.
(8)
Chain slings shall bear identification of size, grade and rated capacity.
(i)
Shackles.
(1)
If the manufacturers' recommended safe working loads for shackles are available, they shall not be exceeded. If the manufacturers' recommendations are not available, table 5 of appendix II to this part shall apply.
(2)
Screw pin shackles provided by the employer and used aloft, except in cargo hook assemblies, shall have their pins positively secured.
(j)
Hooks other than hand hooks.
(1)
The manufacturer's recommended safe working loads for hooks shall not be exceeded. Hooks other than hand hooks shall be tested before initial use in accordance with the provisions of § 1919.31 (a), (c), and (d) of this chapter. Exception: Manufacturers' test certificates indicating performance to the criteria in § 1919.31 (a), (c) and (d) of this chapter shall be acceptable.
(2)
Bent or sprung hooks shall be discarded.
(3)
Teeth of case hooks shall be maintained in safe condition.
(4)
Jaws of patent clamp-type plate hooks shall be maintained in condition to grip plates securely.
(5)
Loads shall be applied to the throat of the hook only.
(k)
Pallets.
(1)
Pallets shall be made and maintained to support and carry loads being handled safely. Fastenings of reusable pallets used for hoisting shall be bolts and nuts, drive screws (helically threaded nails), annular threaded nails or fastenings of equivalent holding strength.
(2)
Reusable wing or lip-type pallets shall be hoisted by bar bridles or other suitable gear and shall have an overhanging wing or lip of at least three inches (7.6 cm). They shall not be hoisted by wire slings alone.
(3)
Loaded pallets that do not meet the requirements of this paragraph shall be hoisted only after being placed on pallets meeting such requirements, or shall be handled by other means providing equivalent safety.
(4)
Bridles for handling flush end or box-type pallets shall be designed to prevent disengagement from the pallet under load.
(5)
Pallets shall be stacked or placed to prevent falling, collapsing or otherwise causing a hazard under standard operating conditions.
(6)
Disposable pallets intended only for one use shall not be reused for hoisting.
Notes, amendments, and revision history

Amendments

[62 FR 40202, July 25, 1997, as amended at 65 FR 40945, June 30, 2000]

Authority

Authority: 33 U.S.C. 941; 29 U.S.C. 653, 655, 657; Secretary of Labor's Order No. 12-71 (36 FR 8754), 8-76 (41 FR 25059), 9-83 (48 FR 35736), 1-90 (55 FR 9033), 6-96 (62 FR 111), 3-2000 (65 FR 50017), 5-2002 (67 FR 65008), 5-2007 (72 FR 31160), 4-2010 (75 FR 55355), 1-2012 (77 FR 3912), or 8-2020 (85 FR 58393), as applicable; and 29 CFR 1911. Sections 1918.90 and 1918.110 also issued under 5 U.S.C. 553. Section 1918.100 also issued under 49 U.S.C. 5101 et seq. and 5 U.S.C. 553.

Source

Source: 62 FR 40202, July 25, 1997, unless otherwise noted.

Amendments

[62 FR 40202, July 25, 1997, as amended at 65 FR 40945, June 30, 2000]

§1918.63. Chutes, gravity conveyors and rollers.

29 C.F.R. § 1918.63

(a)
Chutes shall be of adequate length and strength to support the conditions of use, and shall be free of splinters and sharp edges.
(b)
When necessary for the safety of employees, chutes shall be equipped with sideboards to afford protection from falling objects.
(c)
When necessary for the safety of employees, provisions shall be made for stopping objects other than bulk commodities at the delivery end of the chute.
(d)
Chutes and gravity conveyor roller sections shall be firmly placed and secured to prevent displacement, shifting, or falling.
(e)
Gravity conveyors shall be of sufficient strength to support the weight of materials placed upon them safely. Conveyor rollers shall be installed in a way that prevents them from falling or jumping out of the frame.
(f)
Frames shall be kept free of burrs and sharp edges.
Notes, amendments, and revision history

