§601.2. Applications for biologics licenses; procedures for filing. — Inbound Citations

Abbreviated new drug application (ANDA) has the same meaning given the term “abbreviated application” in § 314.3(b) of this chapter.

A biologics license issued to a manufacturer and covering all locations of manufacture shall authorize persons other than such manufacturer to conduct at places other than such locations the initial, and partial manufacturing of a product for shipment solely to such manufacturer only to the extent that the names of such persons and places are registered with the Commissioner of Food and Drugs and it is found upon application of such manufacturer, that the product is in short supply due either to the peculiar growth requirements of the organism involved or to the scarcity of the animal required for manufacturing purposes, and such manufacturer has established with respect to such persons and places such procedures, inspections, tests or other arrangements as will ensure full compliance with the applicable regulations of this subchapter related to continued safety, purity, and potency. Such persons and places shall be subject to all regulations of this subchapter except §§ 601.2 to 601.6, 601.9, 601.10, 601.20, 601.21 to 601.33, and 610.60 to 610.65 of this chapter. For persons and places authorized under this section to conduct the initial and partial manufacturing of a product for shipment solely to a manufacturer of a product subject to licensure under § 601.2(c), the following additional regulations shall not be applicable: §§ 600.10(b) and (c), 600.11, 600.12, 600.13, and 610.53 of this chapter. Failure of such manufacturer to maintain such procedures, inspections, tests, or other arrangements, or failure of any person conducting such partial manufacturing to comply with applicable regulations shall constitute a ground for suspension or revocation of the authority conferred pursuant to this section on the same basis as provided in §§ 601.6 to 601.8 with respect to the suspension and the revocation of licenses.

(iii) Mold manufacturers shall maintain written standard operating procedures, developed by a qualified individual, that will ensure the identity of the seed culture, prescribe adequate processing of the mold, and specify the acceptable limits and kinds of contamination. These limits shall be based on results of appropriate tests performed by the manufacturer on at least three consecutive lots of a mold that is a representative species of mold subject to the standard operating procedures. The tests shall be performed at each manufacturing step during and subsequent to harvest, as specified in the standard operating procedures. Before use of the mold as a source material for Allergenic Products, in accordance with 21 CFR 601.2, the standard operating procedures and test data from the three representative lots described above shall be submitted to and approved by the Director, Center for Biologics Evaluation and Research (see mailing address in § 600.2(a) of this chapter).

(b) To obtain marketing approval for radioactive biological products for human use, as defined in § 600.3(ee) of this chapter, manufacturers must comply with the provisions of § 601.2(a) of this chapter.

(b) The content of labeling required under § 201.100(d)(3) of this chapter (commonly referred to as the package insert or professional labeling), including all text, tables, and figures, must be submitted to the agency in electronic format as described in paragraph (a) of this section. This requirement is in addition to the provisions of §§ 601.2(a) and 601.12(f) that require applicants to submit specimens of the labels, enclosures, and containers, or to submit other final printed labeling. Submissions under this paragraph must be made in accordance with part 11 of this chapter except for the requirements of § 11.10(a), (c) through (h), and (k), and the corresponding requirements of § 11.30.

A biologics license issued to a manufacturer and covering all locations of manufacture shall authorize persons other than such manufacturer to conduct at places other than such locations the initial, and partial manufacturing of a product for shipment solely to such manufacturer only to the extent that the names of such persons and places are registered with the Commissioner of Food and Drugs and it is found upon application of such manufacturer, that the product is in short supply due either to the peculiar growth requirements of the organism involved or to the scarcity of the animal required for manufacturing purposes, and such manufacturer has established with respect to such persons and places such procedures, inspections, tests or other arrangements as will ensure full compliance with the applicable regulations of this subchapter related to continued safety, purity, and potency. Such persons and places shall be subject to all regulations of this subchapter except §§ 601.2 to 601.6, 601.9, 601.10, 601.20, 601.21 to 601.33, and 610.60 to 610.65 of this chapter. For persons and places authorized under this section to conduct the initial and partial manufacturing of a product for shipment solely to a manufacturer of a product subject to licensure under § 601.2(c), the following additional regulations shall not be applicable: §§ 600.10(b) and (c), 600.11, 600.12, 600.13, and 610.53 of this chapter. Failure of such manufacturer to maintain such procedures, inspections, tests, or other arrangements, or failure of any person conducting such partial manufacturing to comply with applicable regulations shall constitute a ground for suspension or revocation of the authority conferred pursuant to this section on the same basis as provided in §§ 601.6 to 601.8 with respect to the suspension and the revocation of licenses.