Authority

Authority: 33 U.S.C. 941; 29 U.S.C. 653, 655, 657; Secretary of Labor's Order No. 12-71 (36 FR 8754), 8-76 (41 FR 25059), 9-83 (48 FR 35736), 1-90 (55 FR 9033), 6-96 (62 FR 111), 3-2000 (65 FR 50017), 5-2002 (67 FR 65008), 5-2007 (72 FR 31160), 4-2010 (75 FR 55355), 1-2012 (77 FR 3912), or 8-2020 (85 FR 58393), as applicable; and 29 CFR 1911. Sections 1918.90 and 1918.110 also issued under 5 U.S.C. 553. Section 1918.100 also issued under 49 U.S.C. 5101 et seq. and 5 U.S.C. 553.

Source

Source: 62 FR 40202, July 25, 1997, unless otherwise noted.

§1918.64. Powered conveyors.

29 C.F.R. § 1918.64

(a)
Emergency stop. Readily accessible stop controls shall be provided for use in an emergency. Whenever the operation of any power conveyor requires personnel to work close to the conveyor, the conveyor controls shall not be left unattended while the conveyor is in operation.
(b)
Guarding. All conveyor and trimmer drives that create a hazard shall be adequately guarded.
(c)
Approved for location. Electric motors and controls on conveyors and trimmers used to handle grain and exposed to grain dust shall be of a type approved by a nationally recognized testing laboratory for use in Class II, Division I locations. (See § 1910.7 of this chapter.)
(d)
Grain trimmer control box. Each grain trimmer shall have a control box on the weather deck close to the spout feeding the trimmer.
(e)
Grain trimmer power cable. Power cables between the deck control box and the grain trimmer shall be used only in continuous lengths without splice or tap between connections.
(f)
Portable conveyors. Portable conveyors shall be stable within their operating ranges. When used at variable fixed levels, the unit shall be secured at the operating level.
(g)
Delivery and braking. When necessary for the safety of employees, provisions shall be made for braking objects at the delivery end of the conveyor.
(h)
Electric brakes. Conveyors using electrically released brakes shall be constructed so that the brakes cannot be released until power is applied and the brakes are automatically engaged if the power fails or the operating control is returned to the “stop” position.
(i)
Starting powered conveyors. Powered conveyors shall not be started until all employees are clear of the conveyor or have been warned that the conveyor is about to start up.
(j)
Loading and unloading. The area around conveyor loading and unloading points shall be kept clear of obstructions during conveyor operations.
(k)
Lockout/tagout.
(1)
Conveyors shall be stopped and their power sources locked out and tagged out during maintenance, repair, and servicing. If power is necessary for testing or for making minor adjustments, power shall only be supplied to the servicing operation.
(2)
The starting device shall be locked out and tagged out in the stop position before an attempt is made to remove the cause of a jam or overload of the conveying medium.
(l)
Safe practices.
(1)
Only designated persons shall operate, repair or service powered conveyors.
(2)
The employer shall ensure that each employee stays off operating conveyors.
(3)
Conveyors shall be operated only with all overload devices, guards and safety devices in place and operable.
Notes, amendments, and revision history

Authority

Authority: 33 U.S.C. 941; 29 U.S.C. 653, 655, 657; Secretary of Labor's Order No. 12-71 (36 FR 8754), 8-76 (41 FR 25059), 9-83 (48 FR 35736), 1-90 (55 FR 9033), 6-96 (62 FR 111), 3-2000 (65 FR 50017), 5-2002 (67 FR 65008), 5-2007 (72 FR 31160), 4-2010 (75 FR 55355), 1-2012 (77 FR 3912), or 8-2020 (85 FR 58393), as applicable; and 29 CFR 1911. Sections 1918.90 and 1918.110 also issued under 5 U.S.C. 553. Section 1918.100 also issued under 49 U.S.C. 5101 et seq. and 5 U.S.C. 553.

Source

Source: 62 FR 40202, July 25, 1997, unless otherwise noted.

§1918.65. Mechanically powered vehicles used aboard vessels.

29 C.F.R. § 1918.65

(a)
Applicability. This section applies to every type of mechanically powered vehicle used for material or equipment handling aboard a vessel.
(b)
General.
(1)
Modifications, such as adding counterweights that might affect the vehicle's capacity or safety, shall not be done without either the manufacturers' prior written approval or the written approval of a registered professional engineer experienced with the equipment, who has consulted with the manufacturer, if available. Capacity, operation and maintenance instruction plates, tags or decals shall be changed to conform to the equipment as modified.
(2)
Rated capacities, with and without removable counterweights, shall not be exceeded. Rated capacities shall be marked on the vehicle and shall be visible to the operator. The vehicle weight, with and without a counterweight, shall be similarly marked.
(3)
If loads are lifted by two or more trucks working in unison, the total weight shall not exceed the combined safe lifting capacity of all trucks.
(c)
Guards for fork lift trucks.
(1)
Except as noted in paragraph (c)(5) of this section, fork lift trucks shall be equipped with overhead guards securely attached to the machines. The guard shall be of such design and construction as to protect the operator from boxes, cartons, packages, bagged material, and other similar items of cargo that might fall from the load being handled or from stowage.
(2)
Overhead guards shall not obstruct the operator's view, and openings in the top of the guard shall not exceed six inches (15.24 cm) in one of the two directions, width or length. Larger openings are permitted if no opening allows the smallest unit of cargo being handled through the guard.
(3)
Overhead guards shall be built so that failure of the vehicle's mast tilting mechanism will not displace the guard.
(4)
Overhead guards shall be large enough to extend over the operator during all truck operations, including forward tilt.
(5)
An overhead guard may be removed only when it would prevent a truck from entering a work space and only if the operator is not exposed to low overhead obstructions in the work space.
(6)
Where necessary to protect the operator, fork lift trucks shall be fitted with a vertical load backrest extension to prevent the load from hitting the mast when the mast is positioned at maximum backward tilt. For this purpose, a “load backrest extension” means a device extending vertically from the fork carriage frame to prevent raised loads from falling backward.
(d)
Guards for bulk cargo-moving vehicles.
(1)
Every crawler type, rider operated, bulk cargo-moving vehicle shall be equipped with an operator's guard of such design and construction as to protect the operator, when seated, against injury from contact with a projecting overhead hazard.
(2)
Overhead guards and their attachment points shall be so designed as to be able to withstand, without excessive deflection, a load applied horizontally at the operator's shoulder level equal to the drawbar pull of the machine.
(3)
Overhead guards are not required when the vehicle is used in situations in which the seated operator cannot contact projecting overhead hazards.
(4)
After July 26, 1999, bulk cargo-moving vehicles shall be equipped with rollover protection of such design and construction as to prevent the possibility of the operator being crushed because of a rollover or upset.
(e)
Approved trucks.
(1)
“Approved power-operated industrial truck” means one listed as approved for the intended use or location by a nationally recognized testing laboratory (see § 1910.7 of this chapter).
(2)
Approved power-operated industrial trucks shall bear a label or other identification indicating testing laboratory approval.
(3)
When the atmosphere in an area is hazardous (see § 1918.2 and § 1918.93), only approved power-operated industrial trucks shall be used.
(f)
Maintenance.
(1)
Mechanically powered vehicles shall be maintained in safe working order. Safety devices shall not be removed or made inoperative except where permitted in this section. Vehicles with a fuel system leak or any other safety defect shall not be operated.
(2)
Braking systems or other mechanisms used for braking shall be operable and in safe condition.
(3)
Replacement parts whose function might affect operational safety shall be equivalent in strength and performance capability to the original parts that they replace.
(4)
Repairs to the fuel and ignition systems of mechanically powered vehicles that involve fire hazards shall be conducted only in locations designated as safe for such repairs.
(5)
Batteries on all mechanically powered vehicles shall be disconnected during repairs to the primary electrical system except when power is necessary for testing and repair. On vehicles equipped with systems capable of storing residual energy, that energy shall be safely discharged before work on the primary electrical system begins.
(6)
Only designated persons shall do maintenance and repair.
(g)
Parking brakes. All mechanically powered vehicles purchased after January 21, 1998, shall be equipped with parking brakes.
(h)
Operation.
(1)
Only stable and safely arranged loads within the rated capacity of the mechanically powered vehicle shall be handled.
(2)
The employer shall require drivers to ascend and descend grades slowly.
(3)
If the load obstructs the forward view, the employer shall require drivers to travel with the load trailing.
(4)
Steering knobs shall not be used unless the vehicle is equipped with power steering.
(5)
When mechanically powered vehicles use cargo lifting devices that have a means of engagement hidden from the operator, a means shall be provided to enable the operator to determine that the cargo has been engaged.
(6)
No load on a mechanically powered vehicle shall be suspended or swung over any employee.
(7)
When mechanically powered vehicles are used, provisions shall be made to ensure that the working surface can support the vehicle and load, and that hatch covers, truck plates, or other temporary surfaces cannot be dislodged by movement of the vehicle.
(8)
When mechanically powered vehicles are left unattended, load-engaging means shall be fully lowered, controls neutralized, brakes set and power shut off. Wheels shall be blocked or curbed if the vehicle is on an incline.
(9)
When lift trucks or other mechanically powered vehicles are being operated on open deck-type barges, the edges of the barges shall be guarded by railings, sideboards, timbers, or other means sufficient to prevent vehicles from rolling overboard. When such vehicles are operated on covered lighters where door openings other than those being used are left open, means shall be provided to prevent vehicles from rolling overboard through such openings.
(10)
Unauthorized personnel shall not ride on mechanically powered vehicles. A safe place to ride shall be provided when riding is authorized.
(11)
An employee may be elevated by fork lift trucks only when a platform is secured to the lifting carriage or forks. The platform shall meet the following requirements:
(i)
The platform shall have a railing complying with § 1917.112(c) of this chapter.
(ii)
The platform shall have toeboards complying with § 1917.112(d) of this chapter, if tools or other objects could fall on employees below.
(iii)
When the truck has controls elevated with the lifting carriage, means shall be provided for employees on the platform to shut off power to the vehicle.
(iv)
Employees on the platform shall be protected from exposure to moving truck parts.
(v)
The platform floor shall be skid resistant.
(vi)
An employee shall be at the truck's controls whenever employees are elevated.
(vii)
While an employee is elevated, the truck may be moved only to make minor adjustments in placement.
Notes, amendments, and revision history

Amendments

[62 FR 40202, July 25, 1997, as amended at 65 FR 40945, June 30, 2000]

Authority

Authority: 33 U.S.C. 941; 29 U.S.C. 653, 655, 657; Secretary of Labor's Order No. 12-71 (36 FR 8754), 8-76 (41 FR 25059), 9-83 (48 FR 35736), 1-90 (55 FR 9033), 6-96 (62 FR 111), 3-2000 (65 FR 50017), 5-2002 (67 FR 65008), 5-2007 (72 FR 31160), 4-2010 (75 FR 55355), 1-2012 (77 FR 3912), or 8-2020 (85 FR 58393), as applicable; and 29 CFR 1911. Sections 1918.90 and 1918.110 also issued under 5 U.S.C. 553. Section 1918.100 also issued under 49 U.S.C. 5101 et seq. and 5 U.S.C. 553.

Source

Source: 62 FR 40202, July 25, 1997, unless otherwise noted.

Amendments

[62 FR 40202, July 25, 1997, as amended at 65 FR 40945, June 30, 2000]

§1918.66. Cranes and derricks other than vessel's gear.

29 C.F.R. § 1918.66

(a)
General. The following requirements shall apply to the use of cranes and derricks brought aboard vessels for conducting longshoring operations. They shall not apply to cranes and derricks forming part of a vessel's permanent equipment.
(1)
Certification. Cranes and derricks shall be certificated in accordance with part 1919 of this chapter.
(2)
Posted weight. The crane weight shall be posted on all cranes hoisted aboard vessels for temporary use.
(3)
Rating chart. All cranes and derricks having ratings that vary with boom length, radius (outreach) or other variables shall have a durable rating chart visible to the operator, covering the complete range of the manufacturers' (or design) capacity ratings. The rating chart shall include all operating radii (outreach) for all permissible boom lengths and jib lengths, as applicable, with and without outriggers, and alternate ratings for optional equipment affecting such ratings. Precautions or warnings specified by the owner or manufacturer shall be included along with the chart.
(4)
Rated loads. The manufacturers' (or design) rated loads for the conditions of use shall not be exceeded.
(5)
Change of rated loads. Designated working loads shall not be increased beyond the manufacturers' ratings or original design limitations unless such increase receives the manufacturers' approval. When the manufacturers' services are not available or where the equipment is of foreign manufacture, engineering design analysis shall be done or approved by a person accredited for certificating the equipment under part 1919 of this chapter. Engineering design analysis shall be done by a registered professional engineer competent in the field of cranes and derricks. Any structural changes required by the change in rating shall be carried out.
(6)
Radius indicator. When the rated load varies with the boom radius, the crane or derrick shall be fitted with a boom angle or radius indicator visible to the operator.
(7)
Operator's station. The cab, controls and mechanism of the equipment shall be so arranged that the operator has a clear view of the load or signalman, when one is used. Cab glass, when used, shall be safety plate glass or equivalent. Cranes with missing, broken, cracked, scratched, or dirty glass (or equivalent), that impairs operator vision shall not be used. Clothing, tools, and equipment shall be stored so as not to interfere with access, operation, and the operator's view.
(8)
Counterweights or ballast. Cranes shall be operated only with the specified type and amount of ballast or counterweights. Ballast or counterweights shall be located and secured only as provided in the manufacturers' or design specifications, which shall be available for inspection.
(9)
Outriggers. Outriggers shall be used according to the manufacturers' specifications or design data, which shall be available for inspection. Floats, when used, shall be securely attached to the outriggers. Wood blocks or other support shall be of sufficient size to support the outrigger, free of defects that may affect safety, and of sufficient width and length to prevent the crane from shifting or toppling under load.
(10)
Exhaust gases. Engine exhaust gases shall be discharged away from crane operating personnel.
(11)
Electrical/Guarding. Electrical equipment shall be so placed or enclosed that live parts will not be exposed to accidental contact. Designated persons may work on energized equipment only if necessary during inspection, maintenance, or repair; otherwise the equipment shall be stopped and its power source locked out and tagged out.
(12)
Fire extinguisher.
(i)
At least one portable approved or listed fire extinguisher of at least a 5-B— C rating or equivalent shall be accessible in the cab of the crane or derrick.
(ii)
No portable fire extinguisher using carbon tetrachloride or chlorobromomethane extinguishing agents shall be used.
(13)
Rope on drums. At least three full turns of rope shall remain on ungrooved drums, and two turns on grooved drums, under all operating conditions. Wire rope shall be secured to drums by clamps, U-bolts, shackles or equivalent means. Fiber rope fastenings are prohibited.
(14)
Brakes.
(i)
Each independent hoisting unit of a crane shall be equipped with at least one holding brake, applied directly to the motor shaft or gear train.
(ii)
Each independent hoisting unit of a crane shall, in addition to the holding brake, be equipped with a controlled braking means to control lowering speeds.
(iii)
Holding brakes for hoist units shall have not less than the following percentage of the rated load hoisting torque at the point where the brake is applied:
(A)
125 percent when used with an other than mechanically controlled braking means;
(B)
100 percent when used with a mechanically controlled braking means; or
(C)
100 percent when two holding brakes are provided.
(iv)
All power control braking means shall be capable of maintaining safe lowering speeds of rated loads.
(15)
Operating controls. Crane and derrick operating controls shall be clearly marked, or a chart showing their function shall be posted at the operator's position.
(16)
Booms. Cranes with elevatable booms and without operable automatic limiting devices shall be provided with boom stops if boom elevation can exceed maximum design angles from the horizontal.
(17)
Foot pedals. Foot pedals shall have a non-skid surface.
(18)
Access. Ladders, stairways, stanchions, grab irons, foot steps or equivalent means shall be provided as necessary to ensure safe access to footwalks, cab platforms, the cab and any portion of the superstructure that employees must reach.
(b)
Operations—
(1)
Use of cranes together. When two or more cranes hoist a load in unison, a designated person shall direct the operation and instruct personnel in positioning, rigging of the load and movements to be made.
(2)
Guarding of swing radius. Accessible areas within the swing radius of the body of a revolving crane shall be physically guarded during operations to prevent an employee from being caught between the body of the crane and any fixed structure or between parts of the crane.
(3)
Prohibited usage.
(i)
Equipment shall not be used in a way that exerts side loading stresses upon the crane or derrick boom.
(ii)
No crane or derrick having a visible or known defect that may affect safe operation shall be used.
(4)
Unattended cranes. The following steps shall be taken before leaving a crane unattended between work periods:
(i)
Suspended loads, such as those hoisted by lifting magnets or clamshell buckets, shall be landed unless the storage position or maximum hoisting of the suspended device will provide equivalent safety;
(ii)
Clutches shall be disengaged;
(iii)
The power supply shall be shut off;
(iv)
The crane shall be secured against accidental travel; and
(v)
The boom shall be lowered or secured against movement.
(c)
Protection for employees being hoisted.
(1)
No employee shall be hoisted by the load hoisting apparatus of a crane or derrick except on a platform meeting the following requirements:
(i)
Enclosed by a railing or other means providing protection equivalent to that described in § 1917.112(c) of this chapter;
(ii)
Fitted with toe boards if the platform has open railings;
(iii)
A safety factor of four based on ultimate strength;
(iv)
Bearing a plate or permanent marking indicating maximum load rating, which shall not be exceeded, and the weight of the platform itself;
(v)
Equipped with a device to prevent access doors, when used, from opening accidentally;
(vi)
Equipped with overhead protection for employees on the platform if they are exposed to falling objects or overhead hazards; and
(vii)
Secured to the load line by means other than wedge and socket attachments, unless the free (bitter) end of the line is secured back to itself by a clamp placed as close above the wedge as possible.
(2)
Except in an emergency, the hoisting mechanism of all cranes or derricks used to hoist personnel shall operate only in power up and power down, with automatic brake application when not hoisting or lowering.
(3)
All cranes and derricks used to hoist personnel shall be equipped with an anti-two-blocking device.
(4)
Variable radius booms of a crane or derrick used to hoist personnel shall be so constructed or secured as to prevent accidental boom movement.
(5)
Platforms or devices used to hoist employees shall be inspected for defects before each day's use and shall be removed from service if defective.
(6)
Employees being hoisted shall remain in continuous sight of and communication with the operator or signalman.
(7)
Operators shall remain at the controls when employees are hoisted.
(8)
Cranes shall not travel while employees are hoisted, except in emergencies or in normal tier-to-tier transfer of employees during container operations.
(d)
Routine inspection.
(1)
Designated persons shall visually inspect each crane and derrick on each day of use for defects in functional operating components and shall report any defect found to the employer. The employer shall inform the operator of the result of the inspection.
(2)
A designated person shall thoroughly inspect all functional components and accessible structural features of each crane or device at monthly intervals.
(3)
Any defects found during such inspections that may create a safety hazard shall be corrected before further equipment use. Repairs shall be done only by designated persons.
(4)
A record of each monthly inspection shall be maintained for six months in or on the crane or derrick or at the terminal.
(e)
Protective devices.
(1)
When exposed moving parts such as gears, chains and chain sprockets present a hazard to employees during crane and derrick operations, those parts shall be securely guarded.
(2)
Crane hooks shall be latched or otherwise secured to prevent accidental load disengagement.
(f)
Load-indicating devices.
(1)
Unless exempted by the provisions of paragraph (f)(1)(viii) of this section, every crane used to load or discharge cargo into or out of a vessel shall be fitted with a load-indicating device or alternative device in proper working condition that shall meet the following criteria:
(i)
The type or model of any load-indicating device used shall be such as to provide:
(A)
A direct indication in the cab of actual weight hoisted or a means of determining this by reference to crane ratings posted and visible to the operator, except that the use of a dynamometer or simple scale alone will not meet this requirement; or
(B)
An automatic weight-moment device (e.g., a computer) providing indications in the cab according to the radius and load at the moment; or
(C)
A device that will prevent an overloaded condition.
(ii)
The accuracy of the load-indicating device, weight-moment device, or overload protection device shall be such that any indicated load (or limit), including the sum of actual weight hoisted and additional equipment or “add ons” such as slings, sensors, blocks, etc., is within the range between 95 percent (5 percent underload) and 110 percent (10 percent overload) of the actual true total load. Such accuracy shall be required over the range of daily operating variables reasonably anticipated under the conditions of use.
(iii)
The device shall enable the operator to decide before making any lift that the load indicating device or alternative device is operative. In the alternative, if the device is not so mounted or attached and does not include such means of checking, it shall be certified by the manufacturer to remain operative for a specific time. The device shall be checked for accuracy, using known values of the load, at the time of every certification survey (see § 1918.11) and at such additional times as may be recommended by the manufacturer.
(iv)
When the load indicating device or alternative device is so arranged in the supporting system (crane structure) that its failure could cause the load to be dropped, its strength shall not be the limiting factor of the supporting system (crane structure).
(v)
Units of measure in pounds or both pounds and kilograms (or other indicators of measurement, such as colored indicator lights), capacity of the indicating system, accuracy of the indicating system, and operating instructions and precautions shall be conspicuously marked. If the system used provides no readout but automatically ceases crane operation when the rated load limit is reached under any specific condition of use, the marking shall provide the make and model of the device installed, a description of what it does, how it is operated, and any necessary precautions regarding the system. All of these markings shall be readily visible to the operator.
(vi)
All load indicating devices shall operate over the full operating radius. Overall accuracy shall be based on actual applied loads and not on full scale (full capacity) load.
(vii)
When a load-indicating device uses the radius as a factor in its use or in its operating indications, the indicated radius (which may be in feet and/or meters, or degrees of boom angle, depending on the system used) shall be within the range between 97 percent and 110 percent of the actual (true) radius. When radius is presented in degrees, and feet or meters are required for necessary determinations, a conversion chart shall be provided.
(viii)
The load indicating device requirements of this paragraph do not apply to a crane—
(A)
Of the trolley equipped bridge type while handling containers known to be and identified as empty, or loaded, and in either case according to the provisions of § 1918.85(b) of this part, or while hoisting other lifts by means of a lifting beam supplied by the crane manufacturer for the purpose and in all cases within the crane rating;
(B)
While handling bulk commodities or cargoes by means of clamshell bucket or magnet;
(C)
While used to handle or hold hoses in connection with transfer of bulk liquids, or other hose-handled products; or
(D)
While the crane is used exclusively to handle cargo or equipment whose total actual gross weight is marked on the unit or units hoisted, and the total actual gross weight never exceeds 11,200 lbs., and the load is less than the rated capacity of the crane at the maximum outreach possible at the time.
(2)
[Reserved]
Notes, amendments, and revision history

Amendments

[62 FR 40202, July 25, 1997, as amended at 65 FR 40945, June 30, 2000]

Authority

Authority: 33 U.S.C. 941; 29 U.S.C. 653, 655, 657; Secretary of Labor's Order No. 12-71 (36 FR 8754), 8-76 (41 FR 25059), 9-83 (48 FR 35736), 1-90 (55 FR 9033), 6-96 (62 FR 111), 3-2000 (65 FR 50017), 5-2002 (67 FR 65008), 5-2007 (72 FR 31160), 4-2010 (75 FR 55355), 1-2012 (77 FR 3912), or 8-2020 (85 FR 58393), as applicable; and 29 CFR 1911. Sections 1918.90 and 1918.110 also issued under 5 U.S.C. 553. Section 1918.100 also issued under 49 U.S.C. 5101 et seq. and 5 U.S.C. 553.

Source

Source: 62 FR 40202, July 25, 1997, unless otherwise noted.

Amendments

[62 FR 40202, July 25, 1997, as amended at 65 FR 40945, June 30, 2000